Table of Contents
Advertisement
described in the Assembly section of this manual.
If the blade is out of 45° bevel accuracy, adjust by tightening or
loosening the bevel stop adjustment screw.
Retighten bevel lock knob and push single/ dual bevel selector
in. Recheck blade-to-table alignment.
NOTE: The above procedure can be used to check the
accuracy of the saw blade to the turning table at both left and
right 45° angles.
have been made, it may be necessary to loosen the indicator
0° BEVEL ADJUSTMENT
NOTE: These adjustments were made at the factory and normally
Remove the battery pack from the product.
Loosen the bevel lock knob by turning the knob counterclockwise.
Assembly section of this manual.
loosening the 0° bevel stop screw using the 3 mm leg (short
leg) of a hex key.
Retighten bevel lock knob. Recheck blade-to-table alignment.
have been made, it may be necessary to loosen the indicators
TO ADJUST THE MITRE ANGLE
Loosen the sliding fence adjustment knob. Remove the sliding
fence.
Loosen the 4 screws for adjusting mitre angle on the fixed
fence. Ensure that the fixed fence can be moved.
NOTE:
saw blade, not the blade teeth.
Adjust the fixed fence until the flat part of saw blade and the
Tighten the 4 screws for adjusting mitre angle on the fixed
fence.
Install the sliding fence. Tighten the sliding fence adjustment
knob securely.
REMOVING/REPLACING THE ADJUSTABLE THROAT PLATES
throat plates away from the saw blade. Once the saw's alignment
Never operate the saw without the throat plates installed.
Remove the battery pack from the product.
Using the blade wrench provided, loosen the screws securing
the right side of the adjustable throat plate.
NOTE: The throat plate may be adjusted to (near) zero clearance
to support thin materials.
Slide the throat plate away from the blade as far as possible.
Retighten the screws, being careful not to overtighten which can
cause the throat plate to bow or bend.
Repeat the above steps for the left side of the throat plate.
TO ADJUST THE MITRE LOCK LEVER
In the locked position, the mitre lock lever should feel tight and
turning table. If the mitre lock lever feels loose or the table moves
easily when in the locked and unindexed position, an adjustment to
To adjust:
Remove the battery pack from the product.
Lift the mitre lock lever.
Remove the screws securing the throat plates, remove both
throat plates and set aside.
Locate the lock nut and tensioning nut.
Using a blade wrench, loosen the lock nut and adjust the
tensioning nut until the proper amount of tension in the lock
lever is attained.
Be sure to disconnect the product from the power supply before
attaching or removing the saw blade.
TRANSPORTATION AND STORAGE
When storing the product, remove the battery pack. Store the
product in a secure place that is not accessible to children.
Clean the product using a brush and vacuum cleaner before
storage.
If you remove the saw blade or keep spares with the unit, ensure
they are in the original packaging to prevent injury.
To secure the product prior to movement:
The product should be stored at the zero degree mitre and
bevel angle and locked in position. The slide should be locked.
The handle should be locked in the lower (safe) position with
the guards closed.
To move or transport in a vehicle:
Secure the product prior to movement as described in the
manual.
Remove the product from the bench top by releasing the 4 bolts,
one at each corner. Secure the bolts for future use. Lifting the
product using the handle at the top.
When lifting to a height, two persons are needed to hold the lift
handles on each side of the saw base firmly.
When transporting in a vehicle, set the product on its base and
secure against movement.
BATTERIES
Battery packs which have not been used for some time should be
recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance
of the battery pack. Avoid extended exposure to heat or sunshine
(risk of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully charged,
after used.
To obtain the longest possible battery life remove the battery pack
from the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C
and away from moisture.
Store the battery packs in a 30% - 50% charged condition.
Every six months of storage, charge the pack as normal.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods
Transportation of those batteries has to be done in accordance with
local, national and international provisions and regulations.
25
25
Advertisement
Table of Contents
