Table of Contents
Advertisement
Quick Links
-
DISTRIBUTION SOLUTIONS
PDCOM
Installation Manual
-
Disclaimer
The data, examples and diagrams in this manual are
included solely for the concept or product
description and are not a statement of guaranteed
properties. All persons responsible for applying the
equipment described in this manual must ensure
that each intended application is suitable and
acceptable, and that all applicable safety or other
operational requirements are complied with. In
particular, all risks in applications where a system
failure and/or product failure would create a risk of
harm to property or persons (including but not
limited to personal injuries or death) shall be the
sole responsibility of the person or entity who/that
applies the equipment, and such parties are hereby
requested to ensure that all measures are taken to
exclude or mitigate such risks.
This document has been carefully checked by ABB
but discrepancies cannot be completely ruled out. If
discrepancies are detected, the reader is kindly
requested to notify the manufacturer. With the
exception of explicit contractual commitments, in
no event shall ABB be responsible or liable for any
loss or damage resulting from use of this manual or
application of the equipment.
Contents
1.
2.
3.
4.
5.
6.
7.
8.
9.
-
Conformity
The products listed in the document comply with
the directive of the Council of the European
Communities implemented by the laws of the
Member States relating to electromagnetic
compatibility (EMC Directive 2004/108/EC) and
concerning electrical equipment for use within
specified voltage limits (Low-voltage directive
2006/95/EC). Such conformity is the result of tests
conducted by ABB in accordance with product
standards EN50263 and EN60255-26 for the MEC
directive and with product standards EN 60255-1
and EN 60255-27 for the low voltage directive.
3
4
5
6
7
14
18
19
20
21
22
Advertisement
Table of Contents
Related Manuals for ABB PDCOM
Summary of Contents for ABB PDCOM
-
Page 1: Table Of Contents
With the exception of explicit contractual commitments, in no event shall ABB be responsible or liable for any loss or damage resulting from use of this manual or application of the equipment. - Page 2 3.6 Storage 4. Precondition for PDCOM installation 4.1 Checking environmental conditions and installation space SWICOM must be earthed 5. PDCOM interface Mounting (with VPIS) 6. PDCOM interface Mounting (without VPIS) 7. PDCOM Mounting 7.1 Checking environmental conditions and installation space 7.2 Hardware interfaces...
-
Page 3: Introduction
— 1. Introduction The installation manual contains instructions on Symbols how to install PDCOM. The manual describes The electrical warning icon indicates the procedures for mechanical and electrical presence of a hazard which could result installation. The chapters are set out in the order in in electrical shock. -
Page 4: Environmental Aspects
Part 5: Voltage detecting systems (VDS) electronic devices. All parts used in this product are recyclable. When disposing of PDCOM or its parts contact a local waste handler who is authorized and specialized in disposing of electronic waste. These handlers can... -
Page 5: Unpacking, Inspection And Storage
Storage Figure 1: Identification label on backplate If PDCOM is stored before installation, it must be kept in its original transport packaging in a dry and The Serial Number is an important traceability tool dust free place. Comply with the environmental for the user and for manufacturer. -
Page 6: Precondition For Pdcom Installation
PDCO M – INSTALLATION MANUAL — 4 Precondition for PDCOM installation • VPIS/VDS tested Checking environmental The following table shows which VPIS (also called as conditions and installation VIS) and VDS has been tested. space Coupling Nominal Voltage ABB ID number... -
Page 7: Pdcom Interface Mounting (With Vpis)
- The connector is standard DB9 straight-through • 1 connector for VPIS/VDS (J12) (Phoenix connector) • 1 connector for CAP divider (J11) Figure 2: PDCOM interface: connection to PDCOM, Dsub9 connector and PDCOM interface: connection to VIS, Phoenix connector The dimensions of PDCOM interface are the... - Page 8 PDCOM – INSTALLATION MANUAL — 5 PDCOM interface Mounting (with VPIS/VDS) Commercial code: 1VCF681000S0104 If the device is installed inside an enclosed cabinet, please check that there is enough space all round so that the connectors and cables can be fitted.
- Page 9 DISTRIBUTION SOLUTIONS Figure 5: Adapter cables Case 3: if adapter cables need to be longer than 3 centimeters a shielded wire must be used and the shield must be connected to the VPIS/VDS cables earth (see Figure 8 and Figure 10 for hearth connection). Figure 6: Shielded adapter cables...
