Maintenance; Troubleshooting; Technical Data - Flymo Contour Cordless 20V Li Operator's Manual

4. MAINTENANCE

DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v Wait for the trimmer line to stop and remove the battery
before you maintain the product.
v Cutting head continues to rotate after the trimmer has been
switched off. Keep fingers and hands clear of the line cutter
on leading edge of guard.
To clean the lawn trimmer [ Fig. V / W / X / Y ]:
DANGER! Risk of injury!
Risk of injury and risk of damage to the product.
v Do not clean the product with water or with a water jet
(in particular high-pressure water jet).
v Do not clean with chemicals including petrol or solvents.
Some can destroy critical plastic parts.
The airflow slots must always be clean.
After you have finished using your trimmer follow the procedure below:
1. Using a soft brush, clean around the inside of the safety guard,
the cutting head (V) and the motor housing air vents (W).
2. Remove the wheel by pressing one of the buttons. Clean the wheel (X)
and groove (Y) on the trimmer head with a soft brush.
3. Attach wheel as described in 2. ASSEMBLY To assemble the wheel.
4. Inspect the trimmer carefully, especially the parts of the cutting head.
5. If your trimmer is damaged in any way contact your local Husqvarna
service centre.
v Never use a damaged trimmer.
To clean the battery and the battery charger:
Make sure that the surface and the contacts of the battery and the battery
charger always are clean and dry before you connect the battery charger.
Do not use running water.
v Battery charger: Clean the contacts and the plastic parts with a soft
and dry cloth.
v Battery: Occasionally clean the ventilation slots and the terminals on
the battery using a soft brush that is clean and dry.
5. STORAGE
To put into storage:
The product must be stored away from children.
1. Remove the battery.
2. Fully charge the battery pack for 2.5 – 3 hours before winter storage.
Re-charge the battery pack every 3 to 4 months for a full 2.5 – 3 hour
charging period to top up the battery charge during winter storage.
Avoid extended storage without re-charge.
3. Clean the trimmer, the battery and the battery charger
(see 4. MAINTENANCE).
4. Allow the product to cool for at least 30 minutes before storing.
5. Store the trimmer, the battery and the battery charger in a dry,
enclosed and frost-free place.
Disposal:
(in accordance with RL2012/19/EC / S.I. 2013 No. 3113)
The product must not be disposed of to normal household
waste. It must be disposed of in line with local environmental
regulations.
IMPORTANT!
v Dispose of the product through or via your municipal recycling
collection centre.
Disposal of the battery:
The battery contains lithium-ion cells that should not be disposed
of with normal household waste at the end of its life.
Li-ion
IMPORTANT!
v Dispose of the batteries through or via your municipal recycling
collection centre.
8
42020-85.960.01.indd 8 42020-85.960.01.indd 8
1. Discharge the lithium-ion cells completely (contact the FLYMO Service).
2. Protect the contacts on the lithium-ion cells against short circuits.
3. Dispose of the lithium-ion cells properly.

6. TROUBLESHOOTING

DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v Wait for the trimmer line to stop and remove the battery
before you troubleshoot the product.
Problem Possible Cause
Line not feeding or Automatic line feed not
Line to short or working.
Trimmer vibrates
Line fed out and visible.
Line has been removed from
cleat.
Manual line feed not working.
Continuous clattering
Motor has not reached full
noise
speed before use.
Too much line has been
fed out.
The line cutter is missing from
the safety guard.
Line snaps continuously
The trimmer has not been
used correctly.
The line is jamming on the
spool.
Wheel stops turning
v Clean wheel and groove on trimmer head
(see 4. MAINTENANCE).
NOTE: For any other malfunctions please contact the
FLYMO service department. Repairs must only be done
by FLYMO service departments or specialist dealers
approved by FLYMO.

7. TECHNICAL DATA

Battery Lawn Trimmer Unit Value
Contour Cordless 20V Li
Cutting width cm 25
Speed of rotation of
rpm 9,000
cutting device
Cutting filament diameter
mm 1.5
Trimmer line supply
m 10
Trimmer line feed automatically / manually
Weight (without Battery) kg 2.5
Sound pressure level L 73.4
1)
dB (A)
pA
Uncertainty k 3.0
pA
Sound power level L :
2)
WA
measured / guaranteed 88 / 92
dB (A)
Uncertainty k 4.0
WA
Hand / arm vibration a 1.607
1)
m/s
2
vhw
Uncertainty k 1.5
vhw
Measuring process complying with: EN 50636-2-91
1)
NOTE: The stated vibration emission value has been measured according to
a standardized test procedure and can be used for comparison of one electric
power tool with another. It can also be used for preliminary evaluation of expo-
sure. The vibration emission value can vary during actual use of the electric power tool.
Remedy
v Manually feed out line
see 3. OPERATION
To manually feed the nylon line.
v Remove cap and spool,
free line and re-fit spool and
cap, see 3. OPERATION
Cutting head.
v The line may be jammed on
the spool. Rewind line to
remove crossed loops.
Check that line is in correct
section of spool.
v Allow the motor to reach full
speed before use.
v See 3. OPERATION
To manually feed the nylon line.
v Contact your local approved
Service Centre or Husqvarna
Customer Service.
v Only use tip of nylon line to
trim, see 3. OPERATION
How to trim and How to edge.
v Rewind the line on the spool,
if symptoms still persist,
change spool and line.
RL 2000/14/EC / S.I. 2001 No.1701
2)
20.09.21 11:11 20.09.21 11:11