Controls And Features (Input Card: Optional) - JVC DT-V1910CG Instructions Manual

CONTROLS AND FEATURES
19 Power lamp
Unlit : The main power is OFF.
Orange : The main power is ON, but the monitor's power
is OFF (in stand-by mode).
Green : The main power is ON, and the monitor's
power is ON (in normal operation mode).
REAR/SIDE VIEW
<Rear Panel>
REMOTE
MAKE/TRIGGER
G/Y SWITCHED 21
OUT
RS-485
B/P IN /B-Y OUT
B IN
HD SDI 1
IN OUT
R/P R /B-Y IN
OUT
IN OUT
HD/C S
22
IN
IN OUT
VD HD SDI 2
AUDIO
IN IN OUT OUT
AUDIO
IN OUT
IN OUT
23
MAIN POWER
24
REMOTE (external control) terminals
21
Terminals for controlling the monitor from an
external unit.
MAKE/TRIGGER terminal (Upper):
Enables the monitor to be controlled by closing the
circuit (point of contact) connected to the terminal.
RS-485IN terminal:
Enables the monitor to be controlled from a personal
computer via a serial cable.
RS-485 OUT terminal (Lower):
Enables a cascade control connection. Multiple moni-
tors can be controlled by the device connected to the IN
terminal.
Input card slots (SLOT 1 — SLOT 3)
22
Optional input cards can be installed in these
slots. Input cards are not provided when you
purchase the monitor.
NOTE:
It is not possible to input video or audio signals to the monitor
when no input cards are installed.
Main power switch
23
Press the switch to turn the main power ON or
OFF. When the main power is ON, the power
lamp on the front panel lights in yellow and the
monitor enters the stand-by mode.
• I : ON : OFF
6
(cont'd)
20 POWER switch
Press the power switch to turn the monitor's
power ON or OFF when the main power is ON.
NOTE:
When RUSH DELAY TIME is set to SLOW in the set-up menu, it
takes approx. 3.2 seconds for the power to actually turn ON after
the power switch is pressed.
<Side Panel>
25
24 AC inlet
Power input connector. Connect the provided AC
power cord to an AC outlet (120 V/230 V AC, 50
Hz/60 Hz).
Attach the provided Power Cord Holder to prevent
accidental disconnection of the AC power cord.
Refer to page 10 for details.
25 Built-in speaker (monaural)
Outputs the selected INPUT audio signal.
CONTROLS AND FEATURES
(INPUT CARD: OPTIONAL)
COMPONENT/RGB INPUT CARD (IF-C01COMG)
1 Component/RGB signal input/output terminals
Input (IN) and output (OUT) terminals for component (color difference) or
G/Y
RGB signals.
Select component signal: INPUT SELECT A (SLOT1)/C (SLOT2)/E (SLOT3)
IN OUT
B/P /B-Y
B
Select RGB signal
1
* The IN and OUT terminals are bridge-connected (auto termination).
IN OUT
R/P R /B-Y
Synchronized signal input/output terminals
2
Input (IN) and output (OUT) terminals for the vertical, horizontal or complex
4
IN OUT
HD/C S
synchronized signals.
• To use these terminals, set "SYNC SELECT" to "EXT".
2
IN OUT
VD Refer to "SYNC SELECT" on page 17 for more information.
Audio input/output terminals
3
IN IN OUT OUT
AUDIO
Input (IN) and output (OUT) terminals for the analog audio signals.
3
• The IN and OUT terminals are bridge-connected.
IN OUT
Connection terminal
4
Attach to the connection terminal of your Multi-Format Monitor.
Compatible signal formats:
480/60i, 576/50i, 576/50p, 480/60p, 720/
60p, 1035/60i, 1080/50i, 1080/60i, 1080/
24psF
VIDEO INPUT CARD (IF-C01PNG)
1 Composite signal input/output terminals (VIDEO1, VIDEO2)
Input (IN) and output (OUT) terminals for the composite video signals of the
NTSC, PAL, and black/white (50/60Hz).
VIDEO 1
NTSC and PAL are switched in the "COLOR SYSTEM". Refer to "COLOR
SYSTEM" on page 17.
1
IN OUT
VIDEO 2
Select VIDEO 1: press INPUT SELECT A (SLOT1)/C (SLOT2)/E (SLOT3) buttons.
Select VIDEO 2: press INPUT SELECT B (SLOT1)/D (SLOT2)/F (SLOT3) buttons.
IN OUT
* The IN and OUT terminals are bridge-connected (auto termination).
2
Y/C IN
S-video signal input terminal (only for VIDEO 2)
2
EXT .SYNC
Input terminal for the S-video signal.
3
• When an S-video signal is input to this terminal and a video signal is input to VIDEO
IN OUT 2, the S-video signal has priority over the video signal.
AUDIO 1
3 Synchronized signal input/output terminals (for both VIDEO
4
IN OUT
1 and VIDEO 2)
Input (IN) and output (OUT) terminals for the complex synchronized signals.
AUDIO 2
5
To use these terminals, set "SYNC SELECT" to "EXT". Refer to "SYNC
SELECT" on page 17 for more information.
NOTES:
• When an external synchronized signal is input, external synchronization is prioritized
Compatible signal formats:
for both VIDEO1 and VIDEO2.
NTSC (3.58 MHz), PAL (4.43 MHz),
• External synchronization does not function when a video signal (except black burst
black-and-white
signal) is included in the complex synchronized signal.
(50 Hz/60 Hz)
4 Audio signal input/output terminals (for both VIDEO 1 and
VIDEO 2)
Input (IN) and output (OUT) terminals for analog audio signals correspond-
ing to VIDEO 1 and VIDEO 2.
• The IN and OUT terminals are bridge-connected.
Connection terminal
5
Attach to the connection terminal of your Multi-Format Monitor.
: INPUT SELECT B (SLOT1)/D (SLOT2)/F (SLOT3)
7