Related Manuals for DAPAudio COM-42
Summary of Contents for DAPAudio COM-42
- Page 1 USER MANUAL ENGLISH COM-42 2Ch Handheld set Product code: D1464 Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands...
- Page 2 COM-42 2Ch Handheld set Preface Thank you for purchasing this DAP product. The purpose of this user manual is to provide instructions for the correct and safe use of this product. Keep the user manual for future reference as it is an integral part of the product. The user manual shall be stored at an easily accessible location.
-
Page 3: Table Of Contents
COM-42 2Ch Handheld set Table of contents Introduction ................................3 Before Using the Product ..........................3 Intended Use ............................... 3 Product Lifespan ..............................3 Text Conventions ..............................3 Symbols and Signal Words ..........................4 Symbols on the Information Label ........................4 Safety .................................. -
Page 4: Introduction
COM-42 2Ch Handheld set Introduction Before Using the Product Important Read and follow the instructions in this user manual before installing, operating or servicing this product. The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual. -
Page 5: Symbols And Signal Words
COM-42 2Ch Handheld set Symbols and Signal Words Safety notes and warnings are indicated throughout the user manual by safety signs. Always follow the instructions provided in this user manual. Indicates an imminently hazardous situation which, if not avoided, will result in DANGER death or serious injury. -
Page 6: Safety
COM-42 2Ch Handheld set Safety Important Read and follow the instructions in this user manual before installing, operating or servicing this product. The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual. Warnings and Safety Instructions... -
Page 7: Requirements For The User
COM-42 2Ch Handheld set Attention This device shall be used only for the purposes it is designed for. This device is designed to be used as a wireless microphone system. Any incorrect use may lead to hazardous situations and result in injuries and material damage. -
Page 8: Description Of The Device
COM-42 2Ch Handheld set Description of the Device The DAP COM-42 2Ch Handheld set is a wireless microphone system consisting of a wireless receiver and 2 handheld wireless transmitters. The wireless receiver is equipped with 2 balanced XLR outputs and an unbalanced ¼”... -
Page 9: Handheld Transmitter (Microphone)
COM-42 2Ch Handheld set Handheld Transmitter (Microphone) Fig. 04 18) Mute LED indicator Microphone body 19) ON/OFF button Battery compartment lock 20) Gain control Battery compartment 21) IR sensor (transmitter) Battery compartment cover 22) Plastic mini screwdriver 23) Microphone housing... -
Page 10: Product Specifications
COM-42 2Ch Handheld set Product Specifications Model: COM-42 2Ch Handheld set Receiver Electrical: Input voltage: 15 V DC Input current: 0,3 A Power consumption: 15 W Physical: Dimensions: 210 x 210 x 45 mm (L x W x H) Installation depth:... -
Page 11: Optional Accessories
The receiver can be mounted in a 19-inch rack. The device is delivered without a rack mount kit. The rack mount kit can be purchased separately. Contact your Highlite International dealer for more information. Product code: D1466 (Rackmount for 1 pc COM-42) Product code: D1464... -
Page 12: Dimensions
COM-42 2Ch Handheld set Dimensions Fig. 05 Fig. 06 Fig. 07 Product code: D1464... -
Page 13: Installation And Setup
COM-42 2Ch Handheld set Installation and Setup Ambient Conditions ● The device can be used only indoors. ● The maximum ambient temperature t = 40 °C must never be exceeded. ● The relative humidity must not exceed 50 % with an ambient temperature of 40 °C. -
Page 14: Transmitter Setup
COM-42 2Ch Handheld set Transmitter Setup Installation of the Batteries The microphone is delivered without batteries. It accepts 2 LR6 (alkaline) AA batteries. To install the batteries: 01) Turn the microphone housing (23) counterclockwise and remove it from the microphone body (24). -
Page 15: Pairing
COM-42 2Ch Handheld set Pairing The receiver can be paired with two transmitters: one transmitter on channel A (CH A) and the other transmitter on channel B (CH B). The receiver and the transmitters must be set to the same channel. -
Page 16: Connecting The Receiver To Mixer/Amplifier
COM-42 2Ch Handheld set Connecting the Receiver to Mixer/Amplifier Attention Connect all data cables before supplying power. Disconnect power supply before connecting or disconnecting data cables. The receiver has 2 balanced XLR output connectors and 1 unbalanced ¼ ʺ TRS jack output connector. -
Page 17: Operation
COM-42 2Ch Handheld set Operation Attention This device must be used only for the purposes it is designed for. This device is intended for use as a wireless microphone system. It is not suitable for households. Any other use, not mentioned under intended use, is regarded as non-intended and incorrect use. -
Page 18: Operation
COM-42 2Ch Handheld set Operation To operate the wireless microphone system: 01) Complete the installation of the receiver. See 4.2.1. Mounting on page 12 and 4.2.2. Installation of the Antennas on page 12. 02) Complete the setup of the transmitter(s). See 4.3. Transmitter Setup on page 13. -
Page 19: Channels Overview
COM-42 2Ch Handheld set Channels Overview The carrier frequency is in the range 606–630 MHz. Frequency (MHz) Frequency (MHz) Frequency (MHz) Frequency (MHz) 606.125 611.750 617.375 623.000 606.350 611.975 617.600 623.225 606.575 612.200 617.825 623.450 606.800 612.425 618.050 623.675 607.025 612.650... -
Page 20: Troubleshooting
COM-42 2Ch Handheld set Troubleshooting This troubleshooting guide contains solutions to problems which can be carried out by an ordinary person. The device does not contain user-serviceable parts. Unauthorized modifications to the device will render the warranty void. Such modifications may result in injuries and material damage. -
Page 21: Adjusting The Microphone Gain
COM-42 2Ch Handheld set Adjusting the Microphone Gain To adjust the microphone gain: 01) Turn the microphone housing (23) counterclockwise and remove it from the microphone body (24). See Fig. 08 on page 13. 02) Remove the plastic mini screwdriver (22) from the transmitter. -
Page 22: Maintenance
COM-42 2Ch Handheld set Maintenance Preventive Maintenance Attention Before use, examine the device visually for any defects. Make sure that: ● All screws used for installing the device or parts of the device are tightly fastened and are not corroded. -
Page 23: Deinstallation, Transportation And Storage
COM-42 2Ch Handheld set Deinstallation, Transportation and Storage ● Disconnect power supply before deinstallation. ● Use the original packaging to transport the device, if possible. ● Clean the device before storing. Follow the cleaning instructions in chapter 7.1.1. Basic Cleaning Instructions on page 21. - Page 24 ©2023 DAP...
Need help?
Do you have a question about the COM-42 and is the answer not in the manual?
Questions and answers