Download
Share
Print this page
  1. Manuals
  2. Brands
  3. XDP Recreation Manuals
  4. Play Sets & Playground Equipment
  5. 86900
  6. Manual

XDP Recreation 86900 Manual

Swing, climb & glide play center
Hide thumbs

Advertisement

Quick Links

Download this manual
Allow 6 - 12 ft of clearance around the perimeter of the swing set area when fully assembled.
OWNER'S MANUAL, ASSEMBLY INSTRUCTIONS, CARE, MAINTENANCE AND USER'S GUIDE
Please read this entire instruction and assembly manual completely before proceeding. You must follow all
safety instructions while using this equipment. The surface area where this swing set is set up must be level and free of
all debris. This set is designed to be anchored into the ground and is not to be set up on any hard surfaces such as
concrete, hardened soil or asphalt. Proper surfacing under and surrounding the set adds to the safety level such as
sand or mulch. Read all cautionary statements on the following pages before using this equipment and save this
instruction manual. DO NOT ALLOW CHILDREN TO PLAY ON THIS GYM SET UNSUPERVISED! CONSTANT
ADULT SUPERVISION IS REQUIRED. Do not use when raining or during any inclement weather (i.e. rain, sleet, snow,
ice, high winds, thunderstorms or lightening). DO NOT ALLOW CHILDREN TO JUMP ON OR CLIMB UP ON THIS
SET'S TOP BAR.
For warranty details and registration see the back page of this manual.
FOLLOW ALL ASSEMBLY INSTRUCTIONS AS WRITTEN IN THIS MANUAL
Please retain sales receipt for warranty purposes. DO NOT RETURN THE SET TO
THE STORE
. If replacement parts or customer service is needed please contact XDP Recreation by email at
service@xdprecreation.com or by calling 1-866-884-0535 between 8:00am and 5:00pm (Eastern Standard Time), Monday - Friday. This
gym is designed to be used safely by up to seven (7) children, ages 3 years to 8 years, with weight capacity of 100 lbs per child or total
combined weight limit of 700 lbs for all seven (7) children. This play gym is designed for backyard use only and is NOT intended for
playgrounds, schools, day care facilities, nurseries or other public places. Follow all assembly instructions carefully and as directed in
this manual. This gym conforms to all safety requirements by ASTM for Home Playground equipment when properly assembled using the
instructions enclosed. Adult assembly is required. Contains small parts. For proper stability and safety this gym set should be installed
with ground anchors.
Anchor Kits can be ordered directly from XDP RECREATION at https://www.xdprecreation.com or by calling
Model 86900
SWING, CLIMB & GLIDE PLAY CENTER
Assembled dimensions are 176"*69"*73".
Important Instructions & Warnings!
1.866.884.0535 or thru your retailer of choice.
.

Advertisement

loading

Related Manuals for XDP Recreation 86900

Summary of Contents for XDP Recreation 86900

  • Page 1 Please retain sales receipt for warranty purposes. DO NOT RETURN THE SET TO THE STORE . If replacement parts or customer service is needed please contact XDP Recreation by email at service@xdprecreation.com or by calling 1-866-884-0535 between 8:00am and 5:00pm (Eastern Standard Time), Monday - Friday. This gym is designed to be used safely by up to seven (7) children, ages 3 years to 8 years, with weight capacity of 100 lbs per child or total combined weight limit of 700 lbs for all seven (7) children.

  • Page 2: Important Instructions And Warnings

    IMPORTANT INSTRUCTIONS AND WARNINGS WARNING READ ALL INSTRUCTIONS BEFORE ASSEMBLING OR USING THIS EQUIPMENT. AGE & WEIGHT LIMIT  This product is designed to be used by up to seven (7) children between the ages of 3 to 8. Maximum user weight is 100 pounds (45 kg) each with a combined maximum weight of 700 pounds (318 kg).

