Tektronix TMT4 Specification And Performance Verification Technical Reference
Margin tester
Hide thumbs
Also See for TMT4:
- Installation and safety instructions (64 pages) ,
- User manual (44 pages)
Related Manuals for Tektronix TMT4
Summary of Contents for Tektronix TMT4
- Page 1 TMT4 Margin Tester Specifications and Performance Verification Register now! Click the following link to protect your product. www.tek.com/register *P077173300* 077-1733-00...
- Page 2 Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or suppliers, and are protected by national copyright laws and international treaty provisions. Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supersedes that in all previously published material. Specifications and price change privileges reserved.
-
Page 3: Table Of Contents
PCIe signal system ................................ 9 Reference clock................................9 Trigger system (Not yet supported)..........................10 Controls and indicators..............................10 Communication ports..............................10 Ground strap attachment.............................. 10 Power source................................10 Mechanical characteristics..............................10 Performance verification procedure.............................11 Index......................................14 TMT4 Margin Tester Specifications and Performance Verification... -
Page 4: Important Safety Information
Important safety information Important safety information This manual contains information and warnings that must be followed by the user for safe operation and to keep the product in a safe condition. To safely perform service on this product, see the Service safety summary that follows the General safety summary. General safety summary Use the product only as specified. -
Page 5: Terms In This Manual
When this symbol is marked on the product, be sure to consult the manual to find out the nature of the potential hazards and any actions which have to be taken to avoid them. (This symbol may also be used to refer the user to ratings in the manual.) TMT4 Margin Tester Specifications and Performance Verification... -
Page 6: Service Safety Summary
This section lists the safety and environmental standards with which the instrument complies. This product is intended for use by professionals and trained personnel only; it is not designed for use in households or by children. Compliance questions may be directed to the following address: Tektronix, Inc. PO Box 500, MS 19-045 Beaverton, OR 97077, USA tek.com... - Page 7 Measurement Category II. For measurements performed on circuits directly connected to the low-voltage installation. • Measurement Category III. For measurements performed in the building installation. • Measurement Category IV. For measurements performed at the source of low-voltage installation. TMT4 Margin Tester Specifications and Performance Verification...
-
Page 8: Environmental Compliance
This symbol indicates that this product complies with the applicable European Union requirements according to Directives 2012/19/EU and 2006/66/EC on waste electrical and electronic equipment (WEEE) and batteries. For information about recycling options, check the Tektronix Web site (www.tek.com/productrecycling). Battery recycling This product contains a small installed lithium metal button cell. -
Page 9: Specifications
Peak - to - peak differential 0.3 V - 1.5 V input voltage Output characteristics 85 Ω differential source terminated system The M.2 Edge adapter does not use the TMT4 cable in its setup. TMT4 Margin Tester Specifications and Performance Verification... -
Page 10: Trigger System (Not Yet Supported)
Specifications Output frequency PCIe compliant reference clock including 100 MHz common clock or SSC enabled (30 - 33 kHz) Output frequency accuracy 100 MHz reference clock with ±300 ppm frequency stability Trigger system (Not yet supported) Input characteristics 50 Ω single ended Input max voltage 3.3 V Output characteristics... -
Page 11: Performance Verification Procedure
Performance verification procedure The following procedure verifies the end-to-end PCIe link for TMT4 → TMT4 cable → TMT4 adapter → PCIe enabled device. A failing result can indicate a fault in any one of those components in the system. Additional troubleshooting may be required to identify any cause of fault. - Page 12 Click the Setup button and verify that the system is in the correct setup to run your connected add-in card scans. If needed, reboot the TMT4 to AIC setup. A Reboot button should appear if this is needed. Set the Test Type to Quick Scan.
- Page 13 Verify fully seated connections (unplug and replug). b. Verify external power is attached and on as needed by the DUT. 15. Once troubleshooting is complete, run the Gen 3 Quick Scan again. TMT4 Margin Tester Specifications and Performance Verification...
-
Page 14: Index
Index Communication ports Controls and indicators Ground strap attachment High density bidirectional signal system Mechanical characteristics PCIe signal system Performance verification procedures Power source Reference clock Specifications Trigger system...