Cartridge Filter, Removal, Cleaning, Re-Installation; Cleaning The Acrylic Surface; Safety Hard Cover - Hydropool 14IX Owner's Manual

CARTRIDGE FILTER
The cartridge should be cleaned every two to four weeks,
depending on the amount of use. Signs that the filter requires
cleaning include:
• Reduced jet power
• Hazy gray water
• Rattling noise in the pump or filter
• Heater not working
REMOVAL
1 Activate the STANDBY/DRAIN ASSIST mode.
2 Remove the filter cover and open the small, black air vent /
bleeder valve on the top of the filter lid.
3 Lift the Gray lock tab to disengage and turn the locking ring
counter clockwise.
4 Pull the filter lid upwards, and lift the cartridge element
straight up and out of filter housing.
CLEANING
5 With a garden hose and spray nozzle, hose off the cartridge
element, ensuring to carefully separate every pleat.
6 To remove collected lotions, body oils, etc. soak the car-
tridge in warm water and a filter cleaning/emulsifying com-
pound (available at your HYDROPOOL retailer).
7 A cleaning cylinder may be purchased from your HYDRO-
POOL Hot tub Retailer.
8 Rinse thoroughly and dry before replacing.
9 Hydropool recommends purchasing a spare filter cartridge
so that you always have a clean substitute ready to rotate.
10 After the element has dried - if necessary, lightly brush
between pleats with a fine paint-brush to remove remain-
ing dirt particles.
Do not use a wire brush or other devise
to clean cartridge element.
Do not put in dishwasher or washing ma-
chine.
RE-INSTALLATION
11 Place the cartridge filter back into the filter housing.
12 Replace the filter housing lid, pushing it down to seat, en-
suring that the lid o-ring does not become twisted.
13 Hydropool recommends that the lid o-ring be lubricated
with a non-petroleum based lubricant (ie. Silicone gel)
when it becomes dry. This will help to prevent twisting and
pinching as the lid is installed, and significantly increase
longevity of the o-ring.
14 Install the filter lock-ring, turning clockwise until the lock
tab snaps into place.
15 Close the air vent/bleeder valve.
16 Take the system out of STANDBY/DRAIN ASSIST mode.
17 When the pump starts circulating on low speed, it will be
necessary to release trapped air in the filter. Carefully
loosen the air vent/bleeder valve counter-clockwise until
there is the hissing sound of air escaping. Once there is a
steady stream of water, close the vent valve, ensuring that
the o-ring does not become pinched.
BUILT IN CHEMICAL
DISPENSER
CARTRIDGE FILTER
ELEMENT
FILTER HOUSING

CLEANING THE ACRYLIC SURFACE

The acrylic surface can be cleaned and polished using a soft
cloth and acrylic cleaner, available at your Hydropool retailer.
• Important: Do not use detergents - the
remaining residues will adversely affect
water chemistry, making it difficult to
maintain proper water balance
• Do Not use abrasive cleaners – damage
to the acrylic surface will occur.

SAFETY HARD COVER

When a swim spa is uncovered, over 90% of heat is lost from
the water surface. This evaporation also affects the chemical
balance and could create humidity problems indoors. HY-
DROPOOL Safety Hard Covers are engineered for maximum
thermal efficiency and appearance. They are hinged in the
middle for easier handling, and the zip fastener allows the
tapered foam inserts to be changed if damaged. The skirt of
the safety hard cover hugs the lip of the swim spa for a tight
fit. The handles are placed so that even one person can eas-
ily carry a large cover. The locks, with one part fastened to
the deck or skirt, prevent small children or animals from en-
tering the swim spa.
Do not drag the safety hard cover across the swim spa or
decking. Fold the cover first, then lift by the handles. Standing
on the hardcover could cause the tapered foam inserts to
crack, which will lead to water absorption.
NEVER LEAN OR STAND ON YOUR HARDCOVER.
The cover should be cleaned at least twice a year with a vinyl
moisturizer and protector.
36
LOCKING
RING
AIR VENT
VALVE
FILTER LID