DeWalt XR DCD1623 Original Instructions Manual page 37

• Always place the machine on a surface that is clear of
shavings, chips, swarf and surface dirt.
• Keep the magnet clean and free of debris and swarf.
• Do not turn on the machine until it has been mounted and
installed according to these instructions.
• Do not turn on the machine before having checked that
the magnetic stand has been tightened firmly to the
mounting surface.
• Adjust the table so cutter does not extend into the workpiece
before drilling. Do not perform any design, assembly or
construction activities on the workpiece while the machine is
turned on.
• Before turning on the machine, make sure the accessory has
been mounted correctly.
• Always use the recommended speed for the accessories and
the material.
• Do not use the machine on the same workpiece on which
electric welders are being used.
• Use only an appropriate cutting fluid. Use a general metal
cutting coolant diluted with water.
• Do not use liquid cutting fluids while drilling vertically
or overhead. Dip the cutter in cutting paste or apply an
appropriate spray for these applications.
• Do not pour cutting fluid into the reservoir while it is mounted
in the bracket. Do not allow cutting fluid to enter the
drill motor.
• Before use, ensure movable chuck guard operates properly.
• Ensure that metal chips or resinous residue cannot lead to
blockage of the function.
• In case of jammed cutter disconnect the machine from the
power supply, remove the reason for the jam before turning on
the machine again.
Residual Risks
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual risks
cannot be avoided. These are:
• Impairment of hearing.
• Risk of personal injury due to flying particles.
• Risk of burns due to accessories becoming hot
during operation.
• Risk of personal injury due to prolonged use.
SAVE THESE INSTRUCTIONS
Chargers
D WALT chargers require no adjustment and are designed to be
e
as easy as possible to operate.
Electrical Safety
The electric motor has been designed for one voltage only.
Always check that the battery pack voltage corresponds to the
voltage on the rating plate. Also make sure that the voltage of
your charger corresponds to that of your mains.
i
Your D WALTcharger is double insulated in
e
accordance with EN60335; therefore no earth wire
is required.
If the supply cord is damaged, it must be replaced only by
D WALT or an authorised service organisation.
e
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in the plug.
• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be made to the
earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 3 A.
Using an Extension Cable
An extension cord should not be used unless absolutely
necessary. Use an approved extension cable suitable for the
power input of your charger (see Technical Data). The minimum
conductor size is 1 mm ; the maximum length is 30 m.
2
When using a cable reel, always unwind the cable completely.
Important Safety Instructions for All Battery Chargers
SAVE THESE INSTRUCTIONS: This manual contains important
safety and operating instructions for compatible battery
chargers (refer to Technical Data).
• Before using charger, read all instructions and cautionary
markings on charger, battery pack, and product using
battery pack.

WARNING: Shock hazard. Do not allow any liquid to get
inside charger. Electric shock may result.

WARNING: We recommend the use of a residual current
device with a residual current rating of 30mA or less.

CAUTION: Burn hazard. To reduce the risk of injury,
charge only D WALT rechargeable batteries. Other types of
e
batteries may burst causing personal injury and damage.

CAUTION: Children should be supervised to ensure that
they do not play with the appliance.
NOTICE: Under certain conditions, with the charger
plugged into the power supply, the exposed charging
contacts inside the charger can be shorted by foreign
material. Foreign materials of a conductive nature such
as, but not limited to, steel wool, aluminum foil or any
buildup of metallic particles should be kept away from
charger cavities. Always unplug the charger from the
power supply when there is no battery pack in the cavity.
Unplug charger before attempting to clean.
• DO NOT attempt to charge the battery pack with any
chargers other than the ones in this manual. The charger
and battery pack are specifically designed to work together.
These chargers are not intended for any uses other than
•
charging D WALT rechargeable batteries. Any other uses
e
may result in risk of fire, electric shock or electrocution.
• Do not expose charger to rain or snow.
EnGLIsH
35