English MAGNETIC DRILL PRESS DCD1623 Congratulations! EC‑Declaration of Conformity You have chosen a D WALT tool. Years of experience, thorough Machinery Directive product development and innovation make D WALT one of the most reliable partners for professional power tool users. Technical Data Magnetic Drill Press DCD1623 DCD1623...
English Batteries Chargers/Charge Times (Minutes)*** Weight (kg) DCB104 DCB107 DCB112 DCB113 DCB115 DCB116 DCB117 DCB118 DCB132 DCB119 Cat # DCB547G 18/54 9.0/3.0 1.46 135* 110* 135* DCB184G 0.62 75/50** 75/60** 75/50** 75/50** *Date code 201811475B or later **Date code 201536 or later **Battery charge times matrix provided for guidance only;...
Page 9
English source and/or battery pack, picking up or carrying surfaces do not allow for safe handling and control of the the tool. Carrying power tools with your finger on the tool in unexpected situations. switch or energising power tools that have the switch on 5) Battery Tool Use and Care invites accidents.
English • Always place the machine on a surface that is clear of Your D WALTcharger is double insulated in shavings, chips, swarf and surface dirt. accordance with EN60335; therefore no earth wire is required. • Keep the magnet clean and free of debris and swarf. •...
English • Pull by plug rather than cord when disconnecting Charge Indicators charger. This will reduce risk of damage to electric plug Charging and cord. Make sure that cord is located so that it will not be • Fully Charged stepped on, tripped over, or otherwise subjected to damage or stress.
English cloth or soft non‑metallic brush. Do not use water or any the battery pack in aprons, pockets, tool boxes, product kit cleaning solutions. Never let any liquid get inside the tool; boxes, drawers, etc., with loose nails, screws, keys, etc. never immerse any part of the tool into a liquid.
English Transport Mode: When the cap is attached to the FLEXVOLT Discard the battery pack with due care for battery, the battery is in Transport mode. Keep the cap the environment. for shipping. When in Transport mode, strings Charge battery packs only with designated D WALT of cells are electrically chargers.
English unless they are supervised by a person responsible for their Wear eye protection safety. Children should never be left alone with this product. ASSEMBLY AND ADJUSTMENTS Visible radiation. Do not stare into light. WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect battery pack Do not use this tool if you or any bystanders have a before making any adjustments or removing/ cardiac pacemaker or other medical implants.
Page 15
English WARNING: Do not allow cutting fluid to enter WARNING: Never attach the safety chain through the the battery port or come in contact with the carry handle. battery pack. Feed the provided safety chain through the safety chain 26 nOTE: If battery comes in contact with cutting fluid wipe opening ...
English 1. Press in the gear selector button 32 and rotate the gear WARNING: To reduce the risk of serious personal selector dial into the desired mode. injury, turn tool off and disconnect battery pack 5 before making any adjustments or removing/ 2.
Page 17
English Prior to operation extremely hot and cause burns to the skin. Ensure nobody is in the work area where the metal core is ejected. WARNING: Inspect the chain before each use, for wear or Drilling Conditions damage. Replace if necessary. Try a few simple projects using scrap material until you develop The ease with which material can be drilled is dependent a “feel”...
English Rechargeable Battery Pack Tool Connect™ Chip (Fig. L) Optional Accessory This long life battery pack must be recharged when it fails to produce sufficient power on jobs which were easily done before. At the end WARNING: To reduce the risk of serious personal of its technical life, discard it with due care for our environment: injury, turn unit off and remove the battery pack before making any adjustments or removing/...
Page 19
English Speed (RPM) and Drill Settings (with 9Ah pack) Cutter Size Mild Steel Iron Plate 600–1000 RPM 800–1200 RPM 14 mm–16 mm High Gear, Speed 4–5 High Gear, Speed 5 480–800 RPM 640–960 RPM 16 mm–21 mm High Gear, Speed 3–5 High Gear, Speed 4–5 400–660 RPM 530–800 RPM...
Page 20
Belgique et WALT ‑ Belgium BVBA Tel: NL 32 15 47 37 63 www.dewalt.be luxembourg België en luxemburg enduser.BE@sBDinc.com Egide Walschaertsstraat 16 Tel: FR 32 15 47 37 64 2800 Mechelen Fax: 32 15 47 37 99 Danmark WALT (Stanley Black&Decker AS)