Juniper T4000 Quick Start Manual
  1. Manuals
  2. Brands
  3. Juniper Manuals
  4. Network Router
  5. T4000 -
  6. Quick start manual

Juniper T4000 Quick Start Manual

Core router
Hide thumbs Also See for T4000:
Table of Contents

Advertisement

Quick Links

Download this manual
T4000 Core Router Quick Start
March 2012
Part Number: 530-046043
Revision 01
Contents
Copyright © 2012, Juniper Networks, Inc.
This document describes how to install the T4000 Core Router.
Quick Start Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Step 1: Preparing the Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Rack-Mounting Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Step 2: Installing the Mounting Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installing Cage Nuts, If Needed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Installing the Large Mounting Shelf and Spacer Bars . . . . . . . . . . . . . . . . 8
Installing the Small Mounting Shelf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Removing the Center-Mounting Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Installing Cage Nuts, If Needed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Installing the Large Mounting Shelf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Step 3: Installing the T4000 Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Installing the Router Using a Lift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Installing the Router Without a Mechanical Lift . . . . . . . . . . . . . . . . . . . . . . . . 13
Removing Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Lifting the Router into the Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Reinstalling Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Step 4: Connecting the Grounding Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Step 5: Connecting External Devices and PIC Cables . . . . . . . . . . . . . . . . . . . . . . . 20
Connecting to a Console or Auxiliary Device . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Connecting the PIC Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Connecting to a Network for Out-of-Band Management . . . . . . . . . . . . . . . . 22
Step 6: Connecting Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Step 7: Powering On the Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Powering On the DC-Powered Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the T4000 and is the answer not in the manual?

Questions and answers

Related Manuals for Juniper T4000

Summary of Contents for Juniper T4000

  • Page 1: Table Of Contents

    Step 3: Installing the T4000 Router ........
  • Page 2 T4000 Core Router Quick Start Step 8: Performing the Initial Software Configuration ..... . 30 Preparing to Configure the Router ........30 Entering Configuration Mode .

  • Page 3: Quick Start Description

    Quick Start Description This Quick Start contains information you need to install and configure the router quickly. For complete installation instructions, see the T4000 Core Router Hardware Guide http://www.juniper.net/techpubs/hardware/ WARNING: This Quick Start contains a summary of safety warnings in “Safety...

  • Page 4: Step 1: Preparing The Site

    T4000 Core Router Hardware Guide Rack-Mounting Requirements on page 4 Tools Required to Unpack and Prepare the T4000 Router for Installation on page 5 Rack-Mounting Requirements You can install the router in many types of racks, including a four-post rack or cabinet or an open-frame rack.
  • Page 5 Tools Required to Unpack and Prepare the T4000 Router for Installation Figure 1: Rack Clearances and Router Dimensions Tools Required to Unpack and Prepare the T4000 Router for Installation A mechanical lift—recommended 1/2-in. or 13-mm open-end or socket wrench to remove bracket bolts from the shipping...
  • Page 6 T4000 Core Router Quick Start Antistatic mat Blank panels to cover any slots not occupied by a component Copyright © 2012, Juniper Networks, Inc.

  • Page 7: Step 2: Installing The Mounting Hardware

    Table 1: Four-Post Rack and Cabinet Mounting Hole Locations Hole Distance Above U Division Large Shelf Spacer Bars Small Shelf 34.75 in. (88.3 19.86 U – – 29.51 in. (74.9 16.86 U – – Copyright © 2012, Juniper Networks, Inc.

  • Page 8: Installing Cage Nuts, If Needed

    T4000 Core Router Quick Start Table 1: Four-Post Rack and Cabinet Mounting Hole Locations (continued) Hole Distance Above U Division Large Shelf Spacer Bars Small Shelf 24.26 in. (61.6 13.86 U – – 19.01 in. (48.3 10.86 U – 13.76 in. (34.9 7.86 U...

  • Page 9: Installing The Small Mounting Shelf

    Center-mounting: Attach the large mounting shelf on the back of the rails. The small mounting shelf is not needed for open-frame racks.Table 2 on page 10 specifies the holes in which you insert mounting screws and cage nuts (if needed). Copyright © 2012, Juniper Networks, Inc.
  • Page 10 T4000 Core Router Quick Start Figure 3: Mounting Hardware for an Open-Frame Rack An x in Table 2 on page 10 indicates a mounting hole location. Table 2: Open-Frame Rack Mounting Hole Locations Hole Distance Above U Division Large Shelf 34.13 in.

