Table of Contents
Advertisement
5-4-4. Base noise canceling gain (R-ch) setting
(Base NC gain-R)
It can be setting the base noise canceling gain value (R-ch).
Procedure:
1. Enter the test mode.
(Refer to "2. SETTING THE TEST MODE" on page 29)
2. Press the [+]/[–] keys to select the "Noise cancel", and press
the [
] or [
] key to enter the minor item.
u
>
3. Press the [+]/[–] keys to select the "Base NC gain-R".
4. Press the [
] key, the base noise canceling gain value (R-ch)
u
is displayed.
(Displayed value in the following fi gure is example)
Screen display
NC Base NC gain (R)
(NOC BGNR command)
NC Base NC gain (R)
[31]
5. In step 4 state, each time the [
base noise canceling gain value (R-ch) is selected. (0 to 50)
6. Press the [
] key, and decision of the base noise canceling
u
gain value (R-ch).
Note: The setting is not saved with this test item. Refer to "5-4-5. Base
noise canceling gains save" to save.
7. Slide the [HOLD] switch in the direction of on, to return to
minor item selection screen.
5-4-5. Base noise canceling gains save
(Save base NC gain)
It can be save of settings for "5-4-3. Base noise canceling gain (L-
ch) setting" and "5-4-4. Base noise canceling gain (R-ch) setting".
Procedure:
1. Enter the test mode.
(Refer to "2. SETTING THE TEST MODE" on page 29)
2. Press the [+]/[–] keys to select the "Noise cancel", and press
the [
] or [
] key to enter the minor item.
u
>
3. Press the [+]/[–] keys to select the "Save base NC gain".
4. Press the [
] key, the setting screen is displayed.
u
(Displayed value in the following fi gure is example)
Screen display
Base NC gain save
(NOC BGNS command)
NC Base NC gain
Left
Right
>>> set
5. Press the [
] key, and save of settings for base noise cancel-
u
ing gain value (L/R-ch).
6. Slide the [HOLD] switch in the direction of on, to return to
minor item selection screen.
Base noise canceling
gain value
]/[
] keys are pressed,
.
>
[30]
[31]
NW-A35/A35HN/A36HN/A37HN
5-4-6. User noise canceling gain setting (User NC gain)
It can be setting the user noise canceling gain value.
Procedure:
1. Enter the test mode.
(Refer to "2. SETTING THE TEST MODE" on page 29)
2. Press the [+]/[–] keys to select the "Noise cancel", and press
the [
] or [
] key to enter the minor item.
u
>
3. Press the [+]/[–] keys to select the "User NC gain".
4. Press the [
] key, the setting screen is displayed.
u
Screen display
NC User NC gain
(NOC UNGN command)
NC User NC gain
[15]
5. In step 4 state, each time the [
user noise canceling gain value is selected. (0 to 30)
6. Press the [
] key, and decision of the user noise canceling
u
gain value.
7. Slide the [HOLD] switch in the direction of on, to return to
minor item selection screen.
5-4-7. Noise canceling status check (Get NC status)
It can be check the on/off status of the noise canceling mode.
Procedure:
1. Enter the test mode.
(Refer to "2. SETTING THE TEST MODE" on page 29)
2. Press the [+]/[–] keys to select the "Noise cancel", and press
the [
] or [
] key to enter the minor item.
u
>
3. Press the [+]/[–] keys to select the "Get NC status".
4. Press the [
] key, the status of the noise canceling mode is
u
displayed.
Screen display
NC status
(NOC GNCS command)
NC status
[0]
5. Slide the [HOLD] switch in the direction of on, to return to
minor item selection screen.
5-5. Direct recording (Direct Rec)
Note: This major item is not used for the servicing.
5-6. Bluetooth safety test (BT safety test)
Note: This major item is not used for the servicing.
5-7. Bluetooth test tools (BT test tools)
Note: This major item is not used for the servicing.
User noise canceling
gain value
]/[
] keys are pressed,
.
>
0: Noise canceling off
1: Noise canceling on
37
Advertisement
Table of Contents
