1. Manuals
  2. Brands
  3. XDP Recreation Manuals
  4. Play Sets & Playground Equipment
  5. 74520SFW-T
  6. Owner's manual

XDP Recreation 74520SFW-T Owner's Manual

Playground park with water slide
Hide thumbs

Advertisement

Table of Contents

Assembled dimensions are 206" x 91" x 74". (Not Include "Ground Tarp Slide").
Allow 6 - 12 ft of clearance around the perimeter of the swing set area when fully assembled.
OWNER'S MANUAL, ASSEMBLY INSTRUCTIONS, CARE, MAINTENANCE AND USER'S GUIDE
Please read this entire instruction and assembly manual completely before proceeding. You must follow all
safety instructions while using this equipment. The surface area where this swing set is set up must be level and free
of all debris. This set is designed to be anchored into the ground and is not to be set up on any hard surfaces such as
concrete, hardened soil or asphalt.
sand or mulch. Read all cautionary statements on the following pages before using this equipment and save this
DO NOT ALLOW CHILDREN TO PLAY ON THIS GYM SET UNSUPERVISED!
instruction manual.
ADULT SUPERVISION IS REQUIRED.
snow, ice, high winds, thunderstorms or lightening). DO NOT ALLOW CHILDREN TO JUMP ON OR CLIMB UP ON
THIS SET'S TOP BAR.
For warranty details and registration see the back page of this manual.
FOLLOW ALL ASSEMBLY INSTRUCTIONS AS WRITTEN IN THIS MANUAL
Please retain sales receipt for warranty purposes.
THE STORE.
If replacement parts or customer service is needed please contact XDP Recreation by email at
service@xdprecreation.com or by calling 1-866-884-0535 between 8:00am and 5:00pm (Eastern Standard Time), Monday - Friday.
gym is designed to be used safely by up to eight (8) children, ages 3 years to 8 years, with weight capacity of 100 lbs per child or total
combined weight limit of 800 lbs for all eight (8) children (363.6kgs).
intended for playgrounds, schools, day care facilities, nurseries or other public places.
directed in this manual.
assembled using the instructions enclosed.
set should be installed with ground anchors.
Anchor Kits can be ordered directly from XDP RECREATION at https://www.xdprecreation.com or by calling
MODEL 74520SFW-T
Playground Park with Water Slide
Important Instructions & Warnings!
Proper surfacing under and surrounding the set adds to the safety level such as
Do not use when raining or during any inclement weather (i.e. rain, sleet,
This gym conforms to all safety requirements by ASTM for Home Playground equipment when properly
Adult assembly is required.
1.866.884.0535 or thru your retailer of choice.
DO NOT RETURN THE SET TO
This play gym is designed for backyard use only and is NOT
Follow all assembly instructions carefully and as
Contains small parts. For proper stability and safety this gym
CONSTANT
This
0

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 74520SFW-T and is the answer not in the manual?

Questions and answers

Related Manuals for XDP Recreation 74520SFW-T

Summary of Contents for XDP Recreation 74520SFW-T

  • Page 1 Please retain sales receipt for warranty purposes. DO NOT RETURN THE SET TO THE STORE. If replacement parts or customer service is needed please contact XDP Recreation by email at service@xdprecreation.com or by calling 1-866-884-0535 between 8:00am and 5:00pm (Eastern Standard Time), Monday - Friday. This gym is designed to be used safely by up to eight (8) children, ages 3 years to 8 years, with weight capacity of 100 lbs per child or total combined weight limit of 800 lbs for all eight (8) children (363.6kgs).

  • Page 2: Important Instructions And Warnings

    Anchor kit. If you anticipate severe winds, the product should be moved to a sheltered location or completely disassembled. Anchor kits can be ordered directly from XDP RECREATION at https//:www.xdprecreation.com or by calling 1-866-884-0535.

