Advertisement
Quick Links
Programming PowerFlex Drives (70, 70EC, 700Std, 700VC Series A & B)/ SMC Flex
Soft Starters with 20-HIM-A3 or 20-HIM-A5 External Door Mounted HIM
Direction
Drive Status
Key Descriptions
Escape
ESC
Pressing the Escape Key once takes you back one level.
Select
Sel
When at the parameter level pressing select will move the cursor to the line of the
Display where the parameter value is. Then you are able to change its value. If the value
of the parameter is at a Bit level then repeatedly pressing the Select key will move the
cursor from one bit to the next (going from right to left).
Up and Down Arrows
Allows you to move between the different levels in the menu. When changing the
parameter value these will increase or decrease the value. The longer you hold down the
key the faster it changes the value.
Enter (This is the Universal key/Symbol used for "Enter")
Pressing this key will select the Item Highlighted in the menu and take you to the
next level. Pressing this key when the value of a parameter has been changed will
then write the changed value to the drive.
Alarm
Auto/Man
Information (The ALT View Function is allowed)
This is the "User Display" Window – The drive
typically defaults to this window after 30 seconds
This is User Display Line 0
This is User Display Line 1
This is User Display Line 2
Blue Programming Keys
Programming Instructions shown using a 20-HIM-A3
1
Advertisement
Related Manuals for Allen-Bradley PowerFlex 20-HIM-A3
Summary of Contents for Allen-Bradley PowerFlex 20-HIM-A3
- Page 1 Programming PowerFlex Drives (70, 70EC, 700Std, 700VC Series A & B)/ SMC Flex Soft Starters with 20-HIM-A3 or 20-HIM-A5 External Door Mounted HIM Direction Drive Status Alarm Auto/Man Information (The ALT View Function is allowed) This is the “User Display” Window – The drive typically defaults to this window after 30 seconds This is User Display Line 0 This is User Display Line 1...
- Page 2 Key Descriptions continued Programming Instructions shown using a 20-HIM-A3 Key Descriptions Start Pressing Start will cause the Drive Output/Power IGBT’s to start modulating or put the drive in a run condition. If no start inhibit is present, Mask, fault or alarm. If a digital input is programmed for 2 wire control.
- Page 3 Key Descriptions continued Programming Instructions shown using a 20-HIM-A3 Key Descriptions Change Direction Pressing the change direction key will cause the Drive/Motor to go in the opposite Direction. Unless a mask is set to lock out this function. Or reverse disable P190 Digital Pot Up and Down Arrows When the HIM is used as the speed reference.
-
Page 4: Function Examples
Key Descriptions ALT (using the ALT Key) The ALT key is Color coded Yellow for 2 function. This means whenever the ALT Key is Pressed and Released the Keys that are labeled in Yellow text that is their 2 function And are now available to be selected within a 3 sec time frame. - Page 5 Press and Release Alternate (ALT) This is displayed for Approximately 3 seconds Key is Active Press and Release SMART List: Digital IN2 Sel Then Stop/Brk Mode A Press and Release Minimum Speed S.M.A.R.T Displays the “S.M.A.R.T” Start-up menu. (Starting At the “User Display” window) Press and Release 0.00 Then...
- Page 6 Press and Release Auto Manual Go to HIM Manual Then Speed Control? () Press and Release Press Enter Auto / Man (To toggle between HIM and Auto control of the Drive – when using the HIM) Press and Release Remove HIM Do you wish to? Then To Continue...
- Page 7 Press and Release Press and Release Param Dspy Item: File Group Then Then Numbered List Press and Release Press and Release Changed Params View View Provides the selection of how parameters will be viewed and continued to be viewed this way even when AC power has been cycled.
- Page 8 Press and Release Then Press and Release View Then This window will be displayed Use the Up and Down Arrows to Highlight Numbered List Then Press the Enter Key Then This window will be displayed Then Press Enter and this window will be displayed Key in any parameter number you want to go to - then Press and Release the Enter key.