Table of Contents
Advertisement
Quick Links
INSTALLATION &
OPERATING INSTRUCTIONS
Instructions and notes for installation and operation
3T-MOTORS Shutter / Awning motors 12V
with mechanical limit switches
Motor type 3T45-20/12V
Motor type 3T35-13/12V
(Für Wellen ab 60 mm)
(Für Wellen ab 40 mm)
Solar panel SP50
with integrated battery &
Radio receiver
Attention:
It is important for the safety of persons
to follow these instructions.
Keep these instructions for future reference.
www.3t-components.de
|
WEEE-Reg.-Nr.: DE 77028333
Motor type 3T45-50/12V
(Für Rundwellen ab 63 mm)
INTELLIGENT
DRIVES &
CONTROLS
FOR SHUTTERS
AND AWNINGS
Advertisement
Table of Contents
Related Manuals for 3T-Components 3T-MOTORS 3T45-20
Summary of Contents for 3T-Components 3T-MOTORS 3T45-20
- Page 1 (Für Wellen ab 40 mm) (Für Rundwellen ab 63 mm) Solar panel SP50 with integrated battery & Radio receiver Attention: It is important for the safety of persons to follow these instructions. Keep these instructions for future reference. www.3t-components.de WEEE-Reg.-Nr.: DE 77028333...
-
Page 2: Table Of Contents
All contents of these instructions, in particular texts, photographs and graphics, are protected by copyright. Unless expressly indicated otherwise, the copyright is held by 3T-Components GmbH & Co. KG. Please ask us if you wish to use the contents of this document. -
Page 3: Safety Instructions
SAFETY INSTRUCTIONS Please read these important safety instructions before commissioning! Incorrect installation can cause serious personal injury and damage to property. The warranty claim expires in case of non-observance of this user information with all contained notes and regulations. In case of non-observance of these instructions, the manufacturer or supplier shall not be liable for any personal injury or property damage incurred. GENERAL SAFETY INSTRUCTIONS WARNING: Important safety instructions. -
Page 4: Function Overview 3T45/12V / 3T35/12V
FUNCTION OVERVIEW 3T45/12V / 3T35/12V SCOPE OF DELIVERY – MOTOR TYPE 3T45/12V SCOPE OF DELIVERY – MOTOR TYPE 3T35/12V Motor Motor Limit switch adapter Limit switch adapter Shaft adapter Shaft adapter Connection cable 3 meters Connection cable 3 meters Adjustment pin Adjustment pin Universal bearing &... -
Page 5: Function Overview Solar Panel Sp50
FUNCTION OVERVIEW SOLAR PANEL SP50 Before startup Remove cover and charge internal battery via: Micro USB cable 5 V (Micro USB B connector) Open cover Micro USB port 5 V Connect micro USB cable Press program button > LED flashes green > Battery is charging Sunlight Solar module with integrated battery and •... -
Page 6: Programming
PROGRAMMING The internal battery must be charged before programming. Perform programming before mounting the motor and solar module. One transmitter can control up to 20 solar modules. Receiver stores a maximum of 20 transmitters (channels). Connect the shutter motor to the SP50 solar module: Slide the rotary lock of the SP50 solar module connection to the rear. -
Page 7: Pairing Another Transmitter
PROGRAMMING Change direction of rotation Programming (pressing the buttons) must be carried out within 10 seconds. Otherwise the system returns to its original state. of radio motor: Tubular motor LED indicator starts 2 x flashes 2 x Direction of rotation Press and hold program Release is changed... -
Page 8: Reset To Factory Settings
PROGRAMMING Delete all paired transmitters Tubular motor starts 1 x, LED indicator Tubular motor starts 1 x, LED indicator flashes 1 x flashes 1 x LED indicator flashes 4 x All transmitters are deleted 1 x Press button 1 x Press 1 x Press button P2 / Set Up Stop-button... -
Page 9: Installation Notes
INSTALLATION NOTES Before installation, all non-essential electrical wiring must be removed, all mechanisms that are not necessary for motorized operation must be deactivated. Do not expose the tubular motor to crushing, impact, falling or contact with any liquids. • Do not punch holes in the entire length of the tube (motor casing) or attach screws to it. Please use suitable suspension springs to fasten the roller shutter curtain to the roller shutter shaft. -
Page 10: Installation Instructions
INSTALLATION INSTRUCTIONS Please note: The motor can be installed on the right-hand side as well as on the left-hand side. • If the direction of rotation is reversed, please exchange the wires for the up and down direction. The setting of the end positions is only possible in the installed state (motor in shutter shaft). •... - Page 11 INSTALLATION INSTRUCTIONS Motor type 3T45-20/12V Motor type 3T35-13/12V Installation with universal bearing or cover cap bearing Installation with universal bearing or clip bearing Universal bearing Cover cap bearing Universal bearing clip bearing Installation with universal bearing: Installation with universal bearing: Push the motor with the square into the opening of the bearing Push the motor with the square into the opening of the bearing •...