  • Page 3: Weather Conditions

     DO NOT install your play set over hard surface, e.g. asphalt, concrete, packed earth, tile or brick floor. A fall onto a hard surface can result in serious injury or death to the user. The following is a list of recommended ground covers from the Consumer Product Safety Commission: SUGGESTED MATERIAL UNCOMPRESSED DEPTH...
  • Page 4 PLAY SUPERVISION  DO NOT allow more than one child to play on the individual swing or slide component at any one time. DO NOT allow children to stand on the slide, swing seats, trapeze, seesaw, rocky rider, disc swing or glide ...

  • Page 5: Care And Maintenance Instructions

    INSPECTION PRIOR TO EACH USE OR DAILY INSPECTION  DO NOT use the equipment if any bolts or nuts are missing or loose. ALWAYS check to ensure the equipment and all parts are well secured and stable before each use. ALWAYS clear the play area of any rocks, sharp objects, or any materials that could be potentially ...
  • Page 6 ANCHORING (NOTE: ANCHORS ARE NOT INCLUDED - MUST BE PURCHASED SEPARATELY) There are different ways of anchoring the equipment, depending on the type of ground on which the equipment is to be installed. Make sure that all anchors are below ground level to prevent tripping.
  • Page 7 FRAME LEG 12-5/8” CONCRETE 5” 2” BRICK OR GRAVEL BED Note: The maximum fall height for this product is 4 feet. The minimum ground clearance between the bottom of the suspended plays and the playing or ground surface must be 8 inches. You must maintain a minimum of 8 inches of ground clearance.

  • Page 8: Care And Maintenance Checklist

    CARE AND MAINTENANCE CHECKLIST AT THE BEGINNING OF EACH PLAY SEASON:  Tighten all hardware.  Lubricate all metallic moving parts.  Check all protective coverings on bolts, pipes, edges, and corners. Replace if they are loose, cracked, or missing. ...

