Download Print this page

Felix Storch Pro L Series Service Manual

Hide thumbs Also See for Pro L Series:

Advertisement

Quick Links

How to replace Pro 3 Printhead
15 April 2022
FELIX Pro L and XL
Revision 0
series

Advertisement

loading
Need help?

Need help?

Do you have a question about the Pro L Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Felix Storch Pro L Series

  • Page 1 How to replace Pro 3 Printhead 15 April 2022 FELIX Pro L and XL Revision 0 series...
  • Page 2 Pro L XL series How to replace Pro 3 Printhead 15 April 2022 1 Introduction This manual explains how to replace the Pro 3 printhead properly. 2 Tools The tools you need to replace the build plate of the Pro L and XL: •...
  • Page 3 Pro L XL series How to replace Pro 3 Printhead 15 April 2022 2) Disconnect the ribbon cables at the printhead Disconnect the ribbon cables. Be careful to not destroy the connectors. Red circles You can use tweezers. 3) Disconnect the servo cable at the printhead Disconnect the servo cable.
  • Page 4 Pro L XL series How to replace Pro 3 Printhead 15 April 2022 4) Remove sensor bolts Loosen the bolts with an allen key 2,5. Red circles. 5) Remove the bracket bolts Loosen the bolts with an allen key 2,5. Red circles.
  • Page 5 Pro L XL series How to replace Pro 3 Printhead 15 April 2022 6) Remove the wiring on the PCB carefully remove all the wiring inserted in the extruder PCB. You can use an tweezer to make is easier. Red circles. 7) Remove the 2 top bolts Remove the 2 bolts using an allen key 2,5.
  • Page 6 Pro L XL series How to replace Pro 3 Printhead 15 April 2022 8) Remove the side bolt Remove the bolt that holds the 2 printhead assemblies together using an allen key 3. circle. 9) Take off the old printhead Carefully take off the printhead.
  • Page 7 Pro L XL series How to replace Pro 3 Printhead 15 April 2022 4 Assemble new printhead 1) Take the new printhead Take off the new printhead from the transport block. Place the old printhead on this transport block when done. Watch out because the 2 heads are attached to each other with the cables 2) Place the new printhead When slicing the new printhead on the bracket make sure no cables get stuck.
  • Page 8 Pro L XL series How to replace Pro 3 Printhead 15 April 2022 3) Place the right printhead Start with sliding the left printhead on the bracket. Keep in mind when you slide the right printhead on the bracked to get the servo pin in the pocket. circle.
  • Page 9 Pro L XL series How to replace Pro 3 Printhead 15 April 2022 5) Place the 2 top bolts Place and tighten the 2 bolts using an allen key 2,5. Red circles. 6) connect the wiring on the PCB carefully connect all the wiring to the extruder PCB. You can use an tweezer to make is easier.
  • Page 10 Pro L XL series How to replace Pro 3 Printhead 15 April 2022 7) Place the bracket bolts Place the bolts with an allen key 2,5. Red circles. 8) Place sensor bolts Place the bolts with an allen key 2,5. Red circles.
  • Page 11 Pro L XL series How to replace Pro 3 Printhead 15 April 2022 9) Connect the ribbon cables at the printhead Connect the ribbon cables. Be careful to not destroy the connectors. Red circles You can use tweezers. Connect the servo cable at the printhead Connect the servo cable.
  • Page 12 Pro L XL series How to replace Pro 3 Printhead 15 April 2022 5 Heater check 1) Temperatures Info: reinstall the ribbon cables into the connector if it doesn’t! Check if the printer can read the hotend temperatures. 2) Homing Hit move.
  • Page 13 Pro L XL series How to replace Pro 3 Printhead 15 April 2022 Hit “home all”. If it doesn’t home correctly. Turn off the printer and try to reinsert the cables. www.FELIXprinters.com FELIX Pro L XL...
  • Page 14 Pro L XL series How to replace Pro 3 Printhead 15 April 2022 6 Levelling Info: Do all calibrations before staring a Dual head print! 1) Build plate leveling Press “printer calibration”. Press “bed leveling”. www.FELIXprinters.com FELIX Pro L XL...
  • Page 15 Pro L XL series How to replace Pro 3 Printhead 15 April 2022 Hit “yes” to start the bed leveling. The bed leveling is done when you see this message. Hit “ok”. www.FELIXprinters.com FELIX Pro L XL...
  • Page 16 Pro L XL series How to replace Pro 3 Printhead 15 April 2022 2) Z-calibration Press “printer calibration”. Press “Calibrate Z”. www.FELIXprinters.com FELIX Pro L XL...
  • Page 17 Pro L XL series How to replace Pro 3 Printhead 15 April 2022 Press “Yes”. Press “Ok”. www.FELIXprinters.com FELIX Pro L XL...
  • Page 18 Pro L XL series How to replace Pro 3 Printhead 15 April 2022 3) XY-calibration Press “printer calibration”. Press “Calibrate XY”. www.FELIXprinters.com FELIX Pro L XL...
  • Page 19 Pro L XL series How to replace Pro 3 Printhead 15 April 2022 Load in PLA in both hotends and hit “Yes”. Make sure line 5 matches both nozzles for the X and Y. Does it not? then enter the number where the lines do match and start the calibration again.
  • Page 20 Pro L XL series How to replace Pro 3 Printhead 15 April 2022 If you are unable to continue or have any questions, you can check at the support section of our website or you can contact us directly: Website: www.felixprinters.com/support Email: support@felixprinters.com...

This manual is also suitable for:

Pro xl series