Table of Contents
Advertisement
NW-A35/A35HN/A36HN/A37HN
Ver. 1.1
Procedure:
1. On PC, unzip the advance prepared each settings/checking
tools.
2. Copy the unzip folder to root directory of C drive on PC.
Note 5: The folder can be saved any drive as long as the folder path is
with English (one byte character).
Described with the example that "the folders were saved under
root directory of C drive" on this service manual.
2. Settings
Settings/checks according to the following order.
Destination/model settings (use for the destination/model set-
tings tool)
r
Initial settings (use for the initial settings tool)
r
Model information check (use for the model information check
tool)
r
Pre-installed contents settings (use for the pre-installed con-
tents/transfer tools)
2-1. Destination/model settings
Perform settings of the destination, headphones and each model
etc.
The initial setting of the factory shipment is different on the des-
tination, model and headphones bundled or not bundled to the
WALKMAN main unit.
Be sure to refer to "METHOD OF DISTINGUISHING THE
WALKMAN MAIN UNIT" on page 4 in advance.
Note 1: Contents those have been recorded in this unit all will be erased.
Used folder name (tool):
For NW-A35:
US, CND:
NWA30_UC_NOHP_ChangeDestination_V1.00
CEW:
NWA30_CEW_NOHP_ChangeDestination_V1.00
E (Including for Korea):
NWA30_E_NOHP_ChangeDestination_V1.00
CH:
NWA30_CN_NOHP_ChangeDestination_V1.00
EE:
NWA30_EE_NOHP_ChangeDestination_V1.00
For NW-A35HN/A36HN/A37HN:
US, CND:
NWA30_UC_HRNC_ChangeDestination_V1.00
CEW (Including for Korea):
NWA30_CEW_HRNC_ChangeDestination_V1.00
E:
NWA30_E_HRNC_ChangeDestination_V1.00
CH:
NWA30_CN_HRNC_ChangeDestination_V1.00
EE:
NWA30_EE_HRNC_ChangeDestination_V1.00
LA:
NWA30_LA_HRNC_ChangeDestination_V1.00
Note 2: Korean model is depending on the model type, and the tool of the
different destination to be used.
Note 3: Please refer to "DESTINATION ABBREVIATIONS" on page 4
for the sales country or area of each destination.
IMPORTANT:
Be sure to use the destination/model settings tool select the
correct destination. It is a compliance violation to change the
destination to other regions.
6
Procedure:
1. Connect the WALKMAN main unit to PC (personal computer)
by the USB cable (WM-PORT).
(The power supply of the WALKMAN is automatically turned
on)
– The following steps will all operate on the PC (personal com-
puter) –
2. Check how the WALKMAN is recognized by MSC connec-
tion, and the check of the drive letter is necessary.
(at this example, it is "F:")
3. Open the folder that the destination/model settings tool.
4. In the non-selected state for fi les in the folder, and put a cursor
to blank space in the folder.
In the folder of the destination/model settings tool
5. The right-click while pressing the Shift key in the state of step
4.
6. Select the "Open command window here" from the displayed
menu, and launch the command prompt application software.
7. Input the following command and press the Enter key.
"updating.bat f:"
("f:" is drive letter of checked at step 2)
C:\NWA30_XXX_XXXX_ChangeDestination_V1.00>updating.bat f:
Destination
"NOHP" or "HRNC"
USB cable
drive letter
blank space
cursor
Input
– Continued on next page –
Advertisement
Table of Contents