  • Page 9: Tools Needed

    TOOLS NEEDED Please prepare the following tools prior to assembling this equipment. Special Socket Wrench Tape Measure (Not included) (Not included) Hammer Wrench (If you intend to install anchor, this is needed) (Included) Wrench Medium Allen Wrench (Not Included) (Included) Flat Head and Philips Head Screwdriver Big Allen Wrench (Not included)
  • Page 10 Part list for main frame assembly LEFT TOP BAR MIDDLE TOP BAR RIGHT TOP BAR TOP SECTION LEG BOTTOM SECTION LEG WITH FOAM CROSS BAR (WITH TWO HOLES) CROSS BAR (WITH FOUR HOLES) Hardware used for main frame assembly BOLT 5/16” (63MM) BOLT 5/16”...
  • Page 11 Part list for swing seat assembly J1-N3 PVC COVERED CHAIN LONG EYE BOLT J3-L (PRE-ASSEMBLED ON J1-N3) ONE EYE BOLT WITH ATTACHMENT BOLT (PRE-ASSEMBLED ON J1-N3) J3-N ***The plastic is Ivory Color.*** K1-F FIREFLY SEAT Hardware used for swing seat assembly NUT 5/16"...
  • Page 12 Part list for SUPER DISC Swing assembly R1-N3 PVC COVERED CHAIN LONG EYE BOLTS R2A-N3 (PRE-ASSEMBLED ON R1-N3) SHORT EYE BOLT R2B-N3 (PRE-ASSEMBLED ON R1-N3) R3-N DISC SWING TUBE DISC SWING TUBE FOAM R3-1 (PRE-ASSEMBLED ON R3-N) DISC SWING FABRIC Hardware used for SUPER DISC Swing assembly F1-N...
  • Page 13 Y4-2W WATER SLIDE B Y5-A HOSE SPRINKLER HEAD Y5-B (PRE-ASSEMBLED ON Y5-A) FEMALE ADAPTER HOSE FITTING Y5-C (PRE-ASSEMBLED ON Y5-A) HOSE CLAMP Y5-D (PRE-ASSEMBLED ON Y5-A) Hardware used for slide assembly PLASTIC CONNECTOR BOLT 1/4" (38MM) Z2-N BOLT 1/4" (97MM) SPRING WASHER CAP NUT 1/4"...
  • Page 14 Part list for Triple Fun-Go Round assembly FRAME CONNECTOR L-SHAPED SUPPORT TUBE UPPER SUPPORT TUBE LOWER SUPPORT TUBE METAL SLEEVE (with PLASTIC SPACER pre-assembled) ROTATING SLEEVE LEFT L-SHAPED LEG (with lower holes) RIGHT L-SHAPED LEG (with higher holes) SEAT SUPPORT HANDLE BAR (with FOAM TUBE pre-assembled) LONGER ANCHOR KIT...
  • Page 15 Hardware used for Triple Fun-Go Round assembly BOLT 5/16" (127MM) BOLT 5/16" (75MM) BOLT 5/16" (63MM) BOLT 5/16" (55MM) BOLT 5/16" (52MM) ARC WASHER 5/16” NUT 5/16” CAP NUT 1/4” BOLT 1/4” (37MM) SPRING WASHER PLASTIC CAP (WITH ARC WASHER) SEAT PLASTIC SPACER (Only 1 is PRE-ASSEMBLED ON Q5)
  • Page 16 ASSEMBLY INSTRUCTIONS  Place the playground equipment on level ground and not less than 6ft (1.8m) from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry line or electrical wires.  Do not install the playground equipment over concrete, asphalt, packed earth or any other hard surface;...
  • Page 17 STEP 1 – Assemble the top bar frame of the swing set  Connect A1, A2 and A3 and secure with B1, B5, B4 and B3 as shown below. Note: All round holes should be facing up and concave holes facing down. Top bar holes FACE UP Concave holes FACE DOWN NOTE:...
  • Page 18 STEP 2 – Assemble the support legs of swing set  Connect A1 to A4.  Repeat this step for the right side of the swing set (A3 and A4). NOTE: Do not over-tighten the nuts and bolts at every step. 2.
  • Page 19 STEP 3 – Assemble the support legs of swing set  Connect A4 to A5 and secure using B1, B5, B4 and B3 as shown below.  Repeat the above step for the right side of the swing set (A3 with A4 & A5). NOTE: Do not over-tighten the nuts and bolts at every step.
  • Page 20 STEP 4 – Attach the crossbar to the support legs  Attach A6 to the outer side of A4 & A5 and secure using B2, B6, B4 and B3. NOTE: Do not over-tighten the nuts and bolts at every step. 2.
