Table of Contents
Advertisement
Non-Programmable
Heat Pump Thermostat
Installation Manual
97B0082N06
Revised: 16 September, 2013
FOR INSTALLER
AND OWNER ONLY
Table of Contents
Display Lighting
Remote Sensor Temperature Display
Equipment Outputs
3
3
3
3
3
3
3
4
5-8
5
5
8
8
8
8
8
9
9
9
9
9
9
9
10
10
10
10
10
10
10
10
10
11
12
Advertisement
Table of Contents
Related Manuals for ClimateMaster ATA11U03
Summary of Contents for ClimateMaster ATA11U03
-
Page 1: Table Of Contents
Table of Contents ATA11U03 Safety Considerations General Package Contents Installation Considerations Power Wiring Thermostat Location Installation Configuration Entering and Exiting Configuration Mode Configuration Options Exiting Configuration Mode System Start-Up and Checkout Installer Test Mode Terminating Installer Test Checklist Operation Mode Selection Fan Selection Non-Programmable Fan Display Set Temperature Selection Heat Pump Thermostat Display Lighting Remote Sensor Temperature Display Timers Five-Minute Compressor Timeguard Installation Manual Minimum On Timer... - Page 2 W A T E R - S O U R C E H E A T P U M P S ATA11U03 R e v. : 0 9 / 1 6 / 1 3 This Page Intentionally Left Blank...
-
Page 3: Ata11U03
T H E S M A R T S O L U T I O N F O R E N E R G Y E F F I C I E N C Y ATA11U03 R e v. : 0 9 / 1 6 / 1 3... -
Page 4: Installation
W A T E R - S O U R C E H E A T P U M P S ATA11U03 R e v. : 0 9 / 1 6 / 1 3 Installation Installation - To install the thermostat, perform the the thermostat. -
Page 5: Configuration
T H E S M A R T S O L U T I O N F O R E N E R G Y E F F I C I E N C Y ATA11U03 R e v. : 0 9 / 1 6 / 1 3... - Page 6 W A T E R - S O U R C E H E A T P U M P S ATA11U03 R e v. : 0 9 / 1 6 / 1 3 Configuration OPTION 07 — EQUIPMENT DDC CONTROLLER —...
- Page 7 T H E S M A R T S O L U T I O N F O R E N E R G Y E F F I C I E N C Y ATA11U03 R e v. : 0 9 / 1 6 / 1 3 Configuration have full access to the thermostat functionality. The...
-
Page 8: Exiting Configuration Mode
W A T E R - S O U R C E H E A T P U M P S ATA11U03 R e v. : 0 9 / 1 6 / 1 3 will be displayed in the set-point location. Pressing the fan button alternates the fan selection To initiate factory defaults, the installer then presses the between fan auto and fan on and the fan output follows mode button until the 10 is flashing. The installer then accordingly. -
Page 9: Operation
T H E S M A R T S O L U T I O N F O R E N E R G Y E F F I C I E N C Y ATA11U03 R e v. : 0 9 / 1 6 / 1 3 OPERATION Set Temperature Selection — If auto mode is not... -
Page 10: Timers
W A T E R - S O U R C E H E A T P U M P S ATA11U03 R e v. : 0 9 / 1 6 / 1 3 Timers — There are several timers which influence the WIRING DIAGRAMS thermostat’s operation that are listed below. If any of the System wiring diagram is shown for typical ClimateMaster timers is preventing the equipment from turning on, the heat pump unit. See Fig. 7. -
Page 11: Thermostat Configuration Record
T H E S M A R T S O L U T I O N F O R E N E R G Y E F F I C I E N C Y ATA11U03 R e v. : 0 9 / 1 6 / 1 3... -
Page 12: Revision History
W A T E R - S O U R C E H E A T P U M P S ATA11U03 R e v. : 0 9 / 1 6 / 1 3 Revision History Date: Item: Action:...