  • Page 3: Weather Conditions

     DO NOT install your play set over hard surface, e.g. asphalt, concrete, packed earth, tile or brick floor. A fall onto a hard surface can result in serious injury or death to the user. The following is a list of recommended ground covers from the Consumer Product Safety Commission: SUGGESTED MATERIAL UNCOMPRESSED DEPTH...
  • Page 4 PLAY SUPERVISION  DO NOT allow more than one child to play on the individual swing or slide component at any one time.  DO NOT allow children to stand on the slide, swing seats, trapeze, seesaw, rocky rider, disc swing or glide ride.

  • Page 5: Care And Maintenance Instructions

    INSPECTION PRIOR TO EACH USE OR DAILY INSPECTION  DO NOT use the equipment if any bolts or nuts are missing or loose. ALWAYS check to ensure the equipment and all parts are well secured and stable before each use. ...
  • Page 6 DO NOT RETURN TO RETAILER WHERE YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdprecreation.com...
  • Page 7 ANCHORING (NOTE:ANCHORS ARE NOT INCLUDED-MUST BE PURCHASED SEPARATELY) There are different ways of anchoring the equipment, depending on the type of ground on which the equipment is to be installed. Make sure that all anchors are below ground level to prevent tripping.
  • Page 8 FRAME LEG 12-5/8” CONCRETE 5” 2” BRICK OR GRAVEL BED Note: The maximum fall height for this product is 4 feet. The minimum ground clearance between the bottom of the suspended plays and the playing or ground surface must be 8 inches. You must maintain a minimum of 8 inches of ground clearance.

  • Page 9: Care And Maintenance Checklist

    CARE AND MAINTENANCE CHECKLIST AT THE BEGINNING OF EACH PLAY SEASON:  Tighten all hardware.  Lubricate all metallic moving parts.  Check all protective coverings on bolts, pipes, edges, and corners. Replace if they are loose, cracked, or missing. ...

