Memory Mode; Errors And Troubleshooting - Braun ThermoScan IRT 6020 Manual

Memory mode

IRT 6520
1. This model stores the last 9 temperature measurements. To display the stored measurement,
the thermometer must be turned on.
2. Press the Mem button.
The display shows the temperature, and when releasing the Mem button, the stored
temperature for that memory number is displayed, together with "M".
3. Each time the Mem button is pushed, the stored reading and an M is
displayed to indicate each temperature measurement (eg. M2).
Memory mode is automatically exited by not pressing the memory
button for 5 seconds.
IRT 6020
1. The last temperature taken is stored in its memory and will be
automatically displayed for 5 seconds when it is turned on again.
Night light feature
IRT 6520 Only
The thermometer includes a convenient night light to illuminate the display in a dim
environment.
The light will turn on when you press any button. It will stay on until the thermometer is inactive
for up to 15 seconds even after temperature is taken.
Changing the temperature scale
Your Braun ThermoScan is shipped with the Celsius (°C) temperature scale activated. If you wish to switch to Fahrenheit
(°F) and/or back from Fahrenheit to Celsius, proceed as follows:
1. Make sure the thermometer is turned off.
2. Press and hold down the Power button . After about 3 seconds the display will show this
sequence: °C / SET / °F / SET.
3. Release the Power button when the desired temperature scale is shown. There will be a
short beep to confirm the new setting, then the thermometer is turned off automatically.
6
Care and cleaning
The probe tip is the most delicate part of the thermometer. It must be clean and intact to ensure accurate
readings. If the thermometer is ever accidentally used without a Hygiene cap, clean the probe tip as follows:
Very gently wipe the surface with a cotton swab or soft cloth moistened with alcohol. After the
alcohol has completely dried out, you can put a new Hygiene cap on and take a temperature
measurement.
If the probe tip is damaged, please contact Consumer Relations.
Use a soft, dry cloth to clean the thermometer display and exterior. Do not use abrasive cleaners.
Never submerge this thermometer in water or any other liquid. Store thermometer and Hygiene
caps in a dry location free from dust and contamination and away from direct sunlight.
Additional Hygiene caps (LF 40) are available at most stores carrying Braun ThermoScan.
Replacing the batteries
The thermometer is supplied with two 1.5 V type AA (LR 06) batteries.
1. Insert new batteries when the battery symbol appears on the display.
2. Open the battery compartment. Remove the batteries and replace with new batteries, making
sure the poles are in the right direction.
3. Snap battery door into place.

Errors and troubleshooting

Error Message Situation
No Hygiene cap is attached.
The thermometer probe was not positioned
securely in the ear.
An accurate measurement
was not possible.
POS = position error
Ambient temperature is not within
the allowed operating range
(10 – 40 °C or 50 – 104 °F).
Temperature taken is not within
typical human temperature range
(34 – 42.2 °C or 93.2 – 108 °F).
HI = too high
LO = too low
System error – self-check display flashes
continuously and will not be followed by
the ready beep and the ready symbol.
If error persists,
If error still persists,
English
Solution
Attach new, clean Hygiene cap.
Take care that the positioning of the probe is correct
and remains stable.
Replace Hygiene cap and reposition.
Press Start button to begin a new measurement.
Allow the thermometer to remain for
30 minutes in a room where
the temperature is between 10 and 40 °C
or 50 and 104 °F .
Make sure the probe tip and lens are clean and a
new, clean Hygiene cap is attached. Make sure the
thermometer is properly inserted. Then, take a new
temperature.
Wait 1 minute until the thermometer turns off
automatically, then turn on again.
... reset the thermometer by removing the batteries
and putting them back in.
... please contact the Service Centre.
7