Quick-Start Guide
LAMP DIMMER
For Models:
LampLinc
LampLinc
Your new Lamp Dimmer allows you to dim and remotely control any lamp in your
home at the touch of a button.
N N e e e e d d H H e e l l p p ? ? F F o o r r a a s s s s i i s s t t a a n n c c e e c c a a l l l l y y o o u u r r f f r r i i e e n n d d l l y y
s s u u p p p p o o r r t t p p e e r r s s o o n n @ @ 8 8 6 6 6 6 - - 2 2 4 4 3 3 - - 8 8 0 0 1 1 8 8
Installing Your Lamp Dimmer
S S t t e e p p 1 1 . .
Two Signal Enhancers (SignaLinc
S S t t e e p p 2 2 . .
Plug your lamp into the outlet at the b b o o t t t t o o m m of the Lamp Dimmer (labeled "Controlled").
S S t t e e p p 3 3 . .
Plug your Lamp Dimmer into an unswitched wall outlet.
S S t t e e p p 4 4 . .
If lamp is off, t t u u r r n n i i t t o o n n . .
S S t t e e p p 5 5 . .
Select the INSTEON Controller you would like to use and set it to Linking Mode. Refer to your INSTEON
Controller's User's Guide for detailed instructions.
N N O O T T E E : : The following will work for most INSTEON Controllers.
• On the INSTEON Controller, choose the ON/OFF Button Pair you want to use for controlling your Lamp Dimmer.
• Set the INSTEON Controller to Linking Mode by pressing and holding the ON Button of the pair for 10 seconds.
S S t t e e p p 6 6 . .
Press and hold the black Set Button on the Lamp Dimmer for 3 seconds. The lamp will blink twice quickly on
successful linking and the Status LED will turn solid. The Status LED will continue to blink if linking is unsuccessful
Depending on the INSTEON Controller, you have about 4 minutes to perform this step before setup mode times out
automatically.
Congratulations! You can now dim and remotely control your lamp.
Notes
•
The Lamp Dimmer can be used with any incandescent lamp of 300 watts or less (minimum 10 watts) and should not be used with
halogen or fluorescent lighting.
• To reset the Lamp Dimmer to its original factory settings, unplug it from the wall outlet and wait 10 seconds. Press and hold its SET
button, plug it back in, continue holding the SET button for 3 seconds and release. After several seconds, the Status LED will turn on,
indicating a reset is complete.
• The advanced User's Guide can be found at w w w w w w . . s s m m a a r r t t h h o o m m e e . . c c o o m m / / 2 2 4 4 5 5 6 6 d d 3 3 . . h h t t m m l l and w w w w w w . . s s m m a a r r t t h h o o m m e e . . c c o o m m / / 2 2 4 4 5 5 6 6 d d 2 2 . . h h t t m m l l . .
TM
V2 2-pin (#2456D2)
TM
V2 3-pin (#2456D3) -
TM
RF #2442) m m u u s s t t be installed if your home does not already have them.
Pass-through
pictured
Outlet
Controlled
Outlet
HINTS
• Do not use an outlet controlled by
a switch
• Be sure to leave the lamp's local
switch in the on position
• Use to control incandescent
bulbs only.
Set Button
Status LED