1. Warning and precautions for safety Please observe the following safety precautions in order to use safely and correctly the refrigerator and to prevent accident and danger during repair. 1. Be care of an electric shock. Disconnect power cord from wall outlet and wait for more than three minutes before replacing PCB parts.
2. Appearance and structure 2.1 View of the appliance Note! Due to unceasing modification of our products, your refrigerator may be slightly different ● from this instruction manual, but its functions and using methods remain the same. To get the best energy efficiency of this product, please place all shelves, drawers and baskets on their original position as the illustration above.
4.2 Using the appliance ● This section tells you how to use most of the useful features. We recommend that you read through them carefully before using the appliance. Getting cold water The water dispenser is located in the left side of fridge room. Open the refrigerator doors, and push the water dispenser button to get water,.
Page 12
3. Insert the new filter into the filter holder. 4. Push the filter, and then turn it clockwise until it locks. If you have trouble inserting the water filter because of high water pressure, shut off the Hisense Refrigerator...
Page 13
To remove the door baskets, simply lift the racks up and pull straight out. To relocate the door baskets, slide it in above the desired location and push down until it stops. Hisense Refrigerator...
Page 14
Then pull out the draw and tilt up the front of the crisper after moving slightly in the directing of the arrow. Using the freezer compartment The freezer compartment is provided with an upper drawer, a lower drawer and a ice box. ● Hisense Refrigerator...
Page 15
3. Take out the upper freezer drawer (A) by lifting it up from the rail system. 4. Remove the lower freezer drawer (C) by lifting it up. ● 5. Remove the 4 screws attached to the supporting frame (D). Hisense Refrigerator...
Page 16
● parts in reverse order. Remove the ice maker part 1. Open freezer door, take upper drawer out. 2. Disassemble two fixed screws with a cross screwdriver (+). 3. Pull out the ice maker part. Hisense Refrigerator...
Page 17
4. Unplug two terminals, then take out the ice maker part. Remove the water pipe connector part 1. Remove the ice maker part ● 2. Unplug the terminal. Hisense Refrigerator...
Page 18
(+), then pull the ice maker inlet ● cover down. 5. Pull the blue water tube out in the direction of arrow. 6. Disassemble the fixed screw with a cross screwdriver (+). 7. Pull the water pipe connector part out with pliers. ● Hisense Refrigerator...
No.4 Measuring the 0.8V~4.6V Ice maker voltage between sensor the Main PCB malfunctions CN5 PIN No.11- No.12 Under ice tray forced to turn, measuring the Ice maker ● voltage between malfunctions the Main PCB CN5 PIN No.7- No.8 Hisense Refrigerator...
Page 22
3. Replace the door switch. 4. Replace the control PCB. 1. Checking the compressor is High working or not. temperature in 2. Refrigerator the refrigerator sensor compartment Refrigerator sensor ● Hisense Refrigerator...
Page 24
No. 1 and No.3 on CN9 connector of main- ● board. 5. Humidity sensor corresponding pin No. 1 and No. 4 on CN9 connector of main-board. 6. Ice maker sensor corresponding pin No.11 and No. 12 on CN5 connector of main- board. Hisense Refrigerator...
Page 25
GND) and negative rotating(white wiring connect power, red wiring connect GND) normally or not. If it is abnormal, change the ice maker or mainboard. 4.4.2.5. Communication error ● Ec or Er error: Hisense Refrigerator...
Page 26
If not , change the freezer fan motor. Pin No.2 connect 12V power and pin No.1 connect GND, if the condenser fan motor works normally, change the main-board; If not , change the condenser fan motor. Hisense Refrigerator...
Page 27
Check the water supply whether ok, if water supply is ok then check the connecting wire. The flow sensor corresponding pin No. 9~11 on CN7 connector of main-board, as the drawing below. If the wire is broken, repair the wiring otherwise change the main- board or the water valve. Hisense Refrigerator...
Doors are kept open too long or too often. After your installing the appliance or it has been switched off for a long time. A layer of frost occurs in Check that the air outlets are not blocked by food and ensure Hisense Refrigerator...
Page 29
Check if the filter is properly installed. If it is not properly installed, the water dispenser may not work. Is the Child Lock on? Hear water bubbling in This is normal. The bubbling comes from the refrigerant the refrigerator coolant liquid circulating through the refrigerator. Hisense Refrigerator...
Is the appliance too close to heat sources? Make enough distance between heat sources ● and appliance Is watery or hot food stored in the cabinet? Wipe out dew on the louver surface and run the refrigerator again Hisense Refrigerator...
Is the appliance too close to heat sources? Make enough distance between heat sources and appliance Is watery or hot food ● stored in the cabinet? Advise to cool down hot food and seal watery food well before storing Hisense Refrigerator...
Pin No.5)connector of mainboard ,then measure frequency of CN8 connector(pin No.1 and pin No.2).If the voltage equal to electric supply power and there is stabilized frequency, it means the compressor is broken, change it; If not, change the mainboard. Hisense Refrigerator...
If not , change the freezer fan motor. Pin No. 2 connect 12V power and pin No. 1 connect GND, if the condenser fan motor works normally, change the main-board; If not , change the condenser fan motor. Hisense Refrigerator...
Step 4: Remove the fan motors after removed the three screws (5) holding the fan motors with a Philips screwdriver. 6.5 Light 6.5.1 Basic parameters ● Rated voltage: DC12V 6.5.2 Checking method Check the connecting wiring between light and mainboard is well or not. Repair if it is broken. Hisense Refrigerator...
3. Normally, when the door is closed, the two pins of door switch should be short circuit; When the door is open, the two pins should be open circuit. If the result is not abnormal, change the door switch. If all above is OK ,change the mainboard. ● Hisense Refrigerator...
2. Unplug the connecting terminal, as picture 2. 3. Disassemble the fixed screws, as picture 3. 4. Remove the terminal, as picture 4. 5. Remove the two fixed screws, as picture 5. 6. Take out the display component, as picture 6. Hisense Refrigerator...
6.9 The system of water supplies 6.9.1 The whole system Hisense Refrigerator...
Page 45
7—Water supply inlet cover 8—Icemaker inlet cover 9—Water tube (white, flow into the water tank in fridge room) 10—Water tube (blue, flow into the icemaker in freezer room) 11—Connector (180°) 12— Water tube (white, Motorized valve inlet tube) ● 13—Water valve Hisense Refrigerator...
Page 46
It is necessary to check the wiring or replace the water valve. In the icon flicker process, hold and press“Super Freeze”button+“Super Cool ” button for 3 seconds or power off can end testing. Hisense Refrigerator...
Page 47
6. Remove the white line from buckle of ice tray in the direction of arrow. 7. Peel off the aluminum foil then take the temperature head out. 8. Take the insulation foam out. 9. All parts of the ice maker part show in picture 9. Hisense Refrigerator...
2. Remove the wire connector (2) by pressing the top of them. 3. Disconnect the water line at the check valves (3) and quick connector (4). 7. Cooling system repairing 7.1 Refrigeration system The refrigerator system is Single cooling system: Hisense Refrigerator...
Refrigerant enters dry filter,water and imperity will be filtrated Refrigerant enters Electromagnetism valve, and ● Capillary, then pressure will be reduced Refrigearnt enters finned evaporator and become low temperature low pressure gas after absorbing heat from freezer and refrigerator compartment 7.2 Summary of repair Hisense Refrigerator...