Download
Share
Print this page
Vivotek AM-116 Installation Manual
  1. Manuals
  2. Brands
  3. Vivotek Manuals
  4. Camera Accessories
  5. Fixed Dome AM-116
  6. Installation manual
Vivotek AM-116 Installation Manual

Vivotek AM-116 Installation Manual

Sd83xxe speed dome mounting accessories
Hide thumbs Also See for AM-116:

Advertisement

Quick Links

Download this manual
VIVOTEK SD83XXE Speed Dome
Mounting Accessories
AM-116/117 Pendant Pipe
AM-118 Pendant Head
AM-221 Gooseneck
AM-231 Parapet Mount
AM-519 Pendant Adaptor
Corresponding part numbers:
AM-116: 900014300G
AM-117: 900014400G
AM-118: 900014600G
AM-221: 900014800G
AM-231: 900015000G
AM-519: 900014900G
Installation Guide
IP Sur veillance
Rev. 1.1

Advertisement

loading

Related Manuals for Vivotek AM-116

Summary of Contents for Vivotek AM-116

  • Page 1 VIVOTEK SD83XXE Speed Dome Mounting Accessories AM-116/117 Pendant Pipe AM-118 Pendant Head AM-221 Gooseneck AM-231 Parapet Mount AM-519 Pendant Adaptor Installation Guide Corresponding part numbers: AM-116: 900014300G AM-117: 900014400G AM-118: 900014600G AM-221: 900014800G AM-231: 900015000G AM-519: 900014900G Rev. 1.1 IP Sur veillance...

  • Page 2: Mechanical Drawings

    Revison History: Rev. 1.0: Initial release Rev. 1.1: Adding corresponding ordering part numbers and supported speed dome models. Compatible VIVOTEK Cameras Speed Dome SD8364E, SD8363E, SD8333E, SD83x4E, SD83x6E, SD8362E Mechanical Drawings AM-118 Pendant Head 60.3 1-1/2" PS11...
  • Page 3 AM-116 20cm Pendant Pipe AM-117 40cm Pendant Pipe 1 1/2" PS11 1 1/2" PS11 n 50.8 AM-519 Pendant Adapter 1 1/2" PS11 (comes with the network camera) n 50.8 60,3 50,8 37,5 43,6 1-1/2" PS11X17mm (L)
  • Page 4 AM-221 Gooseneck 107.8 405.8 AM-231 Parapet Mount 1077.95 228.15...
  • Page 5 AM-231 Parapet Corner Mount 1077.95 202.95...
  • Page 6 AM-231 Parapet Mount - Alignment Sticker 228.15 parapet top 178.15 AM-231 Corner Mount - Alignment Sticker 143.5 PARAPET TOP Fold Line...

  • Page 7: Preparation Before Installation

    Preparation before Installation Connect Ethernet cable and IO wires (this may include the AC24V wires) to the interface section of the camera, and then combine the interface section with the dome cap. Note that you must route cables through the waterproof connector and the rubber seal plug, and install them to the dome cap.
  • Page 8 Mounting & Cabling IV-1. Pendant Pipe Mounting: AM-116/-117 & AM-118 Shown below are the dimensions of a pendant mount configuration using the 40cm pendant pipe. AM-118 AM-117 446.2 mm AM-519 321.4 mm 204.8 mm...
  • Page 9 IV-1-1. Pendant Mount without Pendant Pipe: AM-118 Below are the sample procedures using a pendant head and pendant pipe: 1. Determine a hard surface ceiling location, and use the alignment sticker to mark the positions where holes will be drilled to secure the pendant head. Hammer the anchors into the ceiling.
  • Page 10 3. Route power lines and other wires through the pendant head. You may apply a 1 inch conduit. 4. Secure the pendant head to ceiling by driving screws through its mounting holes. Depending on the length of your cables, you may need the help from your colleague for holding the camera top section.
  • Page 11 5. Secure the camera's top section to the pendant head by fastening 3 M5x8 screws. When done, secure the connection using an included 3mm hex wrench. 6. Install the camera to the top section. See your Quick Installation Guide or page 15 for details.
  • Page 12 IV-1-2. Pendant Mount with Pendant Pipe: AM-116/AM-117 & AM-118 Below are the sample procedures using a pendant head and pendant pipe: 1. Determine a hard surface ceiling location, and use the alignment sticker to mark the positions where holes will be drilled to secure the pendant head. Hammer the anchors into the ceiling.
  • Page 13 3. Route power lines and other wires through the pendant head. You may apply a 1 inch conduit. 4. Secure the pendant head to ceiling by driving screws through its mounting holes. Depending on the length of your cables, you may need the help from your colleague for holding the camera top section.
  • Page 14 5. Secure the camera's top section to the pendant head by fastening 3 M5x8 screws. 6. Install the camera to the top section. See your Quick Installation Guide or page 15 for details.
  • Page 15 IV-2. Gooseneck Mounting: AM-221 Below is a sample procedure using a gooseneck bracket: 1. Determine a hard surface wall location. Use the alignment sticker to mark the positions where holes will be drilled for the gooseneck bracket. 2. Drill 4 pilot holes (10mm in diameter and 5.5cm deep) into the wall, and then hammer in threaded anchors.
  • Page 16 6. Rotate the camera clockwise until its alignment mark is aligned with the "C" mark. 7. Use the included T25 stardriver to tighten the 3 anti-tamper screws from the top. Make sure all parts have been securely tightened. C mark The dimensions of the gooseneck installation are shown below.
  • Page 17 IV-3. Parapet Mounting: AM-231 The screws included in the parapet set are: IMPORTANT: Sleeve anchors 5/16" x3" The parapet wall should have a Hex bolts M8x25 concrete strength of 4000 PSI or higher. Hex bolts M8x70 Each sleeve anchor can withstand an Hex lock nuts M8 800kgs pull-out force.
  • Page 18 Below is a sample procedure using the parapet mount bracket: 1. Determine a hard surface location. Use the alignment sticker to mark the positions where holes will be drilled for the bracket. 2. Drill 6 pilot holes (10mm in diameter and 5.5cm deep) into the wall, and then hammer in the sleeve anchors.
  • Page 19 NOTE: If you install the corner parapet bracket, use the included alignment sticker, and mark the drill holes through the mounting slots on the brackets.
  • Page 20 4. Use a crescent wrench to secure the outer brackets to the brackets on the wall using the M8x25 hex bolts and washers. Do not completely tighten the bolts yet! When the speed dome is installed to the mount pipe, it needs to be swiveled out to the desired position.
  • Page 21 7. Install the top section of the camera to the pipe arm by driving 3 M5 x8 screws. 8. Insert the pipe arm into the round openings on the brackets until it is rested on the bottom bracket.
  • Page 22 9. Install the camera to the top section. For installation details, refer to the Quick Installation Guide or page 15 in this document. 10. Swivel the pipe arm outwards to the opposite position. Use the M8 x70 bolts to secure the pipe arm to the brackets.
  • Page 23 A corner parapet installation should look like this when its installation is completed.
  • Page 24 This page is intentionally left blank.

This manual is also suitable for:

Am-117Am-118Am-221Am-231Am-519