  • Page 10: Tools Needed

    TOOLS NEEDED Please prepare the following tools prior to assembling this equipment. Special Socket Wrench Tape Measure (Included) (Not included) Hammer Wrench (If you intend to install anchor, this is needed) (Included) Wrench Medium Allen Wrench (Not Included) (Included) Flat Head and Philips Head Screwdriver Big Allen Wrench (Not included) (Included)
  • Page 11 Part list for main frame assembly RIGHT TOP BAR MIDDLE TOP BAR 1 MIDDLE TOP BAR 2 LEFT TOP BAR TOP SECTION LEG BOTTOM SECTION LEG WITH FOAM CROSS BAR (WITH TWO HOLES) Hardware used for main frame assembly BOLT 5/16" (63MM) BOLT 5/16"...
  • Page 12 Part list for glide ride assembly L1-N TOP SECTION HANGER L2-N BOTTOM SECTION HANGER L3-N GLIDE SEAT SUPPORT TUBE CAP (PRE-ASSEMBLED ON L1-N) SMALL NYLON BEARING (PRE-ASSEMBLED ON L1-N) LARGE NYLON BEARING (PRE-ASSEMBLED ON L2-N) GLIDE SEAT FOOTREST Hardware used for glide ride assembly BOLT 1/4”...
  • Page 13 Part list for belt swing seat assembly SWING ROPE ATTACHMENT BOLT (PRE-ASSEMBLED ON J1) S-HOOK WITH LEVER (PRE-ASSEMBLED ON J1) CARABINER (PRE-ASSEMBLED ON J1) BELT SWING SEAT (PRE-ASSEMBLED ON J1) Hardware used for belt swing seat assembly NUT 5/16’’ PLASTIC CAP (WITH ARC WASHER) Part list for SUPER DISC Swing assembly DISC SWING ROPE...
  • Page 14 Part list for climbing ladder assembly 3 RUNG CLIMBING TUBE WITH ONE COMPRESSED END 3 RUNG CLIMBING TUBE CONNECTING TUBE FOR CLIMBING LADDER (TWO HOLE IN THE MIDDLE) 2 RUNG TOP SECTION TUBE 1 RUNG TOP SECTION TUBE 2 RUNG BOTTOM SECTION TUBE 1 RUNG BOTTOM SECTION TUBE Part list for climbing net assembly CONNECTING TUBE FOR...
  • Page 15 ASSEMBLY INSTRUCTIONS  Place the playground equipment on level ground and not less than 6ft (1.8m) from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry line or electrical wires.  Do not install the playground equipment over concrete, asphalt, packed earth or any other hard surface;...
  • Page 16 STEP 1 – Assemble the top bar frame of the swing set  Connect A1, A2, A3 and A4 and secure with B1, B5, B4 and B3 as shown below. Note: All round holes on the TOP BAR should be facing up and concave holes facing down.
  • Page 17 STEP 2 – Assemble the support legs of swing set  Connect A1 to A5 and secure using B1, B5, B4 and B3 as shown below.  Repeat this step for the other side of the swing set (A4).  Connect A1 and A4 to A5 and A6. NOTE: Do not over-tighten the nuts and bolts at every step.
  • Page 18 STEP 3 – Attach the crossbar to the support legs  Attach A7 to the outer side of A5 & A6 and secure using B2, B6, B4 and B3.  Repeat this step for the other side of the swing set (A4). NOTE: Do not over-tighten the nuts and bolts at every step.
  • Page 19 STEP 4 - Assemble the support legs and crossbars of climbing ladder and climbing net  Connect A17 to A13 and then connect to top bar A3.  Connect A16 to A14 and then connect to top bar A2.  Connect A15 to A12 and then connect to top bar A2 and A3. DO NOT RETURN TO RETAILER WHERE YOU PURCHASED AT.
  • Page 20  Attach A7 to the outer side of A13 & A12 and secure using B2, B6, B4 and B3.  Attach A7 to the outer side of A14 & A12 and secure using B2, B6, B4 and B3. DO NOT RETURN TO RETAILER WHERE YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdprecreation.com...
  • Page 21 STEP 5 - Climbing ladder assembly IMPORTANT: ADULT ASSEMBLY is REQUIRED/NEEDED  Attach A11 to the outer side of A13 & A14 and secure using C5, C8, C9 and C7.  Attach A11 to the outer side of A17 & A16 and secure using C5, C8, C9 and C7. NOTE: ONLY 1 child on Climbing Net or Climbing Ladder at a time.
  • Page 22 STEP 6 - Climbing ladder assembly (continued) IMPORTANT: ADULT ASSEMBLY is REQUIRED/NEEDED.  Attach A8 to A9 and secure using C10, C8, C9 and C7.  Attach A8 to the outer side of A11 (Top) and secure using C6, C8, C9 and C7. ...
  • Page 23 STEP 7 - Climbing net assembly IMPORTANT: ADULT ASSEMBLY is REQUIRED/NEEDED.  Insert C12 (short one) into the holes on A10 as shown in Diagram A and Diagram C. Insert C11 (long one) into the holes on A12 and A15 as shown in Diagram B. Please follow the arrow to insert C11 and C12 into the holes.
  • Page 24 STEP 8 - Climbing net assembly (continued) IMPORTANT: ADULT ASSEMBLY is REQUIRED/NEEDED. The climbing net should look like below diagram after completion of this STEP 8. Important! It is critical to note the Vertical Hole and Horizontal Hole of C3 when you assemble the following steps.
  • Page 25 Now, you are ready to assemble.  Thread one end of the rope C1 through the bottom hole on the A10 of the BOTTOM part of the set. Thread the rope C1 into Vertical hole of the C3. Total of 5 pcs of C3 is needed for now.
  • Page 26  Thread the other end of rope C1 through the bottom hole on the A10 of the TOP part of the set.  Thread the rope C1 into the Vertical Hole of one C3 and out through the Horizontal hole as TIGHT as possible to create tension. Then and secure C1 and this C3 ONLY with C4 at this moment.
  • Page 27 STEP 9 - Climbing net assembly (continued) IMPORTANT: ADULT ASSEMBLY is REQUIRED/NEEDED. The climbing net should look like below diagram after completion of this STEP 9. STEP 9 STEP 8  Thread one end of the rope C1-1 through the top LEFT hole on the A12. Then bring up the first C3 in this Left Vertical rope C1 and thread the rope through the Horizontal Hole of the C3 and the first C3 of the Right Vertical rope C1 and come out through the top RIGHT hole on the Right A12.
  • Page 28  Now, go back to secure C3 with the starting end of the rope C1-1 with C4. Remember to thread the rope C1-1 into the Vertical Hole of the C3 and out through the Horizontal hole before securing C1-1 and C3 with C4. See Diagram B for illustration.
  • Page 29  Now, thread one end of the rope C1-2 through hole 10 from right to left. Then thread through C3 and A15 until hole 17.  Now, pull the rope as TIGHT as possible from both ends and secure the rope with C3 and C4 as illustrated in Diagram C.