- Page 10 PDCOM – INSTALLATION MANUAL — • Step 3: install the VIS interface: - Connect the 3 phases (see connector J11 in Figure 18). VPIS/VDS should connected in series, between the capacitor divider (4.1a) and the VPIS/VDS (4.1b). Figure 7: VIS interface connection with VPIS/VDS What is key with the grounding in general is to avoid ground loops.
- Page 11 VIS interface and connect the cable between the VIS interface and the PDCOM (5.2). Figure 11: PDCOM connections - Connect the ethernet cable 5.3 to the SWICOM or to the previous PDCOM if more than one is installed. • As a general note, the ground connection between the PDCOM, VIS interface and shielded cables should always be as short as possible.
-
Page 12: Pdcom Interface Mounting (Without Vpis)
PDCOM – INSTALLATION MANUAL — 6 PDCOM interface Mounting (without VPIS/VDS) Commercial code: 1VCF681000S0105 • Step 1: Refer to Capacitive divider installation • Step 2: Install the VIS interface: - connect the 3 phases. The VIS Interface should be connected to the capacitor divider (4.1a). The... - Page 13 VIS interface and the PDCOM (5.2). Figure 15: PDCOM connections - Connect the ethernet cable 5.3 to the SWICOM or to the previous PDCOM if more than one is installed. - The VIS interface must be the one dedicated with...
-
Page 14: Pdcom Mounting
Sufficient space is needed on top and in front to Unwanted transients must be eliminated allow access to wires and to enable maintenance (lightning protection). Comply with EMC and future modifications. requirements. The dimensions of PDCOM are the following: Figure 16: PDCOM dimensions... - Page 15 • 1 connector for multibus (J4 or J5) • 1 connector for sensor bus (J2) to connect to SWICOM, J3 to connect to other PDCOM with in/ out connection - The connector is standard RJ45 cable straight- through category 5 or 6 •...
- Page 16 PDCOM – INSTALLATION MANUAL — Electrical Diagrams for connections, 1VCD400305 The following scheme is when VIS is available: Figure 18: PDCOM electrical scheme with VIS The following scheme is when VIS is not available: Figure 19: PDCOM electrical scheme without VIS...
- Page 17 If the device is installed inside an enclosed cabinet, Step 1: Install the Power Supply (24Vdc) (5.1) please check that there is enough space all round so Step 2: Connect the cable coming from PDCOM that the connectors and cables can be fitted. interface (5.2)
-
Page 18: Connection
PDCOM use the SWICOM sensor bus that provides the interface for the sensors placed on the switchgear. PDCOM J2 connector shall have to be connected to the SWICOM P3 through a standard RJ45 cable straight-through category 5 or 6. -
Page 19: Removal, Repair And Replacement
9.4 Repairs During the product lifecycle, the time will come Contact the nearest ABB or representative for when PDCOM must be upgraded to a next consultation and instructions if the product generation. Although this will not be required until develops faults. -
Page 20: Installation Kit
PDCOM – INSTALLATION MANUAL — Installation Kit The PDCOM unit can be installed in at least two different places: In front of the low voltage compartment (following the procedure in chapter 4) In a metal-enclosed box (usually when the... -
Page 21: Accessories And Ordering Data
DISTRIBUTION SOLUTIONS — Accessories and ordering data Table 3: Device and sensors Item Order number PDCOM HV 1VCF681000S0103 PDCOM HV with VIS 1VCF681000S0104 PDCOM HV without VIS 1VCF681000S0105... -
Page 22: Glossary
PDCOM – INSTALLATION MANUAL — Glossary Current transformer Electromagnetic compatibility Human-machine interface International Electrotechnical Commission IEC 61850 International standard for substation communication and modeling Intelligent electronic device Liquid crystal display Liquid crystal polymer Light-emitting diode LHMI Local human-machine interface Polyamide Polybutylene terephthalate Personal computer;... - Page 23 DISTRIBUTION SOLUTIONS — Notes ..............
- Page 24 Your contact center: www.abb.com/contactcenters More service information: www.abb.com/service The data and illustrations are not binding. We reserve the right to modify the contents of this document without prior notice following technical and product developments. © Copyright 2020 ABB. All rights reserved.