Advertisement
Quick Links
Allow 6 - 12 ft of clearance around the perimeter of the swing set area when fully assembled.
OWNER'S MANUAL, ASSEMBLY INSTRUCTIONS, CARE, MAINTENANCE AND USER'S GUIDE
Please read this entire instruction and assembly manual completely before proceeding. You must follow all safety instructions
while using this equipment. The surface area where this swing set is set up must be level and free of all debris. This set is
designed to be anchored into the ground and is not to be set up on any hard surfaces such as concrete, hardened soil or asphalt.
Proper surfacing under and surrounding the set adds to the safety level such as sand or mulch. Read all cautionary statements on
the following pages before using this equipment and save this instruction manual.
THIS GYM SET UNSUPERVISED! CONSTANT ADULT SUPERVISION IS REQUIRED. Do not use when raining or during any
inclement weather (i.e. rain, sleet, snow, ice, high winds, thunderstorms or lightening).
ON OR CLIMB UP ON THIS SET'S TOP BAR.
For warranty details and registration see the back page of this manual.
FOLLOW ALL ASSEMBLY INSTRUCTIONS AS WRITTEN IN THIS MANUAL
Please retain sales receipt for warranty purposes. DO NOT RETURN THE SET TO
THE STORE
. If replacement parts or customer service is needed please contact XDP Recreation by email at
service@xdprecreation.com or by calling 1-866-884-0535 between 8:00am and 5:00pm (Eastern Standard Time), Monday - Friday. This
gym is designed to be used safely by up to seven (7) children, ages 3 years to 8 years, with weight capacity of 100 lbs per child or total
combined weight limit of 700 lbs for all seven (7) children (318kg). This play gym is designed for backyard use only and is NOT intended
for playgrounds, schools, day care facilities, nurseries or other public places. Follow all assembly instructions carefully and as directed in
this manual. This gym conforms to all safety requirements by ASTM for Home Playground equipment when properly assembled using the
instructions enclosed. Adult assembly is required. Contains small parts. For proper stability and safety this gym set should be installed
with ground anchors.
Anchor Kits can be ordered directly from XDP RECREATION at https://www.xdprecreation.com or by calling
MODEL 74510G
Free N Swing Set
Assembled dimensions are 168"*93"*73".
Important Instructions & Warnings!
1.866.884.0535 or thru your retailer of choice.
DO NOT ALLOW CHILDREN TO PLAY ON
DO NOT ALLOW CHILDREN TO JUMP
Advertisement
Related Manuals for XDP Recreation 74510G
Summary of Contents for XDP Recreation 74510G
- Page 1 Please retain sales receipt for warranty purposes. DO NOT RETURN THE SET TO THE STORE . If replacement parts or customer service is needed please contact XDP Recreation by email at service@xdprecreation.com or by calling 1-866-884-0535 between 8:00am and 5:00pm (Eastern Standard Time), Monday - Friday. This gym is designed to be used safely by up to seven (7) children, ages 3 years to 8 years, with weight capacity of 100 lbs per child or total combined weight limit of 700 lbs for all seven (7) children (318kg).
-
Page 2: Important Instructions And Warnings
Anchor kit. If you anticipate severe winds, the product should be moved to a sheltered location or completely disassembled. Anchor kits can be ordered directly from XDP RECREATION at https//:www.xdprecreation.com or by calling 1-866-884-0535. - Page 3 DO NOT install your play set over hard surface, e.g. asphalt, concrete, packed earth, tile or brick floor. A fall onto a hard surface can result in serious injury or death to the user. The following is a list of recommended ground covers from the Consumer Product Safety Commission: SUGGESTED MATERIAL UNCOMPRESSED DEPTH...
- Page 4 PLAY SUPERVISION DO NOT allow more than one child to play on the individual swing or slide component at any one time. DO NOT allow children to stand on the slide, swing seats, trapeze, seesaw, rocky rider, disc swing or glide ride.
-
Page 5: Care And Maintenance Instructions
INSPECTION PRIOR TO EACH USE OR DAILY INSPECTION DO NOT use the equipment if any bolts or nuts are missing or loose. ALWAYS check to ensure the equipment and all parts are well secured and stable before each use. ... - Page 6 ANCHORING (NOTE:ANCHORS ARE NOT INCLUDED-MUST BE PURCHASED SEPARATELY) There are different ways of anchoring the equipment, depending on the type of ground on which the equipment is to be installed. Make sure that all anchors are below ground level to prevent tripping.
- Page 7 FRAME LEG CONCRETE 12-5/8” 5” 2” BRICK OR GRAVEL BED Note: The maximum fall height for this product is 4 feet. The minimum ground clearance between the bottom of the suspended plays and the playing or ground surface must be 8 inches. You must maintain a minimum of 8 inches of ground clearance.
