ICS IDM-60A Quick Start Manual

IDM-60A 4-20mA
■
1. NOTICE
1. Please check the packaging and appearance after you received
the product.
2.Please check the mode and specification of the product. Keep
correct electrical connection and mounting method.
3.Please installation WITHOUT power.
4.During using, please notice the technical and operation conditions:
the temperature of medium, burst pressure, power supply.
5. This product is a precision device, DO NOT use hard objects to
tauch the diaphragm or disassemble.
6. During installation, do not install or disassemble strongly,
especially the installation of thread.
7. Please install or disassemble with a suitable wrench, Otherwise,
the damage is not in the scope of warranty.
8. After starting the gauge, it is a normal phenomenon to take a few
minutes to keep it stable and work normally.
9. lf the product is out of order, please contact our after-sale technical
staff.
10.During installation, the gauge will be affected by installation
stress. After installation, please zero clearing.
(!!)The product damage caused by non-professional operation
according to the operation regulation is not the scope by the warranty.
■
2. WARNING
1.When operation temperature is above 60 degree, please use forced
fans or cooling machines, but do not let the cooling air blow to the
switch directly.
2.The installation, commissioning and maintenance of this product
shall be conducted by qualified engineers or technicians member.
3.lf the malfunction or exception of this product is likely to result in a
major system accident, please sei up an appropriate protective
circuit outside to prevent accidents.
4.The company does not undertake any direct or indirect lass other
than the product itself.
5.The company reserves the right to change the manual of the
product without notice.
■
3. DESCRIPTION
This remote transmission pressure gauge is an economical digital
pressure transmitter with a built-in high-precision pressure sensor,
which can accurately display the pressure in real time and transmit
the pressure signal remotely. lt has the characteristics of high
accuracy and good long-term stability.
This remote transmission pressure gauge adopts LCD display, with
multiple functions such as uni! switching, zero calibration, full scale
correction, digital filtering, etc., simple operation and convenient
installation.
This product can measure water, oil, air and other non-corrosive
media to stainless steel, and can replace the traditional pointer type
remote pressure gauge or pressure transmitter.
■
4. TECHNICAL SPECIFICATIONS
Pressure range: -0.1-0.1 ... 0.6 ... 1 ... 1.6 ... 2.5 ... 6 ... 10 ... 60MPa
Pressure type: gauge pressure, negative gauge pressure
Overload pressure: <10MPa 200%; :?10MPa 150%
Accuracy grade: 0.5% FS
Long-term stability: 0.5% FS/year
Power supply: 12-28VDC (24VDC)
Output signal: 4-20mA
Load impedance: S500O
Operation temperature: -20-60"C
Display screen: 4-digits LCD display
Backlight color: white
Measuring medium: air, water, oil and other non-corrosive media to stainless
steel.
Case material: 304 stainless steel
Connection material: 304 SS (or customized)
Product functions: uni! switching, clearing, digital filter adjustment
■
5. KEY DESCRIPTION
D
008
5.1 KEY DESCRIPTION
Key De fi nition Description
§
Set key Lang press to enter parameter setting state
Short press to increase
@
lncreasing key When changing the password, lang press to
<>hift
© Short press to enter system function,
Decreasing key
adjust the number short press to decrease
5.2 LCD DISPLAY
Status Description
Operation status Display current pressure and uni!
®
Short press the key, and then lang press
Zero correction seconds until the screen displays C-L, and the reset is
completed (the reset must be operated without pressure)
Note: When the display pressure is higher than 10%
of the range, it cannot be cleared
Setting status Refer to item 7 for general setting operation method
@
for 5