Table of Contents
Advertisement
Quick Links
INSTALLATION &
OPERATING INSTRUCTIONS
Instructions and notes for installation and operation
3T-MOTORS Shutter motors
with obstacle detection and electronic limit switches
Motor type 3T45-E
(For shafts from 60 mm)
3T45-10E
3T45-20E
3T45-30E
3T45-40E
Attention:
It is important for the safety of persons
to follow these instructions.
Keep these instructions for future reference.
www.3t-components.de
|
WEEE-Reg.-Nr.: DE 77028333
INTELLIGENT
DRIVES &
CONTROLS
FOR SHUTTERS
AND AWNINGS
Advertisement
Table of Contents
Related Manuals for 3T-Components 3T-MOTORS 3T45-E
Summary of Contents for 3T-Components 3T-MOTORS 3T45-E
- Page 1 Motor type 3T45-E (For shafts from 60 mm) 3T45-10E 3T45-20E 3T45-30E 3T45-40E Attention: It is important for the safety of persons to follow these instructions. Keep these instructions for future reference. www.3t-components.de WEEE-Reg.-Nr.: DE 77028333...
-
Page 2: Table Of Contents
All contents of these instructions, in particular texts, photographs and graphics, www.3t-components.de are protected by copyright. Unless expressly indicated otherwise, the copyright is held by 3T-Components GmbH & Co. KG. Please ask us if you wish to use the contents of this document. 3T-MOTORS Tubular motors | Table of contents... -
Page 3: Safety Instructions
SAFETY INSTRUCTIONS Please read these important safety instructions before commissioning! Incorrect installation can cause serious personal injury and damage to property. The warranty claim expires in case of non-observance of this user information with all contained notes and regulations. In case of non-observance of these instructions, the manufacturer or supplier shall not be liable for any personal injury or property damage incurred. GENERAL SAFETY INSTRUCTIONS Danger to life from electric shock when working on electrical equipment. -
Page 4: Function Overview
FUNCTION OVERVIEW SCOPE OF DELIVERY – MOTOR TYPE 3T45-E Motor Limit switch adapter Shaft adapter Connection cable 2.5 meters Universal bearing & cotter pin Manual FUNCTION OVERVIEW – MOTOR TYPE 3T45-E APPLICATION Motorized shutters PLUG&PLAY 60 CYCLES SUITABLE FOR 8-sided shafts from 50 mm Simple and fast adjustment of the end positions 0°... -
Page 5: Installation Notes
INSTALLATION NOTES Before installation, all non-essential electrical wiring must be removed, all mechanisms that are not necessary for motorized operation must be deactivated. Do not expose the tubular motor to crushing, impact, falling or contact with any liquids. • Do not punch holes in the entire length of the tube (motor casing) or attach screws to it. Please use suitable suspension springs to fasten the roller shutter curtain to the roller shutter shaft. -
Page 6: Installation Instructions
INSTALLATION INSTRUCTIONS Please note: The motor can be installed on the right-hand side as well as on the left-hand side. • If the direction of rotation is reversed, please exchange the wires for the up and down direction. The setting of the end positions is only possible in the installed state (motor in shutter shaft). •... -
Page 7: Prepare Motor For Installation
INSTALLATION INSTRUCTIONS Prepare motor for installation: When changing the adapter set (SW50 or SW70): Press the safety catch with a screwdriver and pull off the shaft adapter at the same time. > fig. 3.1 / 3.2 • Then replace limit switch adapter and put shaft adapter on adapter holder. >... -
Page 8: Shutter Motor Wiring
INSTALLATION INSTRUCTIONS On the opposite side of the motor, push the roller capsule out of the roller shutter shaft until it fits into the ball bearing inserted in the wall bearing. • Fix roller capsule to roller shutter shaft with self-tapping screw. Position the screw at a punched hole. This prevents the screw from slipping. •... -
Page 9: Setting The End Positions
INSTALLATION INSTRUCTIONS Setting the end positions: 1. Check direction of rotation! When you press the Up button, the roller shutter must move upwards! If this is not the case, exchange the black and brown wires. Please program each motor individually! Automatic mode: Manual mode: Fixed shaft connectors and stoppers... -
Page 10: Troubleshooting
TROUBLESHOOTING WHAT TO DO WHEN ..the engine is not running? Mains voltage is missing. • Check correct connection of the control (switch or timer). • Motor works only when installed in roller shutter shaft. • ... the motor is running in the wrong direction? Swap the two wires for the direction of rotation (brown + black). -
Page 11: Eu Declaration Of Conformity
EU Konformitätserklärung Wir, die Firma 3T Components GmbH & Co. KG Bahnhofstr. 34 55578 Wallertheim Deutschland erklären in alleiniger Verantwortung, dass das weiter unten genannte Produkt Geräteart: Rohrmotor mit elektronischen Endschaltern Modell Artikelnummer 3T45-10E 3T45-10E 3T45-20E 3T45-20E 3T45-30E 3T45-30E 3T45-40E 3T45-40E die grundlegenden Anforderungen der aufgeführten EG/EU-Richtlinien erfüllt: 2014/35/EU... -
Page 12: Email: Info@3T-Components.de
Social Media Links Info, news and tips on roller shutters, awnings, smart home and more: www.facebook.com/3TComponents bit.ly/youtube-3TComponents www.instagram.com/3tcomponents twitter.com/3TComponents 3T-Components GmbH & Co. KG Bahnhofstr. 34 55578 Wallertheim Email: info@3t-components.de Tel: +49 (0) 6732-600 03 69 Fax: +49 (0) 6732-600 54 30 www.3t-components.de...