- Page 8 CARE AND MAINTENANCE CHECKLIST AT THE BEGINNING OF EACH PLAY SEASON: Tighten all hardware. Lubricate all metallic moving parts. Check all protective coverings on bolts, pipes, edges, and corners. Replace if they are loose, cracked, or missing. ...
-
Page 9: Tools Needed
TOOLS NEEDED Please prepare the following tools prior to assembling this equipment. Special Socket Wrench Tape Measure (Not included) (Not included) Hammer Wrench (If you intend to install anchor, this is needed) (Included) Wrench Medium Allen Wrench (Not Included) (Included) Flat Head and Philips Head Screwdriver Big Allen Wrench (Not included) - Page 10 Part list for main frame assembly LEFT TOP BAR MIDDLE TOP BAR RIGHT TOP BAR TOP SECTION LEG BOTTOM SECTION LEG WITH FOAM BOTTOM SECTION LEG WITH FOAM CROSS BAR (WITH TWO HOLES) CROSS BAR (WITH FOUR HOLES) Hardware used for main frame assembly BOLT 5/16"...
- Page 11 Part list for swing seat assembly PVC COVERED CHAIN EYE BOLT WITH ATTACHMENT BOLT (PRE-ASSEMBLED ON J1) ONE EYE BOLT WITH ATTACHMENT J3-N BOLT(PRE-ASSEMBLED ON J1) ***The plastic is Ivory Color*** SWING SEAT Hardware used for swing seat assembly NUT 5/16" WASHER 5/16"...
- Page 12 Part list for SUPER DISC Swing assembly R1-N PVC COVERED CHAIN TWO EYE BOLTS WITH R2A-N ATTACHMENT BOLT (PRE-ASSEMBLED ON R1-N) ONE EYE BOLT WITH ATTACHMENT R2B-N BOLT (PRE-ASSEMBLED ON R1-N) R3-N DISC SWING TUBE DISC SWING TUBE FOAM R3-1 (PRE-ASSEMBLED ON R3-N) R4-N DISC SWING FABRIC...
- Page 13 PLASTIC CONNECTOR BOLT 1/4" (38MM) BOLT 1/4" (115MM) SPRING WASHER CAP NUT 1/4" CAP BOLT 1/4"x1/2" SPRING WASHER (SMALL) BOLT 1/4" (75MM) BOLT 1/4" (58MM) Part list for seesaw assembly SEAT SEAT SUPPORT HANDLE BAR U19-1 LEFT HANDLE BAR SUPPORT U19-2 RIGHT HANDLE BAR SUPPORT L-SHAPED TUBE...
- Page 14 BOLT 5/16” (82MM) BOLT 5/16” (63MM) BOLT 5/16” (68MM) ARC WASHER Φ8.5*T1.5MM NUT 5/16” CAP NUT 1/4” BOLT 1/4” (37MM) SPRING WASHER SCREW M4 (12MM) PLASTIC CAP (WITH FLAT WASHER) FLAT WASHER PLASTIC CAP (WITH ARC WASHER) SPRING WASHER(SMALL) DO NOT RETURN TO RETAILER WHERE YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdprecreation.com...
- Page 15 ASSEMBLY INSTRUCTIONS Place the playground equipment on level ground and not less than 6ft (1.8m) from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry line or electrical wires. Do not install the playground equipment over concrete, asphalt, packed earth or any other hard surface;...
- Page 16 Note: All round holes should be facing up and concave holes facing down. NOTE: Do not over-tighten the nuts and bolts at every step. 2. Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts.
- Page 17 Repeat this step for the right side of the swing (A3 and A7) NOTE: Do not over-tighten the nuts and bolts at every step. 2. Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts.
- Page 18 Repeat this step for the right side of the swing set (A3 with A7). NOTE: Do not over-tighten the nuts and bolts at every step. 2. Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts.
- Page 19 Attach A10 to the outer side of A8 & A9 and secure using B2, B6, B4 and B3. NOTE: Do not over-tighten the nuts and bolts at every step. 2. Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts.
- Page 20 DO NOT RETURN TO RETAILER WHERE YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdprecreation.com...
- Page 21 STEP 5 –"SWING SEAT" assembly (w. "Adjustable Height" Feature) Important: Please make sure to use the J1 with J3-N (the plastic is Ivory Color). This is CRITICAL to other assembly steps. Connect swing seat to the chains by inserting J3 through K1 and secure with J7, J9 and J6 as shown in Diagram A.
- Page 22 Diagram B J3-N J3-N If you wish to shorten the chain length, follow the below diagram. Diagram C NOTE: Do not over-tighten the nuts and bolts at every step. 2. Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts.
- Page 23 STEP 6 - "Stand R Swing " seat assembly (w. "Adjustable Height" Feature) Important: Please make sure to use the J1A with J3A-N (the plastic is Green Color). This is CRITICAL to other assembly steps. Connect Stand R Swing to the chains by inserting J3A through K2 and secure with J7A, J9A and J6A as shown in Diagram A.