-
Page 12: Remove Shutter Shaft
INSTALLATION INSTRUCTIONS Remove shutter shaft: Lower the roller shutter. • Open the cover of the roller shutter box. • Release the suspension springs from the roller shutter shaft. • Lift roller shutter shaft incl. ball bearing out of the holder. •... - Page 13 INSTALLATION INSTRUCTIONS On the opposite side of the motor, push the roller capsule out of the roller shutter shaft until it fits into the ball bearing inserted in the wall bearing. • Fix roller capsule to roller shutter shaft with self-tapping screw. Position the screw at a punched hole. This prevents the screw from slipping. •...
-
Page 14: Setting The End Positions
INSTALLATION INSTRUCTIONS Setting the end positions: Explanation of the limit switch screws There are 2 limit switch screws on the motor head. One limit switch screw is responsible for the upper end position, the other for the lower end position. The end positions can be adjusted by turning the limit switch screws with the adjustment pin. - Page 15 INSTALLATION INSTRUCTIONS Special case: Roller shutter rolls down in front of motor + shaft If the roller shutter curtain rolls in front of the motor and shaft, the responsibilities of the limit switch screws for the upper and lower end positions are reversed. See illustration of left-right installation on page 14: upper end position >...
- Page 16 INSTALLATION INSTRUCTIONS MOUNTING INSTRUCTIONS FOR 3T-MOTORS MINI-TUBE MOTORS MOTOR TYPE 3T35/12V Use proper suspension springs: To fasten the roller shutter curtain to the roller shutter shaft, please be sure to use • suitable suspension springs for motor operation. These special mini suspension springs only protrude approx.
- Page 17 INSTALLATION INSTRUCTIONS INSTALLATION AWNING MOTOR Preparation: Attention: Screw in awning & secure with straps or ropes. • Awning arms are under strong tension! Remove awning from wall bracket & place on safe surface. • Prepare motor for installation: Slide limit switch adapter flush against motor head. >...
- Page 18 INSTALLATION INSTRUCTIONS Slide the side bearing with universal bearing onto the support tube & fasten. > fig. 3.9 • Ensure that the motor square spigot is properly engaged in the universal bearing. > fig. 3.10 • Secure the motor square spigot with the supplied cotter pin. >...
- Page 19 INSTALLATION INSTRUCTIONS Setting the end positions: Explanation of the limit switch screws There are 2 limit switch screws on the motor head. One limit switch screw is responsible for the upper end position, the other for the lower end position. The end positions can be adjusted by turning the limit switch screws with the adjustment pin.
- Page 20 INSTALLATION INSTRUCTIONS 1. Setting the position „EXTEND” Adjustment pin is required Set the switch to „EXTEND”, awning moves OUT. • Run the tubular motor in the „EXTEND” direction until the end switch-off occurs. • If the motor is to continue moving, turn the adjustment pin on the „EXTEND” limit switch screw in the PLUS direction until the desired position is reached. •...
-
Page 21: Troubleshooting
TROUBLESHOOTING WHAT TO DO WHEN ..the motor does not run? Mains voltage is missing. • Check correct connection of the control (switch or timer). • ... the motor is running in the wrong direction? Swap the two wires for the direction of rotation (brown + black). •... -
Page 22: 3T Components Gmbh & Co. Kg
EU Konformitätserklärung Wir, die Firma 3T Components GmbH & Co. KG Bahnhofstr. 34 55578 Wallertheim Deutschland erklären in alleiniger Verantwortung, dass das weiter unten genannte Produkt Geräteart: Rohrmotor mit mechanischen Endschaltern Modell Artikelnummer 3T35-13/12V 601, 604 3T45-20/12V 600, 603 3T45-50/12V 602, 607 die grundlegenden Anforderungen der aufgeführten EG/EU-Richtlinien erfüllt: 2006/42/EG... - Page 23 OPTIONAL ACCESSORIES TUBULAR MOTORS ANTI-LIFT DEVICE | SHUTTER SHAFTS | ROLLER CAPSULE | SUSPENSION SPRINGS | BALL BEARINGS OCTOCLICK Anti-lift device 2-link / 2,5-link Burglar-resistant • The pushing up of a closed motorized roller shutter is prevented • For tubular motors with electronic or mechanical limit switching •...
-
Page 24: Email: Info@3T-Components.de
Social Media Links Info, news and tips on roller shutters, awnings, smart home and more: www.facebook.com/3TComponents bit.ly/youtube-3TComponents www.instagram.com/3tcomponents twitter.com/3TComponents 3T-Components GmbH & Co. KG Bahnhofstr. 34 55578 Wallertheim Email: info@3t-components.de Tel: +49 (0) 6732-600 03 69 Fax: +49 (0) 6732-600 54 30 www.3t-components.de...