Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for LINOVISION IOT-S500L
Summary of Contents for LINOVISION IOT-S500L
- Page 1 IOT-S500L LoRaWAN® PIR & LightSensor Updated on Sept. 10, 2021...
- Page 2 ❖ The device is not intended to be used as a reference sensor, and Linovision will not take responsibility for any damages which may result from inaccurate readings. When installing the battery, please install it accurately, and do not install the reverse or ❖...
- Page 3 Revision History Date Doc Version Description July 15,2021 V 1.0 Initial version 1. Add LoRa D2Dfeature; 2. Support light collection enabled/disabled; Sept. 10, 2021 V 1.1 3. Delete low power alarm interval, device only uplinks once when battery level is lower than 10%.
-
Page 4: Table Of Contents
Contents 1. Product Introduction ............................ 5 1.1Overview .............................. 5 1.2Features ...............................5 2. HardwareIntroduction..........................5 2.1Packing List ............................5 2.2HardwareOverview ..........................6 2.3Dimensions............................6 2.4LED Patterns............................6 3. OperationGuide .............................7 3.1NFC Configuration..........................7 3.2LoRaWAN Settings..........................7 3.3GeneralSettings..........................10 3.4ThresholdSettings ..........................11 3.5LoRa D2DSettings..........................1 1 3.6Maintenance ............................. -
Page 5: Product Introduction
IOT-S500L can detect whether there is a movement within the range of 6-8m. Besides, IOT-S500L equips with a light sensor which can link PIR detection results to trigger scenes. IOT-S500L can be widely used in smart homes, smart offices, schools, warehouses, etc. -
Page 6: Hardwareoverview
2.2 Hardware Overview 2.3 Dimensions (mm) 2.4 LED Patterns Function Action LED Indicator PIR is triggered (network unregistered) Red, blink once PIR Detection PIR is triggered (network registered) Green, blink once Send join network requests Red, blinks once Network Status Joined the network successfully Green, blinks twice Reboot... -
Page 7: Operationguide
2) If the smartphone fails to read/write configurations via NFC, move the phone away and back to try again. 3) IOT-S500L can also be configured by ToolBox software via a dedicated NFC reader provided by IoT, you can also configure it via TTL interface inside the device. - Page 8 Basic LoRaWAN Settings: Go to Device ->Setting ->LoRaWAN Settings of ToolBox App to configure join type, App EUI, App Key and other information. You can also keep all settings by default. Parameters Description Device EUI Unique ID of the device which can also be found on the label. App EUI Default App EUI is 24E124C0002A0001.
- Page 9 specific packets are being sent, the device will re-join. ADR Mode Allow network server to adjust data rate of the device. Tx Power Transmit power of device. Note: 1) Please contact sales representative for device EUI list if there are many units. 2) Please contact sales representative if you need random App keys before purchase.
-
Page 10: Generalsettings
The interval of reporting PIR, light status and battery level to network server. Default: 30 mins, Range: 1 -1080 mins Reporting Interval Note: IOT-S500L will also report “triggered” status of PIR sensor immediately when it detects motions. Idle Time When the PIR sensor does not detect motion for a period of Idle Time,... -
Page 11: Thresholdsettings
When illuminance collection is enabled, users can define the Bright or Dark state via detection data of light sensor in threshold settings. Besides, when the PIR sensor is triggered and light status meets the threshold, IOT-S500L will send alarms immediately. Otherwise, it will not send data rightaway. -
Page 12: Maintenance
3. Enable one of IOT-S500L status and configure a 2-bytehexadecimal command (This command is pre-definedin LoRa D2D agent device). When IOT-S500L detects this status, it will send the control command to corresponding LoRa D2Dagent devices. ® Note: When this feature is enabled, the device will not send data to LoRaWAN network server if IOT-S500L PIR or lightstatus changes. -
Page 13: 3Reset To Factory Default
1. Go to “Template” page on the App and save current settings as a template. You can also edit the template file. 2. Select one template file that saved in the smartphone and click “Write”, then attach it to another device to write configuration. Note: Slide the template item to the left to edit or delete the template. -
Page 14: Installation
Note: 1. Adjust the installation direction according to detection area requirement. 2. IOT-S500L can be mounted on a wall or ceiling. Itʼs recommended to install at 1.5~2.5m from the floor. 3. Ensure the detection area does not have moving objects like waving trees and fans. -
Page 15: Basic Information
5.2 Sensor Data IOT-S500L reports sensor data and battery level according to reporting interval (30 mins by default) or when PIR or light status changes. Besides, when battery level is lower than 10%, it will upload battery pakcage once. -
Page 16: Downlinkcommands
Channel Type Value 00 (Light 01=>Bright Status) 5.3 Downlink Commands IOT-S500L supports downlinkcommands to configure the device. The application port is 85 by default. Channel Type Description 03 (Set Reporting Interval) 2 Bytes, unit: s Example: Set reporting interval as 20 minutes.