  • Page 21 STEP 5 Triple Fun Go Run assembly  Connect Q1 to A1.  Secure using B2, B6, B4 and B3 as shown below. DO NOT RETURN TO RETAILER WHERE YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdprecreation.com...
  • Page 22 STEP 6 – Assemble the support legs of swing set  Connect A3 to A4 and secure using B1, B5, B4 and B3 as shown below.  Connect A5 to A4 as shown below. DO NOT RETURN TO RETAILER WHERE YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdprecreation.com...
  • Page 23  Attach A7 to the outer side of A4 & A5 and secure using B2, B6, B4 and B3. DO NOT RETURN TO RETAILER WHERE YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdprecreation.com...
  • Page 24 STEP 7 – Firefly LED Lighted swing seat assembly (w. "Adjustable Height" Feature) Important: Please make sure to use the J1-N3 with J3-N (the plastic is Ivory Color). This is CRITICAL to other assembly steps.  Connect the Firefly LED Lighted swing seat to the chains by inserting J3-L BLUE MARKING on screw) through K1-F and secure with J7, J9 and J6 as shown in Diagram A.
  • Page 25  Connect swing set chains to the top bar by inserting J3-N through A3, securing with J8 and J6 as shown in Diagram B. Diagram B J3-N J1-N3 Ivory plastic cap J3-L  If you wish to shorten the chain length, follow the below diagram. Diagram C DO NOT RETURN TO RETAILER WHERE YOU PURCHASED AT.
  • Page 26 Battery Installation  Adult installation required!  3 AA Batteries are required but not included. Firefly LED Lighted swing seat 24 Bright, Flashing, Blinking, Strobing Multi-Colored LED LIGHTS The battery Compartment is located on bottom of swing. Two screws are used to secure the Battery Cover. Use #1 Phillips screwdriver to remove screws and cover.
  • Page 27 STEP 8 - "Stand R Swing " seat assembly (w. "Adjustable Height" Feature) Important: Please make sure to use the J1A-N3 with J3A-N (the plastic is Green Color). This is CRITICAL to other assembly steps.  Connect Stand R Swing to the chains by inserting J3A-N3 through K2 and secure with J7A, J9A and J6A as shown in Diagram A.
  • Page 28  Connect Stand R Swing chains to the top bar by inserting J3A-N through A2 & A3 and securing with J8A and J6A as shown in Diagram B. Diagram B J3A-N J1A-N3 Green plastic cap J3A-N3  If you wish to shorten the chain length, follow the below diagram. Diagram C DO NOT RETURN TO RETAILER WHERE YOU PURCHASED AT.
  • Page 29 STEP 9 – Super Disc swing assembly  Separation of foam tube R3-1 from R3-N  Insert the foam tube R3-1 into R4 first, then insert R3 into R3-1 in R4-N.  Slide the smaller ends of R3-N tubes into the pockets of Super Disc swing fabric (R4-N).
  • Page 30 STEP 10 – Attach Super Disc swing to the swing set frame  Connect the chain (R1-N3) to the Super Disc swing by inserting R2B-N3 and securing with F2-N and F1-N as shown in Diagram A.  Connect Super Disc swing to the top bar by inserting R2A-N3 through A1 and A2, securing with F3-N and F1-N as shown in Diagram B.
  • Page 31 STEP 11 - Slide assembly  Connect Y4-1W and Y4-2W and secure with Z10-N (CROSS FLENGE BOLT) and Z6 as shown below. IMPORTANT: Screw in the Z10-N with Z6 onto the middle ridge FIRST. Then screw in the Z10-N and Z6 onto the side ridges of the slide.

