ICS IDM-60R Quick Start Manual

IDM-60R Rs485
■

1. NOTICE

1. Please check the packaging and appearance after you received the
product.
2.Please check lhe mode and specification of the product. Keep
correct electrical connection and mounting method.
3.Please installation WITHOUT power.
4.During using, please notice the technical and operation condilions:
the temperature of medium, burst pressure, power supply.
5. This product is a precision device, DO NOT use hard objects to tauch
the diaphragm or disassemble.
6. During installation, do not install or disassemble strongly, especially
the installation of thread.
7. Please install or disassemble with a suitable wrench, Otherwise, the
damage is not in the scope of warranty.
8. After starting the gauge, it is a normal phenomenon to take a fe w
minutes to keep it stable and work normally.
9.lf the product is out of order, please contact our after-sale technical
staff.
1 0.During installation, the gauge will be affected by installation stress.
After installation, please zero clearing.
(!!)The product damage caused by non-professional operation
according to the operation regulation is not the scope by the warranty.
■

2. WARNING

1.When operation temperature is above 60 degree, please use forced
fans or cooling machines, but do not let the cooling air blow to the
s witch directly.
2.The installalion, commissioning and maintenance of this product
shall be conducted by qualified engineers or technicians member.
3.lf the malfunction or exception of this product is likely to result in a
major system accident, please sei up an appropriate protective circuit
outside to prevent accidents.
4.The company does not undertake any direct or indirect lass other
than the product itself.
5.The company reserves the right to change the manual of the product
without notice.
■

3. DESCRIPTION

This digital communication pressure gauge is a high-precision
intelligent digital remote pressure gauge based on MODBUS protocol
RS485 output.
The digital communication pressure gauge adopts a 4 digit LCD
screen, which can display real-time pressure on the spot. At lhe same
time, the pressure signal is transmitted remotely, and the transmission
distance is better than 1000 meters.
Built-in pressure sensor, powerful function, users can change
pressure uni!, calibrate zero deviation, correct filter constant, etc.
This digital communication pressure gauge adopts SS 304 housing
and connection, waterproof cable outlet, waterproof rating of IP65, and
a wide range of media suitability.
* With RS485 signal output
* Adopt standard MODBUS RTU communication protocol
* Adopt all 304 stainless steel shell, strong and durable
* High precision, lang transmission distance, stable performance
* Compact appearance, diameter 60mm
* Compact appearance, diameter 60mm
*High degree of intelligence, users can sei the address, baud rate,
filter constant, re-check, etc.
■

4. TECHNICAL SPECIFICATIONS

Pressure range
Vacuum range: (0--100)kPa
Compound range: -0.1-0.1 ... 0.25 0.6 1.0 1.6 2.5MPa
Micro pressure range: -100 ... -25 ... -5-2 ... 5 ... 25 ... 100kPa
Normal range: 0-0.16 ... 0.4 ... 1.0 ... 10 ... 25 ... 60MPa
Connection: M20*1.5, G1/4, G1/2, 1/4NPT, 1/2NPT
Accuracy: 0.5%FS, 0.25%FS
Display Digits: 4 digits LCD
Dimension: diameter 60mm thickness 38mm
Power: 12-28VDC( recommend 24VDC)
Output signal: Rs485
Output protocol: standard MODBUS RTU
Communication message: N81/N82/E81/O81
Sampling rate: 10 times/second
±
Output accuracy: 0.2%FS
Communication rate: 2400/4800/9600/19200/38400/57600bps
Power: <0.4W
Measurement medium: water, oil, air etc (non-corrosive medium for SS)
Transmission distance: 1000 meters
IP Rating: IP 65
OPERATION ENVIRONMENT:
°
Operation temperature:-20-80 (
1
°
Storage temperature:-40-125 (
■
Environment humidity: 0-95%RH

5. KEY DESCRIPTION

5.1 KEY DESCRIPTION

Key @ De finition Description
§
Set button Lang press to enter the parameter setting state
Short press increase
lncrease button When changing the password, lang press to
move the location
Short press to reduce
®
Decrease button When changing the password, lang press to
move the location

5.2 SCREEN DISPLAY

�88887
�AR Kgf/cm' PSI MP1 kP�

5.3 MODE DESCRIPTION

Status Description
Operation status Show current pressure and uni!
Short press lhe i§ first, then lang
Zero Calibration until the screen displays C--L, the zero clearing is
finished (clearing must be performed without pressing)
Note: When the display pressure is higher than 10%
of the range, it cannot b e cleared.
Setting status See the 8th item for the general setting operation method.
See the 9th item for how to sei the communication system .
I
■
6.DIMENSIONS
®J ____aa_
UIII
1 �
-
�
[
I B )
I
Radial installation
■
7.WIRING METHORDS
RS 485 Digital communication type
+
red/brown in
f24v
blue in ·
Digital communication
black A
pressure gauge
ite�B� __ RS 485
,-,w h
= =
I
Note: The definition of the outlet is subject to lhe actual label of the product.
■

8. FUNCTION SETTING

[First set of parameter settings]
1).Press and hold theif': � button for 2 seconds without releasing until the
L
Loc para!Tleler is displayed.
oc
2.Click @ or ('i" ) to get the parameter value, modify the bit flashing, lang
press @a) or(�)to move th_ e modified bit, press @ or (�) to modify the
parameter value, press E'.' ) key to save.
3.Change the password lock to 1111 and click the
next parameter of this group.
4.Click the set button to browse the parameter names in sequence, and
follow step @ to sei the parameters !hat need to be modified. When
reviewing or setting the last parameter of the first sei of parameters, click
lhe sei button to exit lhe setting.
[The first parameter setting codes]
Inne r
Display
S ym O Nam e Content
b
add. content
Loc Loc Password key 00H 0000-9999
Addr Mailing address 01H 1-25
Rclclc
bRud
bAud Communication 02H Note1
rate ootion
rdAt Communication data 03H Note3
.-dRI:
message forma
Fltr Filter constant 04H 0-20 Note5
FU:c
press@for 3 seconds
UNIT: mm
Axial installation
E• - �
button to display the
Read & write data
corresponding value
0000 H-271 FH
1 H-FFH
OH-SH Note2
0H-3H Note4
0H-14H