Grizzly G0938 Owner's Manual
  1. Manuals
  2. Brands
  3. Grizzly Manuals
  4. Saw
  5. G0938
  6. Owner's manual

Grizzly G0938 Owner's Manual

18" scroll saw w/stand
Hide thumbs Also See for G0938:
Table of Contents

Advertisement

Quick Links

Download this manual
MODEL G0938
18" SCROLL SAW w/STAND
OWNER'S MANUAL
(For models manufactured since 02/21)

Advertisement

Table of Contents
loading

Related Manuals for Grizzly G0938

Summary of Contents for Grizzly G0938

  • Page 1 MODEL G0938 18" SCROLL SAW w/STAND OWNER'S MANUAL (For models manufactured since 02/21)
  • Page 2 PROPOSITION 65 WARNING WARNING Drilling, sawing, sanding or machining wood products can expose you to wood dust, a substance known to the State of California to cause cancer. Avoid inhaling wood dust or use a dust mask or other safeguards for personal protection. Go to www.P65Warnings.ca.gov/wood for more information.

  • Page 3: Table Of Contents

    Table of Contents INTRODUCTION ..........................4 Identification..........................4 Glossary.of.Terms........................5 Machine.Data.Sheet........................6 SECTION 1: SAFETY ........................8 Additional.Safety.for.Scroll.Saws....................9 SECTION 2: POWER SUPPLY ...................... 10 SECTION 3: SETUP ........................11 Inventory............................ 11 Needed.for.Setup........................11 Assembly.

  • Page 4: Introduction

    Expanded View Stand Rear Foot pad Front LED work light ON/OFF switch ON/OFF switch Blade guard foot Table insert Mounting hole Worktable Sawdust blower Table top bevel scale Motor Table lock knob Blade storage (under table) Model G0938 (Mfd. Since 02/21)

  • Page 5: Glossary.of.terms

    Trailing edge Variable switch dial allows greater versatility when cutting a variety of materials. Adjust the Workpiece speed between 500 to 1500 strokes per minute (SPM) by turning the control knob clockwise or counter clockwise. Model G0938 (Mfd. Since 02/21)

  • Page 6: Machine.data.sheet

    Main Horsepower ................................1/9 HP Phase ................................Single-Phase Amps ..................................1.6A Speed ..............................1400 - 1500 RPM Type ................................Universal (DC) Power Transfer ................................ Direct Bearings ........................Sealed & Permanently Lubricated Model G0938 (Mfd. Since 02/21) Model G0938 Page 1 of 2...
  • Page 7 Tool-Less Blade Holder Accepts Pin-End & Plain-End Blades Variable Blade Speed Machine Stand Flexible Sawdust Blower & LED Worklight Hold-Down Fork Dust Port 1-1/4" Accessories: Pin-End Blade 5" Hex Wrench 3mm Model G0938 (Mfd. Since 02/21) Model G0938 Page 2 of 2...

  • Page 8: Section 1: Safety

    Everyday eyeglasses have only impact–resistant loss. lenses. They ARE NOT safety glasses. NOTE: Glasses or goggles not in compliance with ANSI Z87.1 could seriously injure you when they break. Model G0938 (Mfd. Since 02/21)

  • Page 9: Additional.safety.for.scroll.saws

    13. HOLD WORKPIECE FIRMLY against the table top. 14. NEVER CUT MATERIAL that is too small to be held safely. Model G0938 (Mfd. Since 02/21)

  • Page 10: Section 2: Power Supply

    Make sure this is connected to a known ground. WARNING This tool is for indoor use only. Do not Two-Pronged Receptacle expose to rain or use in damp locations. Adapter -10- Model G0938 (Mfd. Since 02/21)

  • Page 11: Section 3: Setup

    Rear bracket - lower support Front bracket - upper support Front bracket - lower support Stand hardware bag Cushion Flange nut Carriage bolt Hex bolt Flat washer Sleeve Stand leg (front) Stand leg (rear) -11- Model G0938 (Mfd. Since 02/21)

  • Page 12: Assembly

    5. Tighten all four nuts using two 13 mm or NOTE: To avoid rocking, all bolts must be adjustable wrenches. tightened securely using a 13 mm or adjustable NOTE: Do not over tighten nuts, it may damage wrench. the saw base. -12- Model G0938 (Mfd. Since 02/21)
  • Page 13 Plain-end blade removal (Fig. F, G, H) 1. Remove the table insert (1) by pushing it up from under the worktable. NOTE: Be careful not to make contact with the blade. -13- Model G0938 (Mfd. Since 02/21)
  • Page 14 If the blade is tightened too tight, the lever will be difficult to lower and could result in damage to the blade holder or arm assembly. (Fig. I) -14- Model G0938 (Mfd. Since 02/21)
  • Page 15 (8). (Fig. H) NOTE: Apply slight downward pressure on 5. Replace the table insert, making sure it is not the upper arm when removing blade from above the worktable surface. upper blade holder. -15- Model G0938 (Mfd. Since 02/21)
  • Page 16 To avoid injury from accidental starting, being pulled upward by the saw blade action. always turn the switch OFF and unplug the scroll saw before moving, replacing the blade, or making adjustments. -16- Model G0938 (Mfd. Since 02/21)

