Atp32U04 - ClimateMaster ATM11C11 Submittal Data

6.25"
[159mm]
4.25"
[108mm]
1.25" Depth
[32mm]
Mounting:
UP
1.50" 3.25"
[38mm] [83mm]
Application:
The ATP32U04 Thermostat provides 3 stages heating,
2 stages of cooling, and programmable temperature/
humidity control of 24V water-source heat pump
equipment.
Features:
• Dehumidification output is designed to work with
Whole House Dehumidification Modulating Reheat
option or with ECM fan motor dehumidification mode
• Integrated control of both temperature and relative
humidity
• Integrated control eliminates separate thermostat and
dehumidistat/humidistat
• Thermostat can be programmed to use humidification
output to control a humidifier
• Night Setback mode initiated by an external signal
(when using a DXM controller).
ClimateMaster works continually to improve its products. As a result, the design and specifi cations of each product at the time of order may be changed without notice and may not be as described herein. Please contact ClimateMaster's Customer
Service Department at 1-405-745-6000 for specifi c information on the current design and specifi cations. Statements and other information contained herein are not express warranties and do not form the basis of any bargain between the parties,
but are merely ClimateMaster's opinion or commendation of its products. The latest version of this document is available at climatemaster.com.
LC204 - 9
Thermostat Submittal Data
.62"
[16mm]
3.00"
[76mm]
0.62"
[16mm]
Rev.: 28 February, 2013
Three Heat / Two Cool,
Auto / Manual Changeover
Programmable (7 Day) - With Humidity Control
Features (cont.):
• Four periods per day
• ºF or ºC temperature display
• 12 or 24 hour clock
• Individual heat and cool setpoints
• Zero temperature droop performance
• Automatic (program mode) or manual (HOLD) operation
• 7-day programming.
• Convenient overrides allow temporary setpoint changes
• Setpoints are permanently held in memory (no batteries
used) and retained during power outages
• Room temperature offset adjustment
• Progressive Recovery anticipates the time required to
bring the space temperature to the next programmed
event, and brings on the heat pump accordingly
• Large backlit dot matrix display is activated whenever a
key is pressed and remains on for 25 seconds
• Menu-driven programming with five navigation buttons
(UP/DOWN/LEFT/RIGHT/SELECT) for ease of use
• Fault indication with red backlight display
• Configurable service interval messages and servicing
contractor contact information
• Keypad lockout
• Back-plate wiring connections for easy installation
• Exclusive fault identification (When used with CXM
or DXM) displays fault from CXM/DXM board (e.g.
condensate overflow) and suggests possible causes
• Compatible with optional AST008C sensor for use
as remote and/or outdoor sensor, or for indoor wall
mounted sensor use ASW06.
Specifi cations:
Electrical Rating:
• Input Power: 18 to 30 VAC, 50/60 Hz
Operating Conditions:
• 32ºF to 104ºF [0ºC to 40ºC]
• 10% to 95% non-condensing
Temperature Settings:
• Setpoint range: 55ºF to 95ºF [12ºC to 35ºC], +/- 2ºF [1ºC]
• Dehumidification setpoint range: 15% to 95% RH
• Humidification setpoint range: 10% to 45% RH
Output Ratings:
• Maximum current for each output is 1.0 Amp (2.0 max.
output total).
Eng/I-P

ATP32U04

Page ______ of ______