Download Print this page

Advertisement

Quick Links

This addendum addresses European Union (EU) Ecodesign requirements for servers and storage
products. All data and ratings within this addendum are in reference only to the Supermicro product(s) in
the manual. The below information conforms to requirements laid down in Annex II of the Commission
Regulation 2019/424.
3(1)(a):
See Section 1.1 of the system manual for the product type.
3(1)(b):
See the title page and preface of the system manual for the trademark and
manufacturer's address.
3(1)(c):
See the title page of the system manual for product model number(s).
3(1)(d):
See the serial number on the physical system to determine the year of manufacture.
3(1)(e-j):
PSU Efficiency and Power Factor Value (Table) (From 80 Plus report)
PSU Model #:
PWS-1K66P-1R
Watts: 1600
% of Rated Load
Single Output (AC-DC)
System (EUT) Efficiency in
Representative
Configurations
High-End Performance
Configuration
Typical Configuration
Low-End Performance
Configuration
System (EUT) Efficiency in
Representative
Configurations
High-End Performance
Configuration
Typical Configuration
Low-End Performance
Configuration
Information for Lot 9 of ErP (Ecodesign)
10 %
91.60 % 93.84 %
Idle State
Measured Idle State
Power (W)
453.9
N/A
105.4
Active State
Active State
Efficiency Score
(Effserver)
11.8
N/A
12.6
PSU Efficiency
20 %
50 %
100 %
94.30
91.23%
%
Power (Table)
Calculated Idle Power
Allowance (W)
504.07
N/A
168.63
Power (Table)
Minimum Active State
Efficiency
9
Power Factor
50 %
0.99

Advertisement

loading

Summary of Contents for Supermicro SSG-5049P-E1CR45L

  • Page 1 This addendum addresses European Union (EU) Ecodesign requirements for servers and storage products. All data and ratings within this addendum are in reference only to the Supermicro product(s) in the manual. The below information conforms to requirements laid down in Annex II of the Commission Regulation 2019/424.
  • Page 2 The first is with a Unified Extensible Firmware Interface (UEFI) shell utility. This utility works on X10/X11/H11/H12/M11 motherboard series with onboard SATA/NVMe devices. Any user may access and download this utility through following link: https://www.supermicro.com/about/policies/disclaimer.cfm?url=/wftp/utility/Lot9_Secure _Data_Deletion_Utility/ Download the shell utility package and extract it to a USB flash drive, then plug the drive into the server for which secure data deletion is necessary.
  • Page 3 The indicative weight range of neodymium in the HDD is 0.0 if manufactured by Western Digital, and is between 5-25 grams if manufactured by Seagate. 3(3)(b): Please see the disassembly instructions on the next page.
  • Page 4: Data Storage Devices

    Illustrated System Disassembly Instructions Please note: All the illustrations in the below disassembly instructions are for demonstration only. Components shown here may not match exactly with the components in your system. CAUTION: Always power off the system and unplug the power cord(s) first before disassembling the system! 1.
  • Page 5 2. Memory Type and number of fastenings: Two (2) latches per memory module. Tools required: None. Procedure: Press both release tabs on the ends of the memory module to unlock it. Once the module is loosened, remove it from the memory slot.
  • Page 6 3. Processor Type and number of fastenings: Four (4) T30 Torx screws. Tools required: Screwdriver with T30 Torx bit. Procedure: Remove the screws in the sequence of 4, then 3, then 2, then 1, as marked in the illustration below. After removing the screws, lift the processor heatsink module off the processor socket.
  • Page 7 4. Motherboard Type and number of fastenings: Three (3) thumb screws, 10 Phillips screws, and three (3) fan housings and airshroud to expose the motherboard. Nine (9) Phillips screws to remove the motherboard. Tools required: Screwdriver with PH2 bit. Procedure: (Fig.
  • Page 8 Fig. 3 Fig. 4...
  • Page 9: Expansion Card

    5. Expansion Card Type and number of fastenings: One (1) Phillips screw and two (2) latches. Tools required: Screwdriver with PH2 bit. Procedure: Remove the Phillips screw. Then pull the card out while applying pressure on the latches as shown by the two arrows below.
  • Page 10: Power Supply Module

    6. Power Supply Module Type and number of fastenings: One (1) latch per module. Tools required: None. Procedure: Unplug the power cord from the power supply. Push the release tab on the back of the power supply module to the side and pull the module straight out.
  • Page 11: Chassis Cover

    7. Chassis Cover Type and number of fastenings: Two (2) thumb screws. Tools required: None. Procedure: Unscrew the two thumb screws, then lift away the top cover.
  • Page 12 8. Batteries Type and number of fastenings: One (1) latch. Tools required: None. Procedure: Push aside the small clamp that covers the edge of the battery. When the battery is released, lift it out of the holder. 9. Fans Type and number of fastenings: Two (2) latches per fan.