NEC MultiSync V461 User Manual

NEC MultiSync V461 User Manual

Nec v461: user guide
Hide thumbs Also See for MultiSync V461:

Advertisement

User's Manual
MultiSync V321
MultiSync V421
MultiSync V461

Advertisement

Table of Contents
loading

Summary of Contents for NEC MultiSync V461

  • Page 1 User’s Manual MultiSync V321 MultiSync V421 MultiSync V461...
  • Page 2: Table Of Contents

    Controlling the LCD monitor via LAN Control ... English-25 Features ... English-28 Troubleshooting ... English-29 Specifications - V321 ... English-30 Specifications - V421 ... English-31 Specifications - V461 ... English-32 Pin Assignment ... English-33 Manufacturer’s Recycling and Energy Information ... English-34 www.necdisplaysolutions.com...
  • Page 3: Important Information

    Voltage 120* *When operating the MultiSync LCD monitor with its AC 125-240V power supply, use a power supply cord that matches the power supply voltage of the AC power outlet being used. NOTE: This product can only be serviced in the country where it was purchased.
  • Page 4: Canadian Department Of Communications Compliance Statement

    C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No. 60950-1. FCC Information 1. Use the attached specified cables with the MultiSync V321 (L329N8)/MultiSync V421 (L429N9)/MultiSync V461 (L469NA) color monitor so as not to interfere with radio and television reception.
  • Page 5: Safety Precautions, Maintenance & Recommended Use

    Do not use monitor in high temperature, humid, dusty, or oily areas. • If monitor or glass is broken, do not come in contact with the liquid crystal and handle with care. • Allow adequate ventilation around the monitor, so that heat can properly dissipate.
  • Page 6: Contents

    CD-ROM Type and number of power cords included will depend on the where the LCD monitor is to be shipped. When more than one power cord is included, please use a power cord that matches the AC voltage of the power outlet and has been approved by and complies with the safety standard of your particular country.
  • Page 7: Installation

    Please note the following when mounting on wall or ceiling • When using mounting accessories other than those that are NEC approved, they must comply with the VESA- compatible (FDMlv1) mounting method. Unit • NEC strongly recommends using size M6 screws...
  • Page 8: Attaching Mounting Accessories

    Table NOTE: ST-3215 is for V321. Use the Thumbscrews included with ST-3215. ST-4020 is for V421 and V461. (V421 and V461 are not mentioned in ST-4020 manual). Before using optional table top stand, remove installed thumbscrews from the display first.
  • Page 9 When using the display with the Tabletop Stand fasten the LCD to a wall using a cord or chain that can support the weight of the monitor in order to prevent the monitor from falling. Fasten the cord or chain to the monitor using the provided clamp and screw.
  • Page 10: Parts Name And Functions

    Glows green when the LCD monitor is in active mode. Glows red when the LCD is in POWER OFF mode. When the LCD monitor is in POWER SAVE mode, it will glow both green and red. When SCHEDULE is enabled, it will blink green and glow red.
  • Page 11: Terminal Panel

    To output the audio signal from AUDIO 1, 2, 3. Note: This speaker terminal is for optional speaker. SP-3215 for MultiSync V321, SP-P4046 for MultiSync V421, SP-4615 for MultiSync V461. When you use SP-P4046 for V421, please use SP-P4046 with large extension blocks (included in speaker), as if being mounted on P461.
  • Page 12: Wireless Remote Control

    Wireless Remote Control POWER button Switches the power on/off. INPUT button Shows Input select menu for [DVI], [VGA], [RGB/HV], [HDMI], [DVD/HD], [S-VIDEO], [VIDEO1], [VIDEO2]. AUDIO INPUT button Selects audio input source [AUDIO:1], [AUDIO:2], [AUDIO:3]. SIZE button Selects picture size, [FULL], [NORMAL], [CUSTOM], [DYNAMIC] and [REAL].
  • Page 13: Operating Range For The Remote Control

    Operating Range for the Remote Control Point the top of the remote control toward the LCD monitor’s remote sensor during button operation. Use the remote control within a distance of about 7 m (23 ft.) from the front of the LCD monitor’s remote control sensor or at a horizontal and vertical angle of within 30°...
  • Page 14: Setup

    C. Replace the cover. CAUTION: Incorrect usage of batteries can result in leaks or bursting. NEC recommends the following battery use: • Place “AAA” size batteries matching the (+) and (-) signs on each battery to the (+) and (-) signs of the battery compartment.
  • Page 15 5. Switch on the power of all the attached external equipment When connected with a computer, switch on the power of the computer first. 6. Operate the attached external equipment Display the signal from the desired input source. 7. Adjust the sound Make volume adjustments when required.
  • Page 16: Connections

    Connections NOTE: Do not connect/disconnect cables when turning on the monitor or other external equipment as this may result in a loss of the monitor image. NOTE: Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor turns down the sound.
  • Page 17: Connecting A Personal Computer

    Connecting a Personal Computer Connecting your computer to your LCD monitor will enable you to display your computer’s screen image. Some video cards with a pixel clock over 165 MHz may not display an image correctly. Your LCD monitor displays proper image by adjusting the factory preset timing signal automatically.
  • Page 18: Basic Operation

    The LCD monitor power indicator will turn green while powered on and will turn red while powered off. NOTE: The Main Power Switch must be in the ON position in order to power up the monitor using the remote control or the Power Button on the front of the LCD.
  • Page 19: Power Indicator

