Download
Share
Print this page
Microtek ScanMaker 5950 Install Manual
  1. Manuals
  2. Brands
  3. Microtek Manuals
  4. Scanner
  5. ScanMaker 5950
  6. Install manual

Microtek ScanMaker 5950 Install Manual

Microtek scanmaker 5950: install guide
Hide thumbs Also See for ScanMaker 5950:
1
2
3
4
5
6
7
8

Advertisement

Quick Links

Download this manual See also: User Manual
Microtek ADF-650/651
Installing and Getting Started
This document describes the features of
the Automatic Document Feeder (ADF-650/
651) and provides information on how to
install the ADF-650/651.
The ADF-650/651 is an optional sheet feeder accessory for the Microtek ScanMaker-
series of flatbed scanners. The ADF-650 is designed for the ScanMaker 5600,
ScanMaker 6700, and ScanMaker 6800, while the ADF-651 is designed for the
ScanMaker 5800 and ScanMaker 5900.
The ADF-650/651 allows automatic scanning of up to 50 sheets of original scan
material from A6 size (4.14" x 5.83") up to legal size (8.5" x 14"). Sheets to be scanned
are fed from the feeder's top tray, guided and scanned as they pass the scanner's
image sensor, and then exit into the feeder's bottom tray.
The ADF-650/651 mounts onto the scanner in place of the scanner's document cover
Trademarks
or Transparent Media Adapter (TMA).
The ADF-650/651 is packaged as an assembled unit, ready to be mounted on the
scanner. After unpacking the ADF-650/651, make sure that the following items are
included:
• ADF-650/651 unit
Important
• Warranty Card
• ADF-650/651 Installing and Getting Started document
Introduction
Checking the Package

Advertisement

loading

Related Manuals for Microtek ScanMaker 5950

Summary of Contents for Microtek ScanMaker 5950

  • Page 1 ADF-650/651. Introduction The ADF-650/651 is an optional sheet feeder accessory for the Microtek ScanMaker- series of flatbed scanners. The ADF-650 is designed for the ScanMaker 5600, ScanMaker 6700, and ScanMaker 6800, while the ADF-651 is designed for the ScanMaker 5800 and ScanMaker 5900.
  • Page 2 2. Make sure your scanner has been installed and works properly. 3. Power off your scanner. 4. Remove the scanner cover. Open the cover until it stands vertically to the scanner, then pull upward to remove. 5. Hold the ADF-650/651 firmly on both sides in a vertical position, with its hinge studs and connector at the bottom.
  • Page 3 7. Plug the feeder's connector into the 15-pin Accessory port at the back panel of the scanner. Secure the connector by tightening the retaining screws. 8. Turn on your scanner, and wait for the light on the scanner’s front panel to stop blinking and stay on steady. Your system will detect the scanner with ADF-650/...
  • Page 4 Scanning Text Originals for OCR 1. Make sure you have ScanWizard 5 installed on your computer, and do not load any material at this point. 2. Launch ScanWizard 5 in stand-alone mode. Specify your own scan settings by clicking on the Control Panel (see settings below);...
  • Page 5 b) Pull out the top tray extender for better paper support if the length of the originals exceeds 10 inches. c) Align the material with the center of the feed tray by sliding the two guide arms in toward the stacked sheets if the width of the originals is less than 8.5 inches.

  • Page 6: Fixing Paper Jams

    • If the check box “Save multiple pages as a single file” is enabled, all pages of the originals are scanned before they are saved under a single file name. Take note that this will not work if the chosen output file format is PDF. This file format can only be saved and assigned with individual file names for each page.

  • Page 7: Maintenance

    2. With the cover fully opened, pull out the jammed document from the feeder by doing the following: • Pull the paper in a forward direction if paper is jammed in the first stage (paper feed) rollers. • If the paper is jammed in the second stage (scanning) rollers , you may pull it out in either direction (forward or backward).

  • Page 8: Specifications

    Cleaning the Rollers Prolonged use of the ADF-650/651 may result in accumulation of ink and other residue on the feeder's rollers, affecting their efficiency. Check for residue on the rollers if paper flow through the rollers becomes erratic. Open the feeder cover to periodically clean the rollers with a lint-free cloth or a swab moistened with water.

This manual is also suitable for:

Scanmaker adf-650Scanmaker adf-651