Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for SVS-Vistek CoaxPress EoSens Creation 1.1CXP2
Summary of Contents for SVS-Vistek CoaxPress EoSens Creation 1.1CXP2
- Page 1 EoSens® Creation 1.1CXP2 User Guide...
-
Page 2: Table Of Contents
Contents Before you start About this manual 1.1.1 Tips, remarks, and notes 1.1.2 Registered trademarks 1.1.3 Conformity and use 1.1.4 Supplements Warranty and non-warranty clause Support Introduction Intended use Scope of delivery Optional accessories System requirements The camera Camera description Operating temperature Additional cooling Interfaces of the camera... - Page 3 Camera dimensions 5.4.1 Camera dimensions (fanless) 5.4.2 Camera dimensions (with fan) Spectral response 5.5.1 Monochrome and color Appendix Declaration of Conformity...
- Page 4 Figures Fig.: 3-1: Interfaces of the camera EoSens® Creation 1.1CXP2 Fig.: 4-1: Connecting input and output signals with the internal circuit Fig.: 4-2: IO signals Fig.: 4-3: Connecting the camera and image processing system Fig.: 5-1: Rear view (fanless) Fig.: 5-2: Side view (fanless) with C-mount adapter Fig.: 5-3: Side view (fanless) with F-mount adapter Fig.: 5-4: Side view (fanless) with G-mount adapter Fig.: 5-5: Rear view (with fan)
-
Page 5: Before You Start
Before you start About this manual This manual contains helpful information to install and operate the described cam- era. It has been produced with care. Nevertheless, information might be erroneous or incomplete. Mikrotron GmbH cannot be held responsible for any problems resulting from incomplete or erroneous information. -
Page 6: Supplements
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions given in this guide, may cause harmful interference to radio communications. Operation of this equipment in a res- idential area is likely to cause harmful interference in which case the user will have to correct the interference at its own expense. -
Page 7: Warranty And Non-Warranty Clause
Life support applications The products described in this manual are not designed for use in life support appli- ances or devices and systems where malfunction of these products can reasonably be expected to result in personal injury. NOTICE Mikrotron customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Mikrotron for any damages res- ulting from such improper use or sale. -
Page 8: Introduction
Introduction Intended use The camera EoSens® Creation 1.1CXP2 belongs to the product class of so-called high-speed machine vision (MV) cameras that are integrated into test or meas- urement systems. High-speed MV cameras are designed to capture images with high frame rate for various purposes in an industrial or scientific environment to deliver image data for further analysis. -
Page 9: System Requirements
We recommend the following cable: KKRDRG59UBNCUBNC05/12GX1 (12GHz µBNC RG59) - 5m Power supply If you do not use power over CXP, you need an external power supply unit, e.g.: NTCAM132X (12 V/2.5 A) with 12 pin Hirose connector (HR10A-10P-12S(73) and 5 m cable NTCAM132XIO (12 V/2.5 A) with 12 pin Hirose connector (HR10A-10P-12S (73) and 5 m cable plus additional strobe out line System requirements... -
Page 10: The Camera
The camera Camera description All cameras of the EoSens CXP family are CoaXPress compliant. The high-speed CMOS cameras come with a 1.1 Megapixel sensor of 1280 x 864 (H x V). They are widely configurable and scalable to fit your needs and are available in monochrome and color (Bayer filter). -
Page 11: Operating Temperature
Operating temperature If the camera is mounted on mechanical parts, the heat generated during operation will be dissipated by the optionally attached fan, the cooling fins at the rear of the camera, and the mechanical parts. NOTICE The camera body temperature must not exceed the values specified in the technical data (see "Technical data"... -
Page 12: Interfaces Of The Camera
Interfaces of the camera Fig.: 3-1: Interfaces of the camera EoSens® Creation 1.1CXP2 1 Status LED to verify the operating status of the camera 2 Four CoaXPress µBNC connectors to connect the camera with a CoaXPress compliant frame grabber. The ∆- marked line can supply the camera with power via power over coax (PoC). -
Page 13: Status Led
Status LED The multi-color status LED indicates camera and connection states. LED State Indication No power Solid orange System is booting Slow pulse red Powered, but nothing connected (not applicable if PoC is used) Fast flash alternate Connection detection in progress, PoC active green/orange Fast flash orange Connection detection in progress, PoC not in use... -
Page 14: First Steps