    Diagnosis (Detecting failure) Red Blinking * See troubleshooting on page 29 Using Power Management The LCD monitor follows the VESA approved DPM Power Management function. The power management function is an energy saving function that automatically reduces the power consumption of the display when the keyboard or the mouse has not been used for a fixed period.
  • Page 20: Osd (On-Screen-Display) Controls

    OSD (On-Screen-Display) Controls Remote Control Press “+”, “-” button to Press MENU button to select Main menu, and open Main menu. press Up, Down button to enter Sub menu. Control Panel Press EXIT button to open Main menu and press “+”, “-” button to select Main menu.
  • Page 21: Picture

    Setting PICTURE BRIGHTNESS Adjusts the overall image and background brightness. CONTRAST Adjusts the image brightness in relation to the input signal. NOTE: sRGB picture mode is standard and cannot be changed. SHARPNESS Adjusts the crispness of the image. BLACK LEVEL Adjusts the image brightness in relation to the background.
  • Page 22: Audio

    Resets the all settings within the AUDIO menu back to factory setting. SCHEDULE OFF TIMER Sets the monitor to power off after a length of time. A time between 1 to 24 hours is available. SCHEDULE Creates a working schedule for the monitor to use.
  • Page 23: Multi Display

    Note: When connecting DVI, video card might not stop sending digital data even if image has disappeared. In this case the monitor does not get to power management mode. Selecting “ON”, the monitor will go to power management mode when DVI, VGA, RGB/HV sync is lost. VIDEO Selecting “ON”, the monitor will go to power management mode after about 10 minutes when DVD/HD and...
  • Page 24: Advanced Option

    SIDE BORDER COLOR Adjusts the color of the side borders when a 4:3 image is displayed. Press + button, the bar will become lighter. Press - button, the bar will become darker. DISPLAY PROTECTION Resets the all settings within the DISPLAY PROTECTION menu back to factory setting. RESET ADVANCED OPTION INPUT CHANGE...
  • Page 25 ON time should be earlier than OFF time. If OFF time is earlier than ON time, schedule function is not working properly. If you would like to set the monitor power on at 23:00 and power off at 6:00 next morning, you should set 2 settings. First setting is ON time is “23:00”...
  • Page 26: Controlling The Lcd Monitor Via Rs-232C Remote Control

    NOTE: If your PC is equipped only with a 25-pin serial port connector, a 25-pin serial port adapter is required. Contact your dealer for details. * In order to function, the RS-232C OUT terminal can only be connected to another monitor of the same model. Do not connect to other types of equipment.
  • Page 27: Controlling The Lcd Monitor Via Lan Control

    To perform the monitor control from a web browser, you must have an exclusive application installed on your computer. The IP address and subnet mask of the monitor can be set on the Network Setting screen of the web browser by using an HTTP server function.
  • Page 28: Network Settings

    Regarding the actual address that is entered for the address or entered into the URL column when operation of the monitor is via a browser, the host name can be used as it is when the host name corresponding to the IP address of the monitor has been registered to the domain name server by a network administrator, or the host name corresponding to the IP address of the monitor has been set in the “HOSTS”...
  • Page 29 Type in the hostname of the network connected to the monitor. Up to 60 alphanumeric characters can be used. DOMAIN NAME Type in the domain name of the network connected to the monitor. Up to 60 alphanumeric characters can be used. ALERT MAIL Checking [ENABLE] will turn on the Alert Mail feature.
  • Page 30: Features

    VESA Standard (FDMIv1) Mounting Interface: Allows users to connect their LCD monitor to any VESA standard (FDMIv1) third party mounting arm or bracket. Allows for the monitor to be mounted on a wall or an arm using any third party compliant device.
  • Page 31: Troubleshooting

    NOTE: As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use.
  • Page 32: Specifications - V321

    Specifications - V321 Product Specifications LCD Module Design View Distance: Frequency Pixel Clock Viewable Size Input Signal DVI-D 24pin Digital RGB 15pin Mini D-sub Analog RGB Sync RGB/HV* BNC (R,G,B,H,V) Analog RGB Sync HDMI HDMI Connector Digital RGB DVD/HD* BNC (Y, Cb/Pb, Cr/Pr) Component S-VIDEO Mini DIN 4 pin...
  • Page 33: Specifications - V421

    Specifications - V421 Product Specifications LCD Module Pixel Pitch: Resolution: Brightness: Contrast Ratio: Viewing Angle: Design View Distance: Frequency Horizontal: Pixel Clock Viewable Size Input Signal DVI-D 24pin Digital RGB 15pin Mini D-sub Analog RGB Sync RGB/HV* BNC (R,G,B,H,V) Analog RGB Sync HDMI HDMI Connector...
  • Page 34: Specifications - V461

    Specifications - V461 Product Specifications LCD Module Design View Distance: Frequency Pixel Clock Viewable Size Input Signal DVI-D 24pin Digital RGB 15pin Mini D-sub Analog RGB Sync RGB/HV* BNC (R,G,B,H,V) Analog RGB Sync HDMI HDMI Connector Digital RGB DVD/HD* BNC (Y, Cb/Pb, Cr/Pr)
  • Page 35: Pin Assignment

    Pin Assignment RS-232C input Pin No Name connected to 7&8 connected to 6 connected to 4 connected to 1&8 connected to 1&7 This LCD monitor uses RXD, TXD and GND lines for RS-232C control. D-SUB 9P English-33...
  • Page 36: Manufacturer's Recycling And Energy Information

    Manufacturer’s Recycling and Energy Information NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally- friendly products, and always strive to help define and comply with the latest independent standards from agencies such as ISO (International Organisation for Standardization) and TCO (Swedish Trades Union).

Table of Contents