Summary of Contents for Busch-Jaeger 6711 UBT
- Page 1 Product manual │ 15.07.2022 6711 UBT 6711/10 UBT BT relay pill Branding -- Release 2018-01-01...
-
Page 2: Table Of Contents
Table of contents Table of contents Notes on the instruction manual ........................4 Trademarks ..............................4 Safety ................................5 Information and symbols used ......................5 Intended use ............................6 Improper use ............................6 Target group / Qualifications of personnel ..................7 3.4.1 Operation ............................. - Page 3 Table of contents Information about planning and application ....................40 12.1 Mesh network ........................... 40 Fault repair ..............................42 Declaration of conformity ..........................43 Index ................................44 │3 Product manual 2CKA001373B5323...
-
Page 4: Notes On The Instruction Manual
If you pass the device on, also pass on this manual along with it. Busch-Jaeger accepts no liability for any failure to observe the instructions in this manual. If you require additional information or have questions about the device, please contact Busch- Jaeger or visit our Internet site at: www.BUSCH-JAEGER.de... -
Page 5: Safety
However, residual hazards remain. Read and adhere to the safety instructions to prevent hazards of this kind. Busch-Jaeger accepts no liability for any failure to observe the safety instructions. Information and symbols used The following Instructions point to particular hazards involved in the use of the device or provide... -
Page 6: Intended Use
Each use not listed in Chapter 3.2 “Intended use“ on page 6 is deemed improper use and can lead to personal injury and damage to property. Busch-Jaeger is not liable for damages caused by use deemed contrary to the intended use of the device. The associated risk is borne exclusively by the user/operator. -
Page 7: Target Group / Qualifications Of Personnel
Safety Target group / Qualifications of personnel 3.4.1 Operation No special qualifications are needed to operate the device. 3.4.2 Installation, commissioning and maintenance Installation, commissioning and maintenance of the device must only be carried out by trained and properly qualified electrical installers. The electrical installer must have read and understood the manual and follow the instructions provided. -
Page 8: Information On Protection Of The Environment
Information on protection of the environment Information on protection of the environment Environment Consider the protection of the environment! Used electric and electronic devices must not be disposed of with domestic waste. – The device contains valuable raw materials which can be recycled. Therefore, dispose of the device at the appropriate collecting depot. -
Page 9: Product Overview
Product Overview Product Overview Functions This device is a relay insert for decentralized flush-mounted installation. The relay insert is a Bluetooth switch for the lamps listed in section “Types of load“ on page 9. The operation is carried out via one or several radio switches of type 6716 UBT Bluetooth Low Energy Smart Switch and/or via the Casambi app. -
Page 10: Technical Data
Technical data Technical data Technical data Designation Value Nominal voltage 230 V AC ±10%, 50/60 Hz Power 0 to 3000 W Standby power < 0.5 W 13 A (cos φ =1) Maximum breaking capacity Wire cross-section of screw-type terminal: 1.0 - 2.5 mm (rigid and multi-strand) ®... -
Page 11: Connection, Installation / Mounting
Connection, installation / mounting Connection, installation / mounting Requirements for the electrician Danger - Electric voltage! Install the device only if you have the necessary electrical engineering knowledge and experience. ■ Incorrect installation endangers your life and that of the user of the electrical system. -
Page 12: Electrical Connection
Connection, installation / mounting Do not install the device close to electric inducted magnetic fields such as large transformers since this can interfere with the wireless communication. The distance should be at least 1 meter. Electrical connection ‚ L L 1 2 Fig. -
Page 13: Commissioning
Commissioning Commissioning The commissioning of the software is made via the Casambi app. Here the Bluetooth pellet (BT pellet) and the radio switches in the Casambi app are registered in your mobile terminal device and linked with each other. The BT pellet must be put in operation via the software, ■... -
Page 14: Preparation
Commissioning Preparation Initial steps: 1. Permit the Casambi app to activate and use Bluetooth. 2. Permit the Casambi app to access your location. – The specification of the location is only required if you want to use the local daytimes for sunset and sunrise. - Page 15 Commissioning 2. Tap on "Set up new network" [2]. 3. Select an evolution network [3]. – The evolution network is the higher value network. The classic network is not recommended. 4. Assign a name to the network [4]. 5. Activate function "Display lamps in close proximity". –...
