Subscribe to Our Youtube Channel
Related Manuals for DAPAudio EDGE EHS-1
Summary of Contents for DAPAudio EDGE EHS-1
- Page 1 USER MANUAL ENGLISH EDGE EHS-1 Product code: D1475B Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands...
- Page 2 EDGE EHS-1 Preface Thank you for purchasing this DAP product. The purpose of this user manual is to provide instructions for the correct and safe use of this product. Keep the user manual for future reference as it is an integral part of the product. The user manual shall be stored at an easily accessible location.
-
Page 3: Table Of Contents
Installation of the Antennas........................15 Connecting to Power Supply .......................16 Power Linking of Multiple Devices ....................16 Setup Examples ............................17 4 x EDGE EHS-1 ............................17 8 x EDGE EHS-1 ............................18 Connecting the Receiver to Mixer/Amplifier ..................18 Switching ON/OFF – Receiver ......................19 Installation of the Batteries ........................19 Switching ON/OFF –... - Page 4 EDGE EHS-1 Main Menu Options ..........................30 Group ..............................31 Channel ...............................31 Frequency ............................31 Gain ..............................32 RF Output Power ..........................32 Lock ...............................33 Channel and Frequency Overview ......................34 Troubleshooting ..............................35 Adjusting the Microphone Gain ........................35 Maintenance ..............................36 Preventive Maintenance ..........................36 Basic Cleaning Instructions ........................36 Corrective Maintenance ..........................36...
-
Page 5: Introduction
After unpacking, check the contents of the box. If any parts are missing or damaged, contact your Highlite International dealer. Your shipment includes: ● DAP EDGE EHS-1 (receiver + transmitter) ● 2 x antenna ● AC power adapter (1,4 m) ●... -
Page 6: Symbols And Signal Words
EDGE EHS-1 Symbols and Signal Words Safety notes and warnings are indicated throughout the user manual by safety signs. Always follow the instructions provided in this user manual. Indicates an imminently hazardous situation which, if not avoided, will result in DANGER death or serious injury. -
Page 7: Safety
EDGE EHS-1 Safety Important Read and follow the instructions in this user manual before installing, operating or servicing this product. The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual. Warnings and Safety Instructions... -
Page 8: Requirements For The User
EDGE EHS-1 Attention This device shall be used only for the purposes it is designed for. This device is designed to be used as a wireless microphone system. Any incorrect use may lead to hazardous situations and result in injuries and material damage. -
Page 9: Description Of The Device
Description of the Device The EDGE EHS-1 is a wireless handheld system. The set consists of a handheld transmitter and a receiver. The EDGE is suitable for voice transmission. The transmitter is powered by 2 x AA LR6 (alkaline) batteries (not included). -
Page 10: Microphone (Handheld Transmitter)
EDGE EHS-1 Microphone (Handheld Transmitter) Fig. 04 Microphone head IR sensor OLED display Transmitter antenna Power button (on/off) Battery housing (2 x AA LR6) Battery cover SET button 20) DOWN button 25) UP button Product code: D1475B... -
Page 11: Product Specifications
EDGE EHS-1 Product Specifications Model: EDGE EHS-1 Receiver Electrical: Input voltage: 100–240 V AC, 50/60 Hz Output voltage: 12–15 V DC Power consumption: 5,3 W AC power adapter: Input voltage: 100–240 V AC, 50/60 Hz Output voltage: 15 V DC... -
Page 12: Optional Accessories
EDGE EHS-1 Gain range: 30 dB Polar pattern: Cardioid Frequency response: 60–18000 Hz Maximum SPL: 130 dB Frequency range: 610–668 MHz Wireless stability: 0,0015 % RF power: 30 mW RF bandwidth: 60 MHz Frequency deviation: ± 75 kHz Spurious rejection: ≤... -
Page 13: Dimensions
EDGE EHS-1 Dimensions Fig. 05 Product code: D1475B... -
Page 14: Installation And Setup
EDGE EHS-1 Installation and Setup Ambient Conditions ● The device can be used only indoors. ● The maximum ambient temperature t = 50 °C must never be exceeded. ● The relative humidity must not exceed 50 % with an ambient temperature of 50 °C. -
Page 15: Two Receivers
EDGE EHS-1 Two Receivers Attach the supplied short mounting brackets with the mounting screws to the receivers. Use a Phillips screwdriver to tighten the mounting screws. Fig. 07 Attach the supplied mounting plate with the mounting screws to the bottom of both receivers. Use a Phillips screwdriver to tighten the mounting screws. -
Page 16: Setup
EDGE EHS-1 Setup Attention Connect all data cables before supplying power. Disconnect power supply before connecting or disconnecting data cables. To set up the wireless handheld system, follow the steps below: Install the antennas. See 4.3.1. Installation of the Antennas on page 15. -
Page 17: Connecting To Power Supply
EDGE EHS-1 Connecting to Power Supply Attention Incorrect handling of the AC power adapter may result in hazardous situations This device is delivered with an AC power adapter. Incorrect handling of the AC power adapter may result in hazardous situations. -
Page 18: Setup Examples
It is possible to connect multiple receivers and transmitters and to install accessories. See 3.5. Optional Accessories on page 11 for more information. 4 x EDGE EHS-1 In a setup with 4 receivers, you can use a single antenna distributor and 1 set of unidirectional/omnidirectional antennas. -
Page 19: Edge Ehs-1
EDGE EHS-1 8 x EDGE EHS-1 In a setup with 8 receivers, you can use 2 antenna distributors and 1 set of unidirectional/omnidirectional antennas. The antennas receive the signal from the transmitter(s) and send it to the antenna distributor. The antenna distributor sends the signal to the other connected antenna distributor. -
