Operation; Maintenance - Flymo EasiCut 450 Operator's Manual

Avoid contact with the oil of the blade, allergic reaction is possible.
Only work in the daylight or when visibility is good.
Check your product before each use. Always visually inspect your Hedge Trim-
mer before each use. Check that the ventilation slots are not obstructed in any
way.
If the product gets hot whilst in operation, allow it to cool down before storage.
Warning! When wearing hearing protection, and due to the noise produced by
the product, the operator may not notice persons approaching.
Always wear suitable clothing, protective gloves, and stout shoes.
Always ensure that you have a secure foothold whilst working.
2. ASSEMBLY
DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v Remove the battery and slide the protective cover over the
blade before you assemble the product.
To assemble the front handle [ Fig. A1 ]:
1. Push the front handle (1) into the slot in the hedge trimmer.
Make sure that the front handle
2. Tighten both already located screws
Make sure that the screws
can be completely pushed.

3. OPERATION

DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v Wait for the blade to stop, remove the battery and slide the
protective cover over the blade before you adjust or transport
the product.
To charge the battery [ Fig. O1 / O2 / O3 ]:
CAUTION!
v Note the mains voltage! The voltage of the power source must
match the voltage specified on the rating plate of the charger.
For the FLYMO Battery Hedge Trimmer Art. 970543301 / 970543701
there is no battery and no charger in the scope of delivery.
Thanks to the intelligent charging process, the charge condition of the
battery is automatically detected and then charged up with the optimal
charge current depending on battery temperature and voltage.
In this way, the battery is treated with care and remains permanently fully
charged when it is stored in the charger.
(A)
1. Push the locking button
(D)
holder .
2. Connect the battery charger
3. Slide the battery charger (C)
When the battery charge indicator
the battery is being charged.
When the battery charge indicator
permanently green the battery is completely charged
(Charging time see 7. TECHNICAL DATA).
4. Examine the charge status regularly while you charge.
(B)
5. When the battery is completely charged, you can disconnect the
battery (B) from the charger
Meaning of the Indication Elements:
Indication on the charger [ Fig. O3 ]:
Flashing of the Battery The charging procedure is indicated by flashing of the battery charge
(Lc) (Lc)
Charge Indicator indicator
Note: The charging procedure is only possible when the battery
temperature is within the allowable charging temperature range,
see 7. TECHNICAL DATA.
Continuous Lighting Continuous lighting of the battery charge indicator
of the Battery the battery is fully charged or that the temperature of the battery is
(Lc)
Charge Indicator not within the allowable charging temperature range and can therefore
not be charged.
When the battery is not inserted, continuous lighting of the battery
charge indicator
socket outlet and that the battery charger is ready for operation.
6
32450-85.960.01.indd 6 32450-85.960.01.indd 6
(1) is completely in place.
(2) .
(2) are tightened and the start button
(B)
and remove the battery from the battery
(C)
into a mains socket.
onto the battery (B) .
(Lc) at the charger flashes green
(Lc) at the charger illuminates
(C) .
.
(Lc) indicates that
(Lc)
indicates that the mains plug is inserted in the
Battery charge status indication
After starting the product, the battery charge status indication
is displayed for 5 seconds.
Battery charge status
67 – 100 % charged
34 – 66 % charged
11 – 33 % charged
0 – 10 % charged
If the LED (L1) flashes green, the battery must be charged.
If the error LED (Wp) is illuminated or flashing, see 6. TROUBLESHOOTING.
Work positions:
The hedge trimmer can be operated in 3 positions.
– Side trimming [ Fig. O5 ]
– High trimming [ Fig. O6 ]
– Low trimming [ Fig. O7 ]
To start the hedge trimmer [ Fig. O1 /O8 ]:
DANGER! Risk of injury!
Risk of injury if the product does not stop when you
release the start levers.
(3)
v Do not bypass the safety devices or switches. For example
do not attach the start levers to the handle.
To start:
The product is provided with a two-handed safety device (2 start
levers) to prevent the product from being turned on by accident.
1. Put the battery (B) into the battery holder
2. Remove the protective cover from the blade.
3. Hold the front handle
4. Hold the main handle
lever (5) .
The hedge trimmer starts and the battery charge status indication
is displayed for 5 seconds.
To stop:
1. Release the two start levers
The hedge trimmer stops.
2. Slide the protective cover over the blade.
3. Push the locking button
(D)
battery holder .

4. MAINTENANCE

DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v Wait for the blade to stop, remove the battery and slide
the protective cover over the blade before you maintain the
product.
To clean the Hedge Trimmer [ Fig. M1 ]:
DANGER! Risk of injury!
Risk of injury and risk of damage to the product.
v Do not clean the product with water or with a water jet
(in particular high-pressure water jet).
v Do not clean with chemicals including petrol or solvents.
Some can destroy critical plastic parts.
The airflow slots must always be clean.
1. Clean the hedge trimmer with a damp cloth.
2. Clean the airflow slots
3. Lubricate the blade with a low viscosity oil.
Avoid contact with the plastic parts.
To clean the battery and the battery charger:
Make sure that the surface and the contacts of the battery and the battery
charger always are clean and dry before you connect the battery charger.
Do not use running water.
(P) on the product [ Fig. O4 / O8 ]:
Battery charge status indication
(L1) (L2) (L3)
, and illuminate green
(L1) and (L2) illuminate green
(L1)
illuminates green
(L1) flashes green
(D) until it audibly engages.
(1) with one hand and pull the front start lever
(4)
with the other hand and pull the rear start
(3) (5)
/ .
(A) and remove the battery (B) from the
(6) with a soft brush (do not use a screwdriver).
(P)
(3) .
(P)
06.10.21 10:48 06.10.21 10:48