Rice Lake 250-10-4 Operation Manual
Bariatric scale with handrail and chair seat
Hide thumbs
Also See for 250-10-4:
- Operation instructions manual (20 pages) ,
- Operation manual (20 pages)
Related Manuals for Rice Lake 250-10-4
Summary of Contents for Rice Lake 250-10-4
- Page 1 250-10-4 Bariatric Scale with Handrail and Chair Seat Software Version 11525 Operation Manual March 21, 2023 PN 151863 Rev E...
- Page 2 All information contained within this publication is, to the best of our knowledge, complete and accurate at the time of publication. Rice Lake Weighing Systems reserves the right to make changes to the technology, features, specifications and design of the equipment without notice.
- Page 3 March 21, 2023 Added assembly instructions Table i. Revision Letter History Technical training seminars are available through Rice Lake Weighing Systems. Course descriptions and dates can be viewed at www.ricelake.com/training or obtained by calling 715-234-9171 and asking for the training department.
-
Page 4: Table Of Contents
6.0 Specifications ............... . . 18 Rice Lake continually offers web-based video training on a growing selection of product-related topics at no cost. -
Page 5: Introduction
Introduction Introduction The 250-10-4 bariatric handrail scale with fold down chair seat is designed for weighing bariatrics and ensures sound, accurate weighing information. A non-skid platform paired with side rails assists persons who need extra support and safety. The fold down chair allows patients to sit down while being weighed. -
Page 6: Safety
Do not operate or work on this equipment unless this manual has been read and all instructions are understood. Failure to follow the instructions or heed the warnings could result in injury or death. Contact any Rice Lake Weighing Systems dealer for replacement manuals. -
Page 7: Assembly
Use caution while removing packaging and unpacking the scale. After unpacking, visually inspect the scale to ensure all components are included and undamaged. If parts were damaged in shipment, notify Rice Lake Weighing Systems and the shipper immediately. - Page 8 250-10-4 Bariatric Handrail Scale with Chair Seat 4. Use the supplied hex wrench to loosen the screw on both center rail hinges. 5. Raise the center rail to the upright position. 6. Tighten the screw. Screw Hex Wrench Figure 2-2. Center Rail in Down (left) and Up Position (right) 7.
-
Page 9: Adjusting Scale Feet
2.2.2 Unfold Platform Seat The 250-10-4 comes with a fold down seat for those patients who need to be weighed while seated. To unfold the seat, simply pull down on the seat bottom as shown in Figure 2-4. -
Page 10: Insert Batteries
An optional AC power adapter can be used when a power outlet is available. IMPORTANT: Only use power adapters supplied by or purchased from Rice Lake Weighing Systems. The use of a power adapter not from Rice Lake Weighing Systems voids the warranty. -
Page 11: Operation
Adjusts height input (0.5 in/0.5 cm) while in BMI mode Down Arrows Adjusts the value of the flashing digit/number Adjusts height input (0.5 in/0.5 cm) while in BMI mode Table 3-1. Key Functions © Rice Lake Weighing Systems ● All Rights Reserved... -
Page 12: Weighing
250-10-4 Bariatric Handrail Scale with Chair Seat Weighing Use the following steps to weigh. to turn on the scale. 0.0 appears on the display along with the ZERO annunciator. 1. Press 2. Place the patient on the scale. The patient’s weight is displayed, the LOCK annunciator is on and the indicator beeps to indicate the end of the weighing process. -
Page 13: Using The Body Mass Index (Bmi) Function
5. Press ENTER 6. The BMI value and BMI annunciator are shown on the display. Press to return to the Weighing mode and the CLEAR BMI function will be turned off. © Rice Lake Weighing Systems ● All Rights Reserved... -
Page 14: Troubleshooting
250-10-4 Bariatric Handrail Scale with Chair Seat Troubleshooting Refer to the following table to check and correct any failure before contacting service personnel. Symptom Possible Cause Corrective Action Scale does not turn on Dead batteries Replace batteries or connect to AC power... -
Page 15: Communication
The unit comes with an RS-232 port that enables weight data to be transmitted to other equipment, such as a computer or printer. The RS-232 cable with DB-9 connector (PN 100719) is available from Rice Lake Weighing Systems. That connection is shown in USB Connection section on the next page. -
Page 16: Usb Connection
250-10-4 Bariatric Handrail Scale with Chair Seat USB Connection The scale has the capability of connecting to a Windows computer (PC) using a USB cable (not included) and a terminal ® emulation program. A terminal emulation program allows the transfer of data between the scale and PC using a serial port. -
Page 17: Maintenance
• Clean all external surfaces with a clean, damp cloth or tissue. Mild soap and water solution may be used. Dry with a clean soft cloth • Do not immerse the scale into cleaning or other liquid solutions • Do not use Isopropyl alcohol or other solutions to clean the display surface © Rice Lake Weighing Systems ● All Rights Reserved... -
Page 18: Specifications
250-10-4 Bariatric Handrail Scale with Chair Seat Specifications Capacity 1,000 × 0.2 lb (450 × 0.1 kg) Platform Dimensions (W × L × H) 20 × 25 × 3 in Power 9 VDC, provided by six AA alkaline batteries (included) or AC adaptor (optional) - Page 20 © Rice Lake Weighing Systems Content subject to change without notice. 230 W. Coleman St. • Rice Lake, WI 54868 • USA U.S. 800-472-6703 • Canada/Mexico 800-321-6703 • International 715-234-9171 • Europe +31 (0)26 472 1319 March 21, 2023 PN 151863 Rev E...