Table of Contents
Advertisement
the saw arm to prevent sudden rise upon release of the tie wrap.
Inspect the product carefully to make sure no breakage or
damage occurred during shipping.
Do not discard the packing material until you have carefully
inspected and satisfactorily operated the product.
The product is factory set for accurate cutting. After assembling
it, check for accuracy. If shipping has influenced the settings,
refer to specific procedures explained in the manual.
WARNING
If any parts are damaged or missing, do not operate the product
until the parts are replaced. Use of the product with damaged or
missing parts could result in serious personal injury.
WARNING
Do not attempt to modify the product or create accessories not
recommended for use with the product. Any such alteration or
leading to possible serious personal injury.
WARNING
To prevent accidental starting that could cause serious personal
injury, always remove the battery pack from the product when
assembling parts.
MOUNTING HOLES
WARNING
Before starting any cutting operation, mount the product to a
a crouched position. Failure to heed this warning can result in
serious personal injury.
as a workbench, mounting board. Four bolt holes have been
provided in the saw base for this purpose. Each of the four mounting
holes should be bolted securely using 7.9 mm (5/16 in.) machine
bolts, lock washers, and hex nuts (not included). Bolts should be
hex nuts, and the thickness of the workbench. Tighten all four bolts
securely.
Carefully check the workbench after mounting to make sure that no
movement can occur during use. If any tipping, sliding, or walking is
INSTALLING CARRYING HANDLE
Remove the screws and nuts from the carrying handle and set
aside.
Slide the carrying handle onto the saw arm, aligning the holes
on the arm with the holes in the handle.
Insert the screws and nuts into the holes and tighten securely.
Only use the lift handles on the table and/or the carrying handle
on top to move or carry the product. Never use the "D" handle and
always remove the battery before moving. Carrying the product
with the "D" handle may cause inadvertent switch actuation and
may result in serious personal injury.
BLADE WRENCH
A blade wrench is packed with the product. One end of the wrench
is a Phillips screwdriver and the other end is a hex key. Use the
hex key end when installing or removing blade and the Phillips end
when removing or loosening screws. A storage area for the blade
wrench is located in the carrying handle on the top of the product.
INSTALLING SLIDING FENCE
Turn the sliding fence adjustment knob counterclockwise, to
clear fence slots.
Install the sliding fence. Lower fence into fence slot. Be sure
side of fence lines up flush with side of fixed fence.
Tighten sliding fence adjustment knob securely.
NOTE: To remove the sliding fence, loosen the sliding fence
adjustment knob. Then, slide the fence towards the blade to take
out.
INSTALLING THE WORK CLAMP
In some operations, the work clamp assembly may interfere with
the operation of the blade guard assembly. Always make sure
there is no interference with the blade guard prior to beginning
any cutting operation to reduce the risk of serious personal injury.
The work clamp provides greater control by clamping the workpiece
to the table. It also prevents the workpiece from creeping towards
the saw blade.
Depending on the cutting operation and the size of the workpiece,
it may be necessary to use a C-clamp (not included) instead of the
work clamp to secure the workpiece prior to making the cut.
To install the work clamp:
Place the shaft of the work clamp in either hole on the turning
table base.
Rotate the work clamp knob on the work clamp to move it in or
out as needed.
NOTE: Many of the illustrations in this manual show only portions
of the product. This is intentional so that we can clearly show points
being made in the illustrations. Never operate the product without all
guards securely in place and in good operating condition.
DUST BAG
To install the dust bag and frame assembly, slide the open end
of the frame onto the exhaust port.
For efficient operation, empty the dust bag before it is half full.
This will permit better air flow through the bag.
17
WARNING
WARNING
17
Advertisement
Table of Contents
