Page 1
VIVOTEK Fixed Dome Series Mounting kit Using AM-52E Mounting Adapter, AM-118 Pendant Head (indoor), AM-114 Pendant Head (outdoor) AM-116 and AM-117 Pendant Pipes, AM-522 NPT adaptor AM-218 Wall Mount, AM-312 Pole Mount, AM-412 Corner Mount Installation Guide Corresponding part number:...
Compatible Accessories Compatible Accessories (1): AM-312 Pole Compatible Accessories (2): AM-412 Mount Bracket Corner Mount Bracket Compatible Accessories (4-3): AM-218 Compatible Accessories (5-1): AM-118 Wall-mount Bracket Pendant Head Compatible Accessories (5-2): AM-114 Compatible Accessories: AM-522 Pendant Head Pendant NPT Adaptor...
Page 5
Compatible Accessories (5-2): AM-116 and AM-117 Pendant Pipe Shown below are the mounting dimensions using a 40cm pendant pipe (AM-117). AM-118 140 mm AM-117 438.2 mm 552.2mm FD9380 24.5mm 89.5 mm 117.1 mm...
Page 6
AM-118 3. Secure pandant head using the included screws. 4. Install the pendant pipe. 5. Tighten the retention screw using the hex wrench. 6. Install the AM-52E. 7. Tighten the retention screw using the included hex wrench. AM-116/ AM-117 AM-52E...
Page 7
8. Pull the cables through the pendant pipe, and install the waterproof cable gland. Install the camera using the corresponding mounting holes. Some cameras come with a side-routing cutout. Use the included side lid to seal the cutout.
Page 8
AM-118 AM-522 3/4" Female adapter 3/4" pendent pipe AM-52E 115 mm 1. Determine a hard surface ceiling location, and use the included alignment sticker for marking three mounting holes as where holes will be drilled to secure the pendant head.
Page 9
3. Secure the pandant head using the included screws. 4. Install the AM-522 adaptor and the NPT female-female coupler (user-supplied) 5. Tighten the hex socket screw using the hex wrench. 6. Install the 3/4" NPT pipe of a preferred length. 7. Install the AM-52E. AM-118 AM-522 NPT female- female coupler 3/4”...
Page 10
8. Pull the cables through the NPT pipe and the camera base. Align the camera's mounting holes with the associated holes on the bracket. It is recommended to install the waterproof cable gland.
Page 11
Using Other Accessories 4-1. Wall-mount Installation - AM-218 Below is a general, sample procedure using a gooseneck bracket: 1. Route the Ethernet and/or other cables through the wall and the bracket. 2. Locate the position where you want to install the wall-mount bracket and camera. Drill holes on the wall for securing the bracket and for routing the cables.
Page 12
4-2. Corner Mount Installation Dimension drawing: M8X20mm SUS 302 4- 6 4- 7 3- 4,5 56,29 315,25...
Page 13
M5X20 X4 M4X15 X4 M6X20 X4 M8 X2 4mm X1 5mm X1 Below is a general, sample procedure using a Corner mount bracket: 1. Combine the two metal pieces together using the M8 hex nuts and washers.
Page 14
2. Align the assembled brackets with the desired position. Align screw holes on the brackets against the wall. Drill holes on the wall for securing the bracket and for routing the cables. Hammer the anchors into the wall. Note that these screws and wall anchors are user-supplied.
Page 15
3. Install the AM-218 bracket to the top of AM-312. Install the AM-52E to the bracket and tighten the retention hex screw. AM-218 AM-52E Dome camera...
4-3. Pole Mount Installation The pole mount bracket is designed to accommodate a pole in a diameter ranging from 90 ~ 152mm (3.5 ~ 6 inches) 84,9 55° 55° 4-OB 25.5X5.5mm 4- 6 3- 4,5 4- 7 56,29 173,79...
Page 17
M6X20 X4 M5X20 X4 M4X15 X4 Stainless steeel strap X2 Below is a general, sample procedure using a Pole mount bracket: Use the mounting holes indicated below for the conduit box.
Page 18
1. Secure the AM-719 conduit box to bracket using the M4 screws, washers, and hex heads. A hex crescent wrench is required. You can do this before you install the pole- mount bracket. 2. Pass the stainless steel straps through the bracket and around the pole.
Page 19
The corresponding mounting holes and cameras are shown below: Combination Compatible Models Screw Direct installation: A: FD9360-H, FD9380-H M4x8L AM-52E B: IT9388-HT C: IT9360-H, IT9380-H 6. Install the AM-52E to the bracket and install your camera to the AM-52E adapter bracket.