First steps Connecting a frame grabber The transmission speed of the camera can either be set to 3.125, 6.25, or 12.5 Gb/s. The possible cable length depends on the cable type used, its quality, and the selected transmission speed. The following table provides examples. These values will only be reached if the signal quality meets the requirements of the CXP2.0 spe- cification. -
Page 15: Connecting An External Power Supply Or I/O Signals
The possible connector combinations are shown in the table below. No. of con- Connector combination nections 2 1+2 (link) 4 1+2+3+4 (link) INFO All connections are hot-pluggable. Connecting an external power supply or I/O signals If you prefer an external 12 - 24V DC power supply (min. 18 W), connect it with the 12-pin connector at the rear of the camera. -
Page 16: Fig.: 4-1: Connecting Input And Output Signals With The Internal Circuit
Internally connected with: pin 4 pin 8 pin 6 pin 10 connected with pin 3 + 5 Fig.: 4-1: Connecting input and output signals with the internal circuit All inputs accept 3.3 V LVTTL signals. They are also 5 V TTL compatible. All inputs can also accept signals with 12 ... -
Page 17: Connecting Camera And Image Processing System
Connecting camera and image processing system NOTICE To make use of the full performance, all cables, connectors and the frame grabber must be CoaXPress V2.0 compliant. INFO If a CXP V1.1 frame grabber is used, only speeds up to CXP-6 (6.25 Gb/s) can be achieved. -
Page 18: Cleaning Sensor And Lens
INFO The camera has NOT to be configured by the host to start operation. The power-up profile will deliver all necessary values. Serial number and firmware version are provided in the non-volatile memory of the camera. Use the GenICam feature “DeviceSerialNumber” to read the serial number and the firmware revision. - Page 19 1. Open the tool “CXP Updater.exe” in the folder “Firmware”. 2. Select the CTI file that corresponds to the frame grabber board. If unsure, con- sult the Device Manager. 3. To add a CTI file that is not in the list, select Add another CTI file and navigate to the file.
-
Page 20: Technical Data
Technical data Camera specifications Frame rate (8 bit) max. 3674 fps Pixel depth 8 /10 bit Shutter speed 2 µs – 1 s Shutter time (steps) 1 µs Max. Jitter via CXP Trigger ±4 ns Max. Trigger frequency 300 kHz Quantum efficiency >45% @ 550 nm Interfaces... -
Page 21: Sensor Specifications
Sensor specifications Sensor type LUX13HS, CMOS global shutter Image sensor size 17.54 x 11.84 mm Resolution 1.1 Megapixel Active pixels 1.280 x 864 px ROI min 128 x 8 px Pixel depth 8 bit / 10 bit Pixel size 13.7 x 13.7 µm Light sensitivity 20 V/lux*s @ 550 nm (6,400 / 5,000 ASA) Dynamic range up to 60 dB... -
Page 22: Fig.: 5-1: Rear View (Fanless)
Fig.: 5-1: Rear view (fanless) 54,3 Fig.: 5-2: Side view (fanless) with C-mount adapter 5 Technical data... -
Page 23: Camera Dimensions (With Fan)
81,8 45,5 active sensor plane Fig.: 5-3: Side view (fanless) with F-mount adapter 81,8 45,5 active sensor plane Fig.: 5-4: Side view (fanless) with G-mount adapter 5.4.2 Camera dimensions (with fan) All dimensions in Millimeters. 5 Technical data... -
Page 24: Fig.: 5-5: Rear View (With Fan)
Fig.: 5-5: Rear view (with fan) 64,3 54,4 17,53 active sensor plane Fig.: 5-6: Side view (with fan) with C-mount adapter 5 Technical data... -
Page 25: Fig.: 5-7: Side View (With Fan) With F-Mount Adapter
93,0 83,1 46,5 active sensor plane Fig.: 5-7: Side view (with fan) with F-mount adapter 92,8 83,1 46,50 active sensor plane Fig.: 5-8: Side view (with fan) with G-mount adapter 5 Technical data... -
Page 26: Spectral Response
Spectral response 5.5.1 Monochrome and color Monochrome Fig.: 5-9: Spectral response - monochrome Color Fig.: 5-10: Spectral response - color 5 Technical data... -
Page 27: Appendix
Appendix The following page contains the Declaration(s) of Conformity. 6 Appendix... -
Page 28: Declaration Of Conformity
Address: Mikrotron GmbH Landshuter Str. 20-22 , 85716 Unterschleißheim Series: EoSens Creation 1.1CXP2 Model: CAMMC1166-352-2, CAMMC1167-352-2 The product complies with the requirements of the following European directives: 2014/30/EU Electromagnetic Compatibility (EMC) Restriction of the use of certain hazardous substances in 2011/65/EU + electrical and electronic equipment (RoHS) 2015/863/EU... - Page 29 SVS-Vistek GmbH Ferdinand-Porsche-Str. 3 82205 Gilching Phone: +49 8105 3987-60 https://www.svs-vistek.com info@svs-vistek.com © 09-2022 This document and the product(s) described are subject to change without further notice.
Need help?
Do you have a question about the CoaxPress EoSens Creation 1.1CXP2 and is the answer not in the manual?
Questions and answers