-
Page 16: Add Bluetooth Pellet
Commissioning Add Bluetooth pellet Two different types of devices can be integrated in a network in the Casambi app: Bluetooth pellet and radio switch with NFC sensor. In this section you add a BT pellet to a Casambi app. To add a radio switch, see chapter “Add radio switch“ on page 20. Fig. - Page 17 Commissioning – If the coupling status is "Coupled", the device must first be uncoupled from the network, see chapter 8.7 “Uncoupling Bluetooth pellet“ on page 26. Devices that are already coupled cannot be added to any other network. 2. Tip on the information field of the device [3]. 3.
-
Page 18: Renaming The Device
Commissioning Renaming the device In this section the name of a BT pellet is changed. Renaming is not absolutely necessary, yet it is recommended. Meaningful naming makes it easier to allocate the connected devices to specific rooms. Fig. 6: Renaming device To rename a BT pellet, perform the following steps: 1. - Page 19 Commissioning – The characteristics of the device are displayed. 5. Enter a new name [5] in field "Name" [4]. 6. Change to the previous page via the navigation bar [6]. The device with the new name is displayed on the start page of the network [7]. │19 Product manual 2CKA001373B5323...
-
Page 20: Add Radio Switch
Commissioning Add radio switch Adding of radio switches in a Casambi network is performed in two sections: ■ Change into the list of the integrated devices of the desired network. – Here there is an automatic search for updates for all integrated devices. ■... - Page 21 Commissioning Fig 8: Add radio switch 4. Tap on "Switch" [1]. 5. Tap on "Add EnOcean switch" [2]. – The NFC function for the data transmission is activated. 6. Hold the smartphone with the NFC reader close to the radio switch. –...
-
Page 22: Programming The Radio Switch
Commissioning Programming the radio switch The function of each switching position of the radio switch is configured during the programming of the radio switch. Progamming takes place in two sections: ■ Specifying the rocker configuration. ■ Allocate the BT pellet that is to be controlled with the switch position. Fig. - Page 23 Commissioning Fig. 10: Specifying the rocker switch function 3. Scroll down in the device characteristics. 4. Select the default setting of the first rocker [1]. 5. Start the editing of the current rocker function [2]. – The list of the possible functions is displayed. 6.
- Page 24 Commissioning Fig. 11: Rocker functions: Allocation of devices 7. Tap on "Lamp" [1]. – The page "Select lamp" for the allocation of devices is displayed. 8. Select the device that is to be controlled with the rocker [2]. – After the tap, the selected device is displayed highlighted [3]. 9.
- Page 25 Commissioning Notice The Casambi app automatically recognizes the kind of device that is being allocated to the NFC radio switch. ■ If a relay is allocated, a lamp can be switched on or off with a brief actuation of the rocker. ■...
-
Page 26: Uncoupling Bluetooth Pellet
Commissioning Uncoupling Bluetooth pellet During the integration and coupling of BT pellets into the Casambi app it can happen that these devices had already been coupled in a different network, but have not been uncoupled or enabled there. During the coupling and integrating of such a device, the "Coupled" status [2] is correspondingly displayed. - Page 27 Commissioning 3. Tap on "Uncouple device" [4]. 4. Tap on "Start" [5]. – A countdown runs for 5seconds [6]. – The power supply of the BT device must be interrupted once and restored again within these 5 seconds. – The previously coupled BT device is being uncoupled. –...
-
Page 28: Removing Devices
Commissioning Removing devices The BT pellets and NFC radio switches integrated in the Casambi app must be removed from the network in different ways. ■ BT pellets are remove from the network by means of uncoupling. ■ Radio switches cannot take part in communication with mobile terminal devices since they do not have a permanent energy supply. - Page 29 Commissioning – The main page of the network is displayed. 3. Tap on "Editing" [2]. – The integrated devices are marked with a small cross. 4. Tap on the device that is to be removed [3]. – The characteristics of the device are displayed. 5.
- Page 30 Commissioning 1. Tap on "My networks" [1] on the start page. – The list with the created networks opens. 2. Tap on the desired network. – The main page of the network is displayed. 3. Tap on "More" [2]. 4. Tap on "Switch" [3]. –...
