Table of Contents
Advertisement
• The security disable mode is maintained until the main power is
turned off (by setting the main power switch to "O" or unplugging
the power cord). In the following cases you will be asked to check
the protect key or input the keyword:
(1)
When "OK" is selected at an image for which security is set
and the power is turned off then back on
(2)
When the main power is turned off then back on while the
security function is enabled
(3)
When you attempt to display an image for which security is
set while the security function is enabled
• Blanks (spaces) cannot be used in the Keyword section.
To delete PC card data you registered.
1. Use the SELECT
button to select "Delete" and use the SELECT
button to select the list window.
2. Use the SELECT
button to select the PC card data you wish to
delete.
3. Press the SELECT
button to select "Delete" and press the ENTER
button.
The PC card data will be deleted.
If you've lost your registered PC card, proceed as follows:
NOTE: NEC or your dealer will provide you with your Release Code in exchange
for your registered keyword and Request Code. See more information at the end
of this section.
1. Press and hold the POWER button for a minimum of two seconds.
The projector will be turned on and display a message to the effect
that the projector is security-protected.
2. Select [Setup]
[Page 3]
ENTER button.
The Release Code input screen will be displayed as well as your
Request Code (24 alphanumeric characters).
3. Enter your Release Code in the Release Code Input screen.
The projector will turn on.
* If the projector is turned on by entering the Release Code, your Se-
curity will be disabled.
NOTE:
* Some types of PC cards cannot be registered as your protect key.
* It is recommended that you register two or more PC cards in case you lose or
damage your registered PC card.
* Formatting your registered PC card will disable your protect key function.
NOTE:
For additional information visit:
US : http://www.necvisualsystems.com
Europe : http://www.nec-europe.com/
Global : http://www.nec-pj.com/
[Security] from the menu and press the
Information
Displays the status of the current signal, and the lamp and the projector
usage hours. This dialog box has four pages.
The information included are as follows:
[Page 1]
Source Name
Input Terminal
Entry No.
Horizontal Frequency
Vertical Frequency
[Page 2]
Signal Type
Video Type
Sync Type
Interlace
Sync Polarity
[Page 3]
Remaining Lamp Time (%)
Lamp Hour Meter (H)
Projector Usage (H)
[Page 4]
Version (BIOS, Firmware, Data)
NOTE: The progress indicator shows the percentage of remaining bulb life. The
value informs you of the amount of lamp and projector usage respectively.
Remaining Lamp Time Display
When the remaining lamp time reaches 0, the Remaining Lamp Time
bar indicator changes from 0% to 100 Hours and starts counting down.
If the remaining lamp time reaches 0 hours, the projector will not turn on
regardless of whether the lamp mode is set to Normal or Eco.
Returning to Factory Default [Reset]
The Factory Default feature allows you to change adjustments and set-
ting to the factory preset for source except the following:
Current Signal:
Resets the adjustments for the current signal to the factory preset
levels.
All the items in "Volume", "Image (except Image Position)" and "Pic-
ture" can be reset.
All Data:
Reset all the adjustments and settings for all the signals to the fac-
tory preset except Remaining Lamp Time, Lamp Hour Meter, Projec-
tor Usage, Language, Background, Entry List, Standby Mode, LAN
Mode, Security and Password (Logo).
(To reset the lamp usage time, see "Clearing Lamp Hour Meter" on
page E-33)
All Data (Including Entry List):
Also deletes all the signals in the Entry List and returns to the factory
preset.
E-37
Advertisement
Table of Contents