  • Page 30: Step 10 - Glide Ride Assembly

    STEP 10 - Glide ride assembly  Attach L4 and L3 to A4 using N3R, L5 and N7 as shown. Use special socket wrench and screw driver to tighten N3R and N7. STEP 11 – Glide ride assembly (continued)  Insert L2-N (straight end) into L1-N and secure with N13-1, N14, N6 and N15 on both sides as shown below.
  • Page 31 STEP 12 – Glide ride assembly (continued)  Insert L2-N (straight end) into M5 and secure with N4 and N12 on both sides.  Attach M1 to the top of L1-N (curved end). Align holes and insert M2. (Please check if M1 and M2 are pre-assembled properly.) ...
  • Page 32 STEP 13 – Glide ride assembly (continued)  Attach L3-N to L2-N on both sides and secure with N5, M3, N11 and N8. (Please check if M3 are pre-assembled properly.) Concave holes face up L1-N L2-N Round holes face down L3-N DO NOT RETURN TO RETAILER WHERE YOU PURCHASED AT.
  • Page 33 STEP 14 – Glide ride assembly (continued)  Attach M4 to L3-N and secure with N1, N6 and N9. L1-N L2-N L3-N L3-N The swing set should look like this now. DO NOT RETURN TO RETAILER WHERE YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdprecreation.com...
  • Page 34 STEP 15 - Belt swing seat assembly (w. "Adjustable Height" Feature)  Insert J2 through A3 and A4 and secure with J8 and J6 as shown in Diagram A.  If you wish to shorten the rope length, follow Diagram B. Please make sure the lever on J3 is lift up before adjusting and put down after adjusting.
  • Page 35 STEP 16 – Super Disc swing assembly  Separation of foam tube R3-1 from R3-N  Insert the foam tube R3-1 into R4-N first, then insert R3-N into R3-1 in R4-N.  Slide the smaller ends of R3-N tubes into the pockets of Super Disc swing fabric (R4-N).
  • Page 36 STEP 17 – Attach Super Disc swing to the swing set frame  Assemble R1 to the Super Disc swing by inserting R2 and securing with F2-N and F1-N as shown in Diagram A.  Connect Super Disc swing to the top bar by inserting R2-1through A1 and A2, securing with F3-N and F1-N as shown in Diagram B.
  • Page 37 Congratulations! You have now completed the swing set assembly. Please make sure to thoroughly check all parts and hardware to make sure all bolts and nuts are well secured before using the playground equipment. WARNING - Do not let children use the playground equipment until it is properly assembled and anchored.

  • Page 38: Customer Support

    What does this warranty NOT cover? This limited warranty does not cover XDP Recreation products which: fail due to (1) normal wear; (2) abuse and misuse; (3) improper maintenance; (4) unauthorized repairs or incorrect parts use; or (5) are used for commercial or other income producing purposes.
  • Page 39 IF NEEDED, GROUND ANCHORS CAN BE BOUGHT FROM THE STORE YOU PURCHASED THIS SET AT OR BY PURCHASING FROM XDP RECREATION'S WEBSITE AT www.xdprecreation.com XDP RECREATION LLC, 5910 SHILOH ROAD EAST, SUITE 108, ALPHARETTA, GEORGIA 30005 REGISTER YOUR “XDP” PURCHASED / PRODUCT PLEASE VISIT OUR WEBSITE at www.xdprecreation.com to register your...
  • Page 40 Dear Customer, THANK YOU for being an XDP Recreation Customer. IT’S HERE – The NEW FIREFLY LED SWING Check out our Website or the General Marketplace For this FANTASTICALLY / FUN STROBING – LED – COLORED – FLASHING MODES SWING www.xdprecreation.com...