  • Page 32: Step 12 - Hose Assembly

    STEP 12 – Hose assembly  Insert Y5-B to the hole on the back of Y4-1W. Y5-B Y4-1W hole DO NOT RETURN TO RETAILER WHERE YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdprecreation.com...
  • Page 33  Secure Y5-B with Z11 as shown below. Y5-B NOTE: Please DO NOT hook up the Y5-A HOSE to your water hose until you have finish the COMPLETE assembly of this product. DO NOT RETURN TO RETAILER WHERE YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdprecreation.com...
  • Page 34 STEP 13 - Slide assembly (continued)  Insert X5-N into the base of Y4-2W.  Secure using Z8, Z6 and Z4.  Attach X4-N to Y4-1W. Note: Make sure that the bolt holes face up. Y4-1W Y4-2W X4-N Bolt holes face up. X5-N NOTE: Do not over-tighten the nuts and bolts at every step.
  • Page 35 STEP 14 - Slide assembly (continued)  Attach X6 to X1-N2 and X2-N2. The inner sides (with concave holes) of both X2-N2 and X1-N2, where X6 (slide ladder steps) is attached to  Secure each side using Z1, Z6 and Z4. ...
  • Page 36 STEP 15 - Slide assembly (continued)  Secure the two sides of the slide using Z2-N, Z6 and Z4, in the sequence shown in the diagram.  Attach X4-N to X1-N2 and X2-N2 and secure using Z1, Z6, Z3 and Z5 as shown in the enlarged diagram.
  • Page 37 STEP 16 - Slide assembly (continued)  Fit Y1 in between X1-N2 and A7 and secure using Y1, Z7, Z6 and Z3, Z5. Important: The sliding direction of the slide should be on the side closer to the two holes on A7, otherwise it may cause the user's hands and clothes to get stuck in the gaps between the swing set frame and slide frame.
  • Page 38 STEP 17 Triple Fun Go Run assembly  Insert Q2 to Q1 and secure using Q14, Q18, Q23 and Q19 as shown below. Now, the parts should look like below diagram after completion of this step NOTE: 1. Do not over-tighten the nuts and bolts at every step. 2.
  • Page 39 STEP 18  Slide Q5 into Q4 and secure using Q12, Q18, Q23 and Q19. Q25 PRE-ASSEMBLED on Q5 Q25 (PLASTIC SPACER) is facing up  Assemble Q25 on both ends of Q6 first. Slide Q28 and Q6 into Q4 as shown IMPORTANT: Please make sure Q28 is assembled.
  • Page 40 STEP 19 Before you start STEP 17, please make sure you have a level ground to assemble Q8 and Q7. The holes on Q8 and Q7 should be aligned to the corresponding holes on Q4. Higher Hole Lower Hole Q8 x2pcs Q7 x2pcs ...
  • Page 41 STEP 20  Insert Q4 into Q3 and secure using Q14, Q18, Q23 and Q19 as shown below. DO NOT RETURN TO RETAILER WHERE YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdprecreation.com...
  • Page 42 STEP 21  Now, connect Q3 to Q2 and secure using Q14, Q18, Q23 and Q19 as shown below. The parts should look like below diagram after completion of this step. NOTE: 1. Do not over-tighten the nuts and bolts at every step. 2.
  • Page 43 STEP 22  Connect Q9 to Q6 and secure using Q16, Q18, Q23 and Q19 as shown below.  Connect Q24 to Q9 and secure using Q21, Q22 and Q20 as shown below. DO NOT RETURN TO RETAILER WHERE YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdprecreation.com...
  • Page 44 STEP 23  Connect Q10 to Q9 and secure using Q15, Q18, Q23 and Q19 as shown below. (Q26 FOAM TUBE is PRE-ASSEMBLED ON Q10) The parts should look like below diagram after completion of this STEP 21. DO NOT RETURN TO RETAILER WHERE YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdprecreation.com...
  • Page 45 STEP 24  Insert the Q27 ANCHOR into the ground until only end of the hook is above the ground and hook onto the L-Shaped Legs. DO NOT RETURN TO RETAILER WHERE YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdprecreation.com...
  • Page 46 STEP 25  Slide at least 8” of the ground tarp slide (the side with grommets) under the slide. Make sure the slide is positioned in the center of the short side of the tarp. Grommet Long side Short side Grommet ...
  • Page 47 Congratulations! You have now completed the swing set assembly. Please make sure to thoroughly check all parts and hardware to make sure all bolts and nuts are well secured before using the playground equipment. WARNING - Do not let children use the playground equipment until it is properly assembled and anchored.

  • Page 48: Customer Support

    What does this Limited Warranty cover? This warranty covers your XDP Recreation product for one hundred and eighty (180) days against defects in material, workmanship, and rust on painted parts which compromise the structural integrity of the product when used for the purpose intended, normal outdoor conditions, and provided it is assembled correctly as illustrated in this manual and receives the proper care and maintenance.
  • Page 49 IF NEEDED, GROUND ANCHORS CAN BE BOUGHT FROM THE STORE YOU PURCHASED THIS SET AT OR BY PURCHASING FROM XDP RECREATION'S WEBSITE AT www.xdprecreation.com XDP RECREATION LLC, 5910 SHILOH ROAD EAST, SUITE 108, ALPHARETTA, GEORGIA 30005 REGISTER YOUR “XDP” PURCHASED PRODUCT PLEASE VISIT OUR WEBSITE at www.xdprecreation.com to register your...

Table of Contents