Table of Contents
Advertisement
Toll Free: 1.800.465.2933
Fax: 905.565.6820
Email: info@hydropoolhottubs.com
www.hydropoolhottubs.com
Hydropool Inc.:
Tel: 905.565.6810
99399
HYDROPOOL
self-cleaning
hot tubs
Quick Start Guide
For complete instructions
please refer to the Owner's
Manual on CD
01/01/10 REV
1
Refer to Owner's Manual for complete details
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Hydropool Gold Series 40A
Summary of Contents for Hydropool Gold Series 40A
- Page 1 HYDROPOOL self-cleaning hot tubs Quick Start Guide For complete instructions please refer to the Owner’s Manual on CD Hydropool Inc.: Tel: 905.565.6810 Toll Free: 1.800.465.2933 Fax: 905.565.6820 Email: info@hydropoolhottubs.com www.hydropoolhottubs.com 01/01/10 REV 99399 Refer to Owner’s Manual for complete details...
-
Page 2: Table Of Contents
– r.c.D. installation - typical .........6 important electrical Safety hot tub Water Balance & routine maintenance ....7 Wire Size ................3 hydropool Self clean Series control Systems G.F.C.I./R.C.D. Application Guide For Self Clean – Silver & Gold Series .......9 Hydropool Self Clean Series ........3 Self Clean –... -
Page 3: Wire Size
G.f.c.i./r.c.D. application GuiDe for the circuit conductors supplying the equipment. hyDropool Self clean SerieS 7 At least two lugs marked “BONDING LUGS” are provided on the external surface or on the inside of the supply terminal box or compartment. -
Page 4: North America - Gfci Installation
north america – Gfci inStallation Important Note: Installation of the GFCI - Circuit Breaker, including ampere sizing and selection of conductor size and type, must be performed by a qualified electrician in accordance with the National Electrical Code, or the Canadian Electrical Code, and all Federal, State/Provincial and local codes and regulations in effect at the time of installation. -
Page 5: Filling, Checking And Starting Your Hot Tub
fillinG, checKinG anD StartinG your hot tuB FILLING • When adding water for the first time, the hot tub should be filled through the skimmer opening (helps to prevent air locks) using a standard garden hose. Fill the hot tub to the recommended level, approximately 19 mm (3/4“) from the top of the skimmer opening. -
Page 6: Europe - R.c.d. Installation - Typical
europe – r.c.D. inStallation - typical Important Note: Installation of the R.C.D. - Circuit Breaker, including ampere sizing and selection of conductor size and type, must be performed by a qualified electrician in accordance with National, Regional and Local Codes and Regulations in effect at the time of installation. House Breaker Box (Neutral) to hot tuB Support... -
Page 7: Hot Tub Water Balance & Routine Maintenance
Rinse thoroughly and, if possible, allow to dry handy in the event of an emergency. before re-installing. Hydropool recommends purchasing a • Keep chemicals out of children‘s reach second filter so that while the first is cleaning, the other •... - Page 8 See sections CHANGING 13 Hydropool recomends that the lid o-ring be lubricated THE HOT TUB WATER and DRAINING YOUR HOT TUB with a non-petroleum based lubricant (ie. Silicone gel) CLEANING THE SkIMMER bASkET when it becomes dry.
-
Page 9: Hydropool Self Clean Series Control Systems
Self clean SerieS control SyStemS north america/ europe HYDRoPooL SELF CLEAN – GoLD SERIES North America TEMPERATuRE CoNTRoL FuNCTIoNALITY AND ADJuSTMENT After you manually exit or the system automatically exits PRImING mODE, your hot tub will automatically heat to Europe the factory preset default temperature of 38˚C (100˚F) The... - Page 10 PuMP / JETS FuNCTIoN MoDE FuNCTIoN Press this pad to activate the pump A combination of keypads is used to change hot tub operation to either ‘STANDARD’, ‘ECONOMY’ or ‘SLEEP’ mode. 1st press – turns on low speed PRoGRAMMING MoDE FuNCTIoN 2nd press –...
-
Page 11: Limited & Luxury Edition
Self clean SerieS control SyStemS europe/north america HYDRoPooL SELF CLEAN – PLATINuM & LuxuRY EDITIoN PuMP PRIMING MoDE As soon as PRIMING MODE is indicated on the topside panel, push the left to start Pump 1 in low speed, then again to switch to high speed. - Page 12 To CHECk/CHANGE THE SET TEMPERATuRE PuMPS AuToMATIC TIME-ouT The last measured temperature is constantly P1 high speed, P2 & P3 – 15 minutes displayed on the topside control. When either of these pads P1 low speed – 4 hours. is pressed once, the display will show the set temperature. PuMP &...
- Page 13 FILTER CYCLES PROGRAM, FILTER 2 END TIME At this point will appear on the display Once the system clock time has been programmed, the system will automatically activate P1 low speed to filter the Adjust time as above water for 2 hours twice each day. During the filter cycle, the display will show FILTER 1 or FILTER 2.
- Page 14 LIquID CRYSTAL DISPLAY (LCD) STANDbY / DRAIN ASSIST Continually provides feedback on the The standby/drain assist feature stops the system from operating status of the hot tub. operating automatically, allowing for convenient filter Icons indicate various functions and cartridge removal and for safe draining of the hot tub. The programming information.
-
Page 15: Changing The Hot Tub Water
DRAINING YouR HoT Tub 19 Once fill is complete, remove the #10 rubber expansion HYDRoPooL ExCLuSIvE quICk-DRAIN™ & FILL plug from the bottom of the skimmer housing.* REFER To DIAGRAM 20 If the filter housing was opened to replace the cartridge... - Page 16 n o te S Refer to Owner’s Manual for complete details...
Need help?
Do you have a question about the Gold Series 40A and is the answer not in the manual?
Questions and answers