Subscribe to Our Youtube Channel
Related Manuals for ICS MultiPanel 2025
Summary of Contents for ICS MultiPanel 2025
- Page 1 MultiPanel 2025 Operating Instructions Version 1.0 ENG Firmware-Version 1.2 TKZ L3160-00-80.00EN...
-
Page 2: Table Of Contents
OPERATING INSTRUCTIONS Basics ........3 Resetting menu language ....23 Intended use . -
Page 3: Basics
Basics BASICS Disposal of the measuring instrument Disposal information This instruction manual is part of the MultiPanel 2025 Do not dispose of this product with your instrument. It contains the information necessary for household waste. safe use. Read this manual before starting up the in- You can find more detailed information on strument. -
Page 4: Description Of The Measuring Instrument
Display Menu key Function keys On/off button (F4) The MultiPanel 2025 is a measuring instrument which provides the user with all functions needed for profes- sional and challenging metrology. When using sensors with ISDS (intelligent sensor de- tection), the measuring instrument automatically iden-... -
Page 5: Plug Connector 1
Description of the measuring instrument Plug connector 1 Label Function U/F1 Analog signal input 10V Direction detection f-signal from channel 1 U/F2 Analog signal input 10V Direction detection f-signal from channel 2 Power supply sensor 1 (+Ub or 14VDC) Power supply sensor 2 (+Ub or 14VDC) Label Function... -
Page 6: Operating Keys
Opens the menu for deleting measure- ment sere. Switches the view of the selected meas- urement or special channel on or off. Displays USB status: • Instrument connected with USB. • Instrument is communicating via USB. Displays battery status: Full, half-full, empty. MultiPanel 2025... -
Page 7: Start-Up
Start-up START-UP The display shows the firmware version number and serial number of the measuring instrument. Basic settings The display then shows the calibration notice. When you switch on the measuring instrument for the first time, you are asked to define the basic settings. How to define the basic settings [F4] Press... -
Page 8: Time And Date
Set the time format and time: [F1] format time • Use to select and press [MENU] [F1] [F2] • Press to change the selected value. [MENU] • Press to save your entry. [F4] DEVICE Press to return to the menu. MultiPanel 2025... -
Page 9: Calibration Interval
Calibration interval [F1] Calibration CALIBRATION INTERVAL Press to select the entry and [MENU] CALIBRATION to open the menu. The measuring instrument was calibrated before it was shipped by the manufacturer. The calibration in- terval is the period of time after which the measuring instrument is to be re-calibrated by the manufacturer. -
Page 10: Hydrocenter
PC or notebook. Follow the instructions displayed there. The installation file is downloaded. Run the installation file. Confirm the confirmation prompts, if applicable. Follow the installation instructions. The installation is complete when the link is dis- played on the desktop. MultiPanel 2025... -
Page 11: Firmware Update
HYDROcenter Firmware update Note Instrument damage during firmware update If there is new firmware for your measuring instru- Errors during the firmware updates can damage ment, HYDROcenter offers you an update. the measuring instrument. Save all stored measurement series (e.g. with •... -
Page 12: Measurement
• A zero adjustment cannot be executed for chan- nels showing a frequency. • No zero adjustment can be done for the following channels: C4, C5, C6, C7, C8. • Measurement values are set to zero for channels configured as counters. MultiPanel 2025... -
Page 13: Saving And Deleting Measurement Series
Measurement [F3] Min./max. Display Start the measurement series by pressing [F1] Pressing switches to min./max. display or back The display shows a progress bar on the right to the current measurement values. side. [F2] Press to display the current memory status. Maximum values Minimum values [F2]... -
Page 14: Channels
[MENU] MAIN MENU Press to open the ment values again. [MENU] CHANNELS to open the menu. If you have switched on the display view for no channel or several channels, the following error is displayed: MultiPanel 2025... -
Page 15: Channels C1 And C2
Channels Configuring measurement channels C1 and C2 Measurement variable Unit of (measurand) measurement If you are using a sensor without ISDS, you have to Speed [mm/s] configure a channel. You need a corresponding pa- Angular speed [°/s] rameter for the sensor. They are on the sensor or in Ground [to] the sensor data sheet. - Page 16 Press until the display shows the measure- Configure the measurement variables: ment values again. [MENU] • Press [F1] [F2] • Press to change the measure- ment variable and unit of measurement. [MENU] • Use to save your entry. MultiPanel 2025...
-
Page 17: Configuring Special Channel C3
Display Meaning of trigger input Inverse logic of the trigger input The trigger input of the MultiPanel 2025 is not, as for other measuring instruments from Hydrotech- nik GmbH; instead, it has an inverse logic. The trigger input is switched on ( ) if nothing is connected to the input. -
Page 18: Configuring Trigger And Relay Outputs C5 And C6
[MENU] • Press to save your entry. [F4] The following values can be shown on the display: Press until the display shows the measure- ment values again. Display Meaning of trigger output Display Meaning of relay output MultiPanel 2025... -
Page 19: Configuring Analog Outputs C7 And C8
Channels Configuring analog outputs C7 and C8 Configure the output range: [F1] Range • Press to select [MENU] The operation of the menus for trigger output ( • Press [F1] [F2] and relay output ( ) is identical. • Press to change the first digit. -
Page 20: Instrument Configuration
[MENU] Press to save your entry. [F4] DEVICE Press to leave the menu. [F1] Press three times to display the second page DEVICE of the menu. [F4] DEVICE Press to leave the menu. MultiPanel 2025... -
Page 21: Units
Instrument configuration Units How to change the display rate DEVICE [F1] Open the menu and use to select Unit Disp.rate Use the setting to change the unit system of the entry. How to open the DEVICE menu, page 20 measuring instrument. -
Page 22: Time
Error code Information text Date of last calibration Date [F4] You must confirm the information with in order to Read the following section for information on the DATE MENU use the measuring instrument. Time and date, page 8 MultiPanel 2025... -
Page 23: Resetting Menu Language
Resetting menu language RESETTING MENU LANGUAGE RESETTING MEASURING INSTRUMENT If the measuring instrument is set to the incorrect lan- You can reset the measuring instrument. Resetting guage, you may not be able to operate it. has the following effects: CHANNELS You can reset the menu language without under- •... -
Page 24: Error Codes
Error codes ERROR CODES TECHNICAL DATA Code Description Property Value 8100 Error in flash memory during read and Dimensions (H x W x D) 96 x 96 x 60mm write test Weight 298 g 8101 Flash memory could not be deleted Temperature range -20...+50 °C 8102... - Page 25 Technical data...
- Page 26 Technical data...
- Page 27 Technical data...
Need help?
Do you have a question about the MultiPanel 2025 and is the answer not in the manual?
Questions and answers