  • Page 11: Installing Cage Nuts, If Needed

    If you plan to center-mount the router in an open-frame rack, leave the center-mounting brackets attached to the chassis. Optionally, you can remove the spacer bars from the front-mounting flanges. Copyright © 2012, Juniper Networks, Inc.

  • Page 12: Step 3: Installing The T4000 Router

    T4000 Core Router Quick Start Step 3: Installing the T4000 Router Because of the router's size and weight, we recommend that you install the router using a mechanical lift. If a lift is unavailable, see the instructions for installing the rack without a mechanical lift.

  • Page 13: Installing The Router Without A Mechanical Lift

    Open-frame rack: Install a mounting screw into each of the open mounting holes aligned with the rack, starting from the bottom. Reinstall the power supplies as described in the T4000 Core Router Hardware Guide Figure 4: Loading the Router onto the Lift Installing the Router Without a Mechanical Lift...

  • Page 14: Removing Components

    T4000 Core Router Quick Start Removing Components NOTE: For complete instructions on removing router components, see the T4000 Core Router Hardware Guide Before lifting the router, you must remove the following components (see the location of the components in Figure 5 on page 15...
  • Page 15 Removing Components Figure 5: Location of Components to Remove from the Front of the Router Fan tray T Se ries FPCs FANTR AY-T40 00 FA NT RA Y-T 40 00 Fan tray Copyright © 2012, Juniper Networks, Inc.

  • Page 16: Lifting The Router Into The Rack

    T4000 Core Router Quick Start Figure 6: Location of Components to Remove from the Rear of the Router Fan tray SCGs Control board 0 Control board 1 SIBs Power supply 0 Power supply 1 Lifting the Router into the Rack...
  • Page 17 Four-post rack or cabinet: Install a mounting screw into each of the holes aligned with the threaded holes in the spacer bars. Open-frame rack: Install a mounting screw into each of the open mounting holes aligned with the rack, starting from the bottom. Copyright © 2012, Juniper Networks, Inc.

  • Page 18: Reinstalling Components

    T4000 Core Router Quick Start Figure 7: Lifting the Router into the Rack Reinstalling Components NOTE: For complete instructions on reinstalling router components after you have installed the router without a mechanical lift, see the T4000 Core Router Hardware Guide Slide each component into the chassis evenly so that it does not become stuck or damaged.

  • Page 19: Step 4: Connecting The Grounding Cable

    Verify that the grounding cabling is correct, that the grounding cable does not touch or block access to router components, and that it does not drape where people could trip on it. Figure 8: Connecting the Grounding Cable Grounding points (on chassis) Copyright © 2012, Juniper Networks, Inc.

  • Page 20: Step 5: Connecting External Devices And Pic Cables

    T4000 Core Router Quick Start Step 5: Connecting External Devices and PIC Cables To connect external devices and PIC cables, perform the following procedures: Connecting to a Console or Auxiliary Device on page 20 Connecting the PIC Cables on page 21...

  • Page 21: Connecting The Pic Cables

    To prevent damage to fiber-optic transceivers and fiber-optic cables, observe the following precautions: Do not leave a fiber-optic transceiver uncovered except when inserting or removing cable. The safety cap keeps the port clean and prevents accidental exposure to laser light. Copyright © 2012, Juniper Networks, Inc.

  • Page 22: Connecting To A Network For Out-Of-Band Management

    T4000 Core Router Quick Start Do not bend fiber-optic cable beyond its maximum bend radius. An arc smaller than a few inches in diameter can damage the cable and cause problems that are difficult to diagnose. Do not let fiber-optic cable hang free from the connector. Do not allow fastened loops of cable to dangle which stresses the cable at the fastening point.
  • Page 23 Plug the other end of the cable into the network device. Figure 12: Routing Engine Ethernet Cable Connector Figure 13: ETHERNET Port on the CIP T Ser ies FANTR AY-T40 00 FAN TR AY- T40 Copyright © 2012, Juniper Networks, Inc.

  • Page 24: Step 6: Connecting Power

    Guide Connecting DC Power to the T4000 Router (Six 60-A Inputs) on page 24 Connecting DC Power to the T4000 Router (Six 60-A Inputs) You connect DC power to the router by attaching power cables from the DC power sources to the terminal studs on the power supply faceplates.
  • Page 25 To connect DC source power cables to the router, follow this procedure for each DC power supply: Verify that a properly rated customer site circuit breaker for each DC power cable has been installed. See T4000 DC Power Electrical Safety Guidelines in the T4000 Core Router Hardware Guide for more information.
  • Page 26 T4000 Core Router Quick Start Figure 15: Connecting Negative (–) DC Power Cables to INPUT 0, INPUT 1, INPUT 3, and INPUT 4 Replace the smallest cable restraint on the far right, and tighten the captive screw to hold the power cables for , and in place.