Page 20: Switching On/Off - Receiver
EDGE EHS-1 Switching ON/OFF – Receiver The receiver has a power button. ● Press and hold down the power button (05) for 2 seconds to switch on the receiver. The LCD display (01) lights up. ● Press and hold down the power button (05) for 2 seconds to switch off the receiver. The receiver remains energized. -
Page 21: Switching On/Off - Transmitter
EDGE EHS-1 Switching ON/OFF – Transmitter The transmitter has a power button. ● Press and hold down the power button (18) for 3 seconds to switch the transmitter on/off. ● When in the main menu of the transmitter, press the power button (18) to confirm selections and to return to the start screen. -
Page 22: Operation
EDGE EHS-1 Operation To operate the device, talk or sing into the transmitter. The AF signal strength (L) indicator on the LCD display (01) increases or decreases during talking/singing. If the signal is too loud, “AF” and “P” of the AF signal strength (L) indicator flash red. -
Page 23: Main Menu Options
EDGE EHS-1 Main Menu Options Upon start-up, the display shows the DAP logo. After 2 seconds, the display shows the current status of the receiver. Press the control (02) to open the main menu. The display shows: Turn the control (02) to toggle through the following 14 options: ●... -
Page 24: Group
EDGE EHS-1 Group In this menu you can select a group. Each group (A–J) has a unique set of channels with 14 fixed frequencies per channel. See 5.5. Channel and Frequency Overview on page 34. Turn the control (02) to select GROUP. -
Page 25: Scan
EDGE EHS-1 Scan In this menu you can automatically scan the entire frequency range, to find the unused frequencies and avoid interference. Turn the control (02) to select SCAN. Press the control (02) to scan the entire frequency range (610–668 MHz). This process may take up to 2 minutes. -
Page 26: Lock
EDGE EHS-1 Lock In this menu you can lock the display of the receiver. Turn the control (02) to select LOCK. Press the control (02) to edit. Turn the control (02) to select one of the 2 options: ● ON: The display is locked ●... -
Page 27: Receiver Gain
EDGE EHS-1 Receiver Gain In this menu you can set the output gain of the receiver. Turn the control (02) to select RX GAIN. Press the control (02) to edit. Turn the control (02) to set the output gain. The adjustment range is from -32 dB to +4 dB. -
Page 28: Squelch
EDGE EHS-1 Squelch In this menu you can set the squelch threshold. The squelch threshold is pre-set at the factory and normally needs no further adjustment. In case the receiver picks up other signals besides the signal of the transmitter, follow the steps bellow. To eliminate the interference, increase the squelch threshold for the respective channel. -
Page 29: Color
EDGE EHS-1 Color In this menu you can assign a color to the transmitter. It is useful when working with multiple receivers and transmitters. Put a sticker with the correct color on your transmitter. The stickers are supplied with the device. -
Page 30: Antenna Power Supply
EDGE EHS-1 Antenna Power Supply In this menu you can set the antenna input/output power supply. Turn the control (02) to select ANT DC. Press the control (02) to edit. Turn the control (02) to select ON or OFF. Press the control (02) to confirm. -
Page 31: Control Panel - Transmitter
EDGE EHS-1 Control Panel – Transmitter N) Transmitter battery status O) Frequency P) Group (A–J) and channel (1–14) Q) Transmitter lock R) Gain level Fig. 14 ● Press the SET button (24) to open a menu and to confirm a selection. -
Page 32: Group
EDGE EHS-1 Group In this menu you can select a group. Each group (A–J) has a unique set of channels with 14 fixed frequencies per channel. See 5.5. Channel and Frequency Overview on page 34. Press the UP/DOWN buttons (25/20) to select GROUP. -
Page 33: Gain
EDGE EHS-1 Gain In this menu you can set the gain of the transmitter. Press the UP/DOWN buttons (25/20) to select GAIN. Press the SET button (24) to edit. Press the UP/DOWN buttons (25/20) to set the desired gain. The adjustment range is from -32 dB to +4 dB. -
Page 34: Lock
EDGE EHS-1 Lock In this menu you can lock the display of the transmitter. Press the UP/DOWN buttons (25/20) to select LOCK. Press the SET button (24) to edit. Press the UP/DOWN buttons (25/20) to select one of the 2 options: ●... -
Page 35: Channel And Frequency Overview
EDGE EHS-1 Channel and Frequency Overview The carrier frequency is in the range 610–668 MHz. Frequency Frequency Frequency Frequency Frequency 610.000 MHz 610.250 MHz 610.500 MHz 610.750 MHz 611.000 MHz 612.025 MHz 612.275 MHz 612.525 MHz 612.775 MHz 613.025 MHz 614.250 MHz... -
Page 36: Troubleshooting
EDGE EHS-1 Troubleshooting This troubleshooting guide contains solutions to problems which can be carried out by an ordinary person. The device does not contain user-serviceable parts. Unauthorized modifications to the device will render the warranty void. Such modifications may result in injuries and material damage. -
Page 37: Maintenance
EDGE EHS-1 Maintenance Preventive Maintenance Attention Before use, examine the device visually for any defects. Make sure that: ● All screws used for installing the device or parts of the device are tightly fastened and are not corroded. ● There are no deformations on housings, fixations and installation points. -
Page 38: Disposal
Approval Hereby, Highlite International declares that the device EDGE EHS-1, product code D1475B, is in compliance with Directive 2014/53/EU (RED – Radio Equipment Directive). The full text of the EU declaration of conformity is available at the respective product page on the website of Highlite International (www.highlite.com). - Page 39 EDGE EHS-1 Product code: D1475B...
- Page 40 ©2023 DAP...
Need help?
Do you have a question about the EDGE EHS-1 and is the answer not in the manual?
Questions and answers