Operation; Troubleshooting; Maintenance - Flymo EasiCut 610XT Operator's Manual

6. A 13 amp fuse must be fitted to the Mains Plug.
7. The normal plug fuse and household fuse only protect the electrical
equipment and are not a safeguard against electrocution.
If your product is hard wired i. e. non-detachable mains electric cable,
a conversion kit and extension cable is available from all Approved
Service Centres which can be found in your local Yellow Pages.

3. OPERATION

To start your hedge trimmer:
1. Remove the blade cover (A).
2. There are three switch levers fitted to your Hedgetrimmer.
3. To start, push forward the lock-off button (B1), squeeze the main
switch lever (B2), release lock-off button.
4. Main switch lever (B2) and one other need to be held in the operating
position (B3 or C1) for the product to start.
To stop your hedge trimmer:
• Move hedge trimmer away from cutting area before stopping.
v To stop, release any switch lever (D).
How to use your hedge trimmer:
1. Inspect area to be cut before each use –remove objects which can be
thrown or become entangled in the cutting blades.
2. Always keep the hedge trimmer in front of yourbody. Hold handle firmly
with both hands andstand in a secure and stable position.
3. Allow the cutting blades to reach full speed before entering the material
to be cut.
4. Always work going away from people and solid objects such as walls,
large stones, trees, vehicles etc.
5. If blade stalls, immediately stop the hedgetrimmer. Disconnect the
hedge trimmer from the power source and clear jammed debris from
the cutting blades. Inspect blades and repair or replace as needed.
Top cutting:
Use a wide sweeping motion (E). A slight downward tilt of the cutting
blades in the direction of motion gives the best cutting results.
Side cutting:
When trimming the sides of the hedge, begin at the bottom and cut
upwards (F), tapering the hedge inward at the top. This shape will expose
more of the hedge, resulting in more uniformed growth.

4. MAINTENANCE

WARNING!
Disconnect from the mains electricity supply, before attempting
any maintenance oradjustment.
Cleaning (G):
1. Using a soft brush – remove debris from all air intakes and cutting
blade.
2. Wipe over surface of your hedge trimmer witha dry cloth.
IMPORTANT!
v Never use water for cleaning your hedgetrimmer.
v Do not clean with chemicals, including petrol, or solvents –
some can destroy critical plastic parts.
Lubricating the cutting blade:
For easier operation and longer life, lubricate the cutter blades before and
after use. Apply the oil so that it runs between the two blades (G).
Service Recommendations:
1. We strongly recommend that your product is serviced at least every
twelve months, more often in a professional application.
2. Always use genuine Flymo Spare Parts.
3. Pre-packed spares are available from most Flymo approved stockists.
4. Your product is uniquely identified by a silver and black product rating
label.
6
31610-85.960.01.indd 6 31610-85.960.01.indd 6
5. If you have a problem with your machine contact your local Approved
Service Centre ensuring you have full details of your product as descri-
bed on the product rating label.
6. Should it be necessaryforworkto be carried out by your Service Centre,
it is important to take your complete machine including cable and any
extension cables used.
A network of specialist dealers can be found in your local Yellow Pages.
To obtain service on your product simply telephone or visit your local
Service Centre. Should you require service under the terms of our guaran-
tee the Service Centre will require proof of purchase. All of the centres
listed stock genuine Flymo Spare Parts. NOTE: Our Service Repairers act
on their own behalf and are not empowered to commit or legally bind
Husqvarna UK Ltd. in any manner whatsoever.
5. STORAGE
At the end of the cutting season:
1. Clean your hedge trimmer thoroughly.
2. Check that all nuts and bolts are secure.
3. Visually inspect the hedge trimmer for any worn or damaged parts,
contact your local Service Centre if any parts require replacement.
To store your hedge trimmer:
• Ensure the blade cover is fitted before storage.
• Store in a dry place where your hedge trimmer is protected from
damage.

6. TROUBLESHOOTING

Fails to Operate:
1. Is the Power Turned On?
2. Check the fuse in the plug, if blown replace.
3. Fuse continues to blow?
Immediately disconnect from the mains electricity supply and consult
your local approved Service Centre.
Cutting blade stops under load:
1. Cut at a slower pace.
2. If cutting blade still stops under load?
Disconnect from the mains electricity supply and consult your local
approved Service Centre.
Fails to stop when one switch lever is released:
v Immediately disconnect from the mains electricity supply
and consult your local approved Service Centre.
Poor cut quality:
1. Ensure the product is being used correctly (see How to use your hedge
trimmer).
2. Ensure blades are free from trapped debris.
3. Damaged Blades?
Immediately disconnect from the mainselectricity supply and consult
your local approved Service Centre.
Excessive Vibration:
v Immediately disconnect from the mains electricity supply and consult
your local approved Service Centre.
7. DISPOSAL
(in accordance with RL2012/19/EC / S.I. 2013 No. 3113)
• Awareness of the environment must be considered when disposing of
'end-of-life' product.
• If necessary, contact your local authority for disposal information.
The symbol on the product or on its packaging indicates that
this product may not be treated as household waste. Instead it
shall be handed over to the applicable collection point for the
recycling of electrical and electronic equipment. By ensuring this product
is disposed of correctly, you will help prevent potential negative conse-
quences for the environment and human health, which could otherwise
be caused by inappropriate waste handling of this product. For more
07.09.21 11:02 07.09.21 11:02