-
Page 31: Delete Network
Commissioning Delete network Before a network is deleted, all devices should be removed from there. Otherwise the devices remain in the "Coupled" status and can only be integrated into a different network with great difficulty. – To remove devices, see chapter 8.8 “Removing devices“ on page 28. Fig. -
Page 32: Updating Options
Updating options Updating options The firmware update of the BT pellet is made in the Casambi app. There are two ways for updating the firmware in the Casambi app: ■ Automatic update search during the change into the main page of a network. ■... - Page 33 Updating options Specific update for a device A device update is carried out via the characteristics of the device. Fig. 17: Specific device update Use the following points for the specific installation of updates: 1. Tap on "My networks" [1] on the start page. –...
- Page 34 Updating options 6. Tap on "Update firmware" [4]. The firmware of the device is updated. │34 Product manual 2CKA001373B5323...
-
Page 35: Operation
Operation Operation Operation via radio switch Fig. 18: Operation via radio switch The BT pellet is operated, for example, via the radio switch 6716 UBT Bluetooth Low Energy Smart Switch. The button occupation of the radio switch depends on the configuration of the radio switch. The button occupation of the radio switch is configured in the Casambi app, see chapter 8.6 “Programming the radio switch“... - Page 36 Operation Fig. 20: Casambi app: Main page of the network To operate the devices in a network, perform the following steps: 1. Open the Casambi app on the smartphone or tablet. 2. Tap on "My networks" [1] on the start page. 3.
- Page 37 Operation Dimming a lamp 1. Press the dimmer icon long [1]. – A slider for the dimmer is faded in [3]. 2. Dim the light via the slider or the "Plus" and "Minus" icons. 3. Tap on the screen. – The entry is finished and the slider is faded out.
-
Page 38: Case Studies
The circuit consists of the following devices: ■ Bluetooth Low Energy Smart Switch 6716 UBT ■ BT relay pill 6711 UBT Fig. 22: Example of switch configuration Operation via radio switch: The radio switch with a rocker is programmed to the relay. The relay controls a lamp. -
Page 39: Maintenance
Maintenance Maintenance The device is maintenance-free. In case of damage, e.g. during transport or storage), do not perform repairs. Once the device is opened, the warranty is void. Access to the device must be guaranteed for operation, testing, inspection, maintenance and repairs (according to DIN VDE 0100-520). -
Page 40: Information About Planning And Application
Information about planning and application Information about planning and application 12.1 Mesh network Fig. 23: Mesh network principle [1] Radio switch [2] Interrupted signal path [3] New signal path [4] Actuator/lamp In a mesh network the integrated devices or participants communicate with each other wireless, e.g via Bluetooth or WLAN. - Page 41 Information about planning and application Fig. 24: Example of a mesh network In this example device 4 is to be switched on via the smartphone. However, the distance is to far so that no connection can be established. The switching information is transferred via device 1 to the next available device 2.
-
Page 42: Fault Repair
Fault repair Fault repair The lighting goes out during operation Possible cause: The device to which the lighting is connected has heated up excessively. The thermal fuse has triggered. When the thermal fuse has triggered, a message is displayed in the Casambi app. Action: 1. -
Page 43: Declaration Of Conformity
Declaration of conformity Declaration of conformity Busch-Jaeger herewith declares, that radio system type 6711 UBT conforms to directive 2014/53/EU. The complete text of the EU Declaration of Conformity is available at the following Internet address: 6711 UBT xxxxxxxxxxxxxxxxxxxxxxxxxxxx Table 3: Link to Declaration of Conformity │43... -
Page 44: Index
Index Index Add Bluetooth pellet ............16 Network ................40 Add radio switch ............16, 20 Notes on the instruction manual ..........4 Case studies ................ 38 Operation .................7, 35 Cleaning ................39 Commissioning ..............13 Connection, installation / mounting ........11 Product Overview ..............9 Programming the radio switch ........22, 35 Delete network .............. - Page 45 Busch-Jaeger Elektro GmbH A member of the ABB Group Freisenbergstraße 2 58513 Lüdenscheid www.BUSCH-JAEGER.de info.bje@de.abb.com Central sales service: Tel.: +49 2351 956-1600 Fax: +49 2351 956-1700 © Copyright 2022 Busch-Jaeger Elektro GmbH All rights reserved...