Advertisement
Contents Checklist
Please check the components after unpacking. If any are missing, or if there is a page missing from the product manual, etc., please contact the dealer.
| Part |  |
| A80 Countertop Payment Terminal |  |
| AC Power Adapter | |
| AC Power Cable | |
| Telephone Cable | |
| Thermal Paper Roll | |
| Quick Setup Guide | |
Product Description
Figure 1. Front view
Figure 2. Back view
- Printer Cover
- Contactless Area & Printer Latch
- Main Screen
- MSR Reader
- Power ON/OFF
- EMV/Chip Reader
- Cable Guides
- USB Host (Port)
- Power (Port)
- PIN Pad (Port)
- RS232 (Port)
- Serial Number
- Nameplate
- SD Card Slot
- SAM Slots
- Line (Port)
- Phone (Port)
- LAN (Port)
- USB OTG (Port)
Instructions
The following sections cover basic operating instructions.
Power ON/OFF
POWER ON:
Press and hold the power button down for 3-5 seconds and then release.
POWER OFF:
Press and hold the power button down for 3 to 5 seconds and then release.
SAM/SD Card Installation
Figure 3.SAM and SD Card Slots
The A80 has two SAM card slots on the main body of the device and one SD card slot. These card slots are normally hidden under the back cover.
In order to install a SD or SAM card into any of these slots, insert a card into the card slot with the contacts facing upwards and the clipped corner of the card facing forward and to the right.
Card Readers
- Magnetic Stripe Card: Slide the card through the card reader slot from top to bottom or from bottom to top with the magnetic strip oriented towards the body of the device. Make sure that the card is fully inserted into the card reader while swiping the card.
- Smart Card Reader: Insert the card fully into the reader with the metallic contacts facing up and towards the device. Make sure that the card is fully inserted into the card reader while scanning the card.
- Contactless Card Reader: The contactless card reader reads cards and devices placed roughly within an inch (2.5 mm). For best results, place as close to the reader as possible and center the card over the indicated area.
Environment
Working Environment:
Temperature: -10°C ~ 50°C (14°F ~ 122°F)
Humidity: 10% ~ 93% (without condensation)
Storage Environment:
Temperature: -20°C ~ 70°C (-4°F ~ 158°F)
Humidity: 10% ~ 93% (without condensation)
Cleaning the Device
- Do not use industrial strength or abrasive cleaner as it may damage or scratch the screen.
- Do not immerse the device in water or liquid.
- Do not spray water or cleaner into EMV Card Reader or ports.
- To clean the screen, apply distilled water or mild glass cleaner onto a soft, lint-free cloth and gently wipe terminal.
Terminal Installation and Usage Tips
- If any cables become damaged, seek a replacement.
- Do not insert unknown materials into any port on the A80; this may cause serious damage.
- If repairs are required, please contact a professional technician instead of attempting them on your own.
- Avoid exposing the device to an excessively hot, dusty, or strong electromagnetic envrionment.
- Do not vibrate, shake, or drop the device.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
PAX Customer Support
For questions or help with the terminal installation please contact your service provider or PAX customer support.
Responsible Party:
PAX Technology, Inc.
8880 Freedom Crossing Trail
Building 400, 3rd Floor, Suite 300
Jacksonville, FL 32256, USA
Help Desk 1-877-859-0099
www.pax.us
Documents / Resources
References
Download manual
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Advertisement
Need help?
Do you have a question about the A80 POS and is the answer not in the manual?
Questions and answers