  • Page 27: Step 7: Powering On The Router

    Replace the clear plastic cover over the terminal studs on the faceplate. Step 7: Powering On the Router Powering On the DC-Powered Router on page 28 Copyright © 2012, Juniper Networks, Inc.

  • Page 28: Powering On The Dc-Powered Router

    T4000 Core Router Quick Start Powering On the DC-Powered Router To power on the DC-powered T4000 router: Verify that the power supplies are fully inserted in the chassis and that the captive screws on their faceplates are tightened. Verify that the source power cables are connected to the appropriate terminal: the positive (+) source cable to the return terminal (labeled ) and the negative (–)
  • Page 29 Powering On the DC-Powered Router Figure 18: Six-Input DC Power Supply Copyright © 2012, Juniper Networks, Inc.

  • Page 30: Step 8: Performing The Initial Software Configuration

    T4000 Core Router Quick Start Step 8: Performing the Initial Software Configuration The T4000 Core Router is shipped with the Junos OS preinstalled and ready to be configured when the T4000 router is powered on. These procedures connect a router to the network but do not enable it to forward traffic.

  • Page 31: Configuring User Accounts And Passwords

    CLI. For example, this hostname shows on the command-line prompt when the user is logged on to the CLI: user-name@host-name> Configure the IP address of the DNS server. [edit] root# set system name-server address Copyright © 2012, Juniper Networks, Inc.

  • Page 32: Committing The Configuration

    T4000 Core Router Quick Start Configure the router’s domain name. [edit] root@# set system domain-name domain-name Configure the IP address and prefix length for the router’s management Ethernet interface. NOTE: The RE-C1800 Routing Engine ( ) does not support RE-DUO-1800 interface or the internal Ethernet interfaces.
  • Page 33 { 192.168.1.1; login { user regress { uid 2001; class super-user; authentication { encrypted-password "xxxxxxxxxxx"; ## SECRET-DATA services { telnet; syslog { user * { any emergency; file messages { any notice; authorization info; Copyright © 2012, Juniper Networks, Inc.
  • Page 34 T4000 Core Router Quick Start file interactive-commands { interactive-commands any; routing-options { static { /* corporate office */ route 172.16.0.0/12 { next-hop 192.168.71.254; retain; no-readvertise; Commit the configuration to activate it, and synchronize the configuration. The commit synchronize command commits this new configuration on both Routing Engines simultaneously.

  • Page 35: Safety Warnings

    For the six-input DC power supplies, each 48 VDC facility DC source input power cable must be equipped with a current-limiting fuse or circuit breaker external to the Juniper Networks equipment rated at 100 A (–48 VDC) maximum, or as required by local code.

  • Page 36: Compliance Statements For Nebs

    T4000 Core Router Quick Start Read the installation instructions before you connect the router to a power source. Before installing the router, read the guidelines for site preparation in the T4000 Core Router Hardware Guide to make sure that the site meets power, environmental, and clearance requirements for the router.

  • Page 37: Compliance Statements For Emc Requirements

    A est conforme à la norme NMB-003 du Canada. European Union This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Copyright © 2012, Juniper Networks, Inc.

  • Page 38: Declaration Of Conformity

    T4000 Core Router Quick Start Declaration of Conformity Junos OS Documentation and Release Notes For a list of related Junos OS documentation, see http://www.juniper.net/techpubs/software/junos/ If the information in the latest release notes differs from the information in the documentation, follow the Junos OS Release Notes.

  • Page 39: Requesting Technical Support

    7 days a week, 365 days a year. Self-Help Online Tools and Resources For quick and easy problem resolution, Juniper Networks has designed an online self-service portal called the Customer Support Center (CSC) that provides you with the following features: Find CSC offerings: http://www.juniper.net/customers/support/...

  • Page 40: Revision History

    Products made or sold by Juniper Networks or components thereof might be covered by one or more of the following patents that are owned by or licensed to Juniper Networks: U.S. Patent Nos. 5,473,599, 5,905,725, 5,909,440, 6,192,051, 6,333,650, 6,359,479, 6,406,312, 6,429,706, 6,459,579, 6,493,347, 6,538,518, 6,538,899, 6,552,918, 6,567,902, 6,578,186, and 6,590,785.

Table of Contents