  • Page 17: Section 4: Operations

    This saw uses 5 in. (127 mm) long pin-end or plain-end type blades. 12. Blades wear faster when cutting plywood or particle board which is very abrasive. Angle cutting in hardwoods reduces blade tooth set faster due to the blade deflection. -17- Model G0938 (Mfd. Since 02/21)
  • Page 18 (11 - Fig. S) to the rear of the saw. Tilt the table to the right, it will stop at the angle of 15°. 4. Tighten the table lock knob (6). 5. Follow Steps 5–7 under Left Bevel Cutting. -18- Model G0938 (Mfd. Since 02/21)
  • Page 19 (4) prior to touching the leading edge of the workpiece against the blade (3). 8. Slowly feed the workpiece into the blade, guiding the workpiece against the straight edge and press the workpiece down against the table while cutting. -19- Model G0938 (Mfd. Since 02/21)

  • Page 20: Section 5: Maintenance

    ● ANSI S12.6 (S3.19) hearing protection, replacement parts. ● NIOSH/OSHA/MSHA respiratory protection. An occasional coat of paste wax on the work table will allow the wood being cut to glide smoothly across the work surface. -20- Model G0938 (Mfd. Since 02/21)

  • Page 21: Section 6: Service

    1. Loosen blade holder lock screw holding Blade not in line blade holder to arms. Adjust position of with arm motion. blade holders. Retighten blade holder lock screw. See BLADE REMOVAL AND INSTALLATION section. -21- Model G0938 (Mfd. Since 02/21)

  • Page 22: Section 7: Wiring

    Double-check. all. wires. dis- the. power. source.. To. reduce. the. risk. of. being. connected.or.connected.during.any.wiring.task.to. shocked,.wait.at.least.this.long.before.working.on. ensure.tight.connections. capacitors. CIRCUIT REQUIREMENTS.. You. MUST. follow. EXPERIENCING DIFFICULTIES. If.you.are.expe- the.requirements.at.the.beginning.of.this.manual riencing.difficulties.understanding.the.information. when.connecting.your.machine.to.a.power.source.. included. in. this. section,. contact. our. Technical. Support.at.(570).546-9663. -22- Model G0938 (Mfd. Since 02/21)

  • Page 23: Wiring Diagram

    Wiring Diagram 110V 5-15 PLUG WHITE BLACK GREEN TERMINAL BLOCK BLACK WHITE BROWN BLACK WHITE BLUE BLACK WHITE BLACK BLACK ROCKER SWITCH LED CONTROLLER ASSEMBLY BLACK LED LAMP ASSEMBLY READ ELECTRICAL SAFETY -23- Model G0938 (Mfd. Since 02/21) ON PAGE 22!

  • Page 24: Section 8: Parts

    SECTION 8: PARTS We.do.our.best.to.stock.replacement.parts.when.possible,.but.we.cannot.guarantee.that.all.parts.shown. are.available.for.purchase..Call.(800) 523-4777.or.visit.www.grizzly.com/parts.to.check.for.availability. Main 100-1 BUY PARTS ONLINE AT GRIZZLY.COM! -24- Model G0938 (Mfd. Since 02/21) Scan QR code to visit our Parts Store.
  • Page 25 TORSION SPRING 1.4 X 33 X 28 P0938057 ROCKER SWITCH 10A 115 P0938115 LEFT COVER P0938058 FLAT HD TAP SCREW M5 X 16 116 P0938116 RIGHT COVER BUY PARTS ONLINE AT GRIZZLY.COM! -25- Model G0938 (Mfd. Since 02/21) Scan QR code to visit our Parts Store.

  • Page 26: Stand

    P0938124 FRONT FOOT P0938132 REAR FOOT P0938125 UPPER SUPPORT BRACKET (SIDE) P0938133 UPPER SUPPORT BRACKET (FRONT) P0938126 LOWER SUPPORT BRACKET (FRONT) BUY PARTS ONLINE AT GRIZZLY.COM! -26- Model G0938 (Mfd. Since 02/21) Scan QR code to visit our Parts Store.

  • Page 27: Labels.&.Cosmetics

    Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes off or becomes unreadable, the owner of this machine MUST replace it in the original location before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com. BUY PARTS ONLINE AT GRIZZLY.COM! -27- Model G0938 (Mfd.

Table of Contents