- Page 24 Diagram B J3A-N J3A-N If you wish to shorten the chain length, follow the below diagram. Diagram C NOTE: Do not over-tighten the nuts and bolts at every step. 2. Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts.
- Page 25 STEP7 – Super Disc swing assembly Separation of foam tube R3-1 from R3-N Insert the foam tube R3-1 into R4-N first, then insert R3-N into R3-1 in R4-N. Slide the smaller ends of R3-N tubes into the pockets of Super Disc swing fabric (R4-N).
- Page 26 STEP 8–Attach Super Disc swing to the swing set frame Connect the chain (R1-N) to the Super Disc swing by inserting R2B-N and securing with F2-N and F1-N as shown in Diagram A. Connect Super Disc swing to the top bar by inserting R2A-N through A1 and A2, securing with F3-N and F1-N as shown in Diagram B.
- Page 27 STEP 9 - Slide assembly Insert X5-N into the base of Y2. Secure using Z8, Z6 and Z4. Attach X4-N to Y2. Note: Make sure that the bolt holes face up. X4-N Bolt hole faces up. X5-N NOTE: 1.
- Page 28 STEP 10 - Slide assembly (continued) Attach X6 to X1-N and X2-N. The inner sides of both X2-N and X1-N, where X6 (slide ladder steps) is attached to, are with concave holes. Secure each side using Z1, Z6 and Z4. ...
- Page 29 STEP 11- Slide assembly (continued) Secure the two sides of the slide using Z2, Z6 and Z4, in the sequence shown in the diagram. Attach X4-N to X1-N and X2-N and secure using Z1, Z6, Z3 and Z5 as shown in the enlarged diagram.
- Page 30 STEP 12 - Slide assembly (continued) Fit Y1 in between X1-N and A11and secure using Y1, Z7, Z6, Z3 and Z5. X1-N NOTE: 1. Do not over-tighten the nuts and bolts at every step. 2. Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts.
- Page 31 STEP 13 - Seesaw assembly Attach U20 to A9. Align the holes on U20 to the two holes on the bottom of A9 and secure using U3, U4, U15 and U5 as shown below. NOTE: 1. Do not over-tighten the nuts and bolts at every step. 2.
- Page 32 STEP 14 - Seesaw assembly (continued) Secure U17 to U20 by using U2, U14, U10 and U5 as shown below. NOTE: 1. Do not over-tighten the nuts and bolts at every step. 2. Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts.
- Page 33 STEP 15 - Seesaw assembly (continued) Attach U18 to U19-1 and U19-2 and secure using U9 and U21. Repeat for other U18, U19-1 and U19-2. U19-1 U19-2 DO NOT RETURN TO RETAILER WHERE YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdprecreation.com...
- Page 34 STEP 16 - Seesaw assembly (continued) Secure U19-1 & U19-2 to U17 using U1, U4 and U5 as shown below. Repeat for the other side. U19-2 U19-1 NOTE: 1. Do not over-tighten the nuts and bolts at every step. 2.
- Page 35 STEP 17 - Seesaw assembly (continued) Secure U16 to U19-1 and U19-2 using U7, U8 and U6 as shown below. Repeat for the other side. DO NOT RETURN TO RETAILER WHERE YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdprecreation.com...
- Page 36 Congratulations! You have now completed the swing set assembly. Please make sure to thoroughly check all parts and hardware to make sure all bolts and nuts are well secured before using the playground equipment. WARNING - Do not let children use the playground equipment until it is properly assembled and anchored.
- Page 37 What does this Limited Warranty cover? This warranty covers your XDP Recreation product for one hundred and eight (180) days against defects in material, workmanship, and rust on painted parts which compromise the structural integrity of the product when used for the purpose intended, normal outdoor conditions, and provided it is assembled correctly as illustrated in this manual and receives the proper care and maintenance.
- Page 38 IF NEEDED, GROUND ANCHORS CAN BE BOUGHT FROM THE STORE YOU PURCHASED THIS SET AT OR BY PURCHASING FROM XDP RECREATION'S WEBSITE AT www.xdprecreation.com XDP RECREATION LLC, 5910 SHILOH ROAD EAST, SUITE 108, ALPHARETTA, GEORGIA 30005 REGISTER YOUR “XDP” PURCHASED / PRODUCT PLEASE VISIT OUR WEBSITE at www.xdprecreation.com to register your...
- Page 39 Dear Customer, 2020 THANK YOU for being an XDP Recreation Customer. IT’S HERE – The NEW FIREFLY LED SWING Check out our Website or the General Marketplace For this FANTASTICALLY / FUN STROBING – LED – COLORED – FLASHING MODES SWING www.xdprecreation.com...