Vivotek fixed dome series mounting adapter (13 pages)
Summary of Contents for Vivotek Fixed Dome Series
Page 1
VIVOTEK Fixed Dome Series Mounting kit Using AM-525 Mounting Adapter, AM-51C Mounting Adapter, AM-513 Mounting Adapter, AM-118 Pendant Head (indoor), AM-116 and AM-117 Pendant Pipes, AM-522 NPT adaptor AM-221 Gooseneck, AM-212 Wall Mount, AM-311 Pole Mount, AM-411 Corner Mount Installation Guide...
Compatible Accessories Compatible Accessories (1): AM-311 Pole Mount Bracket Compatible Accessories (2): AM-411 Corner Mount Bracket Compatible Accessories (4-1): AM-221 Gooseneck Bracket Compatible Accessories (4-2): AM-212 Wall-mount Bracket Compatible Accessories (5-1): AM-118 Pendant Head Compatible Accessories: AM-522 Pendant NPT Adaptor...
Page 5
Compatible Accessories (5-2): AM-116 and AM-117 Pendant Pipe Shown below are the dimensions using a 40cm pendant pipe (AM-117). AM-118 140 mm AM-117 438.2 mm 565.9 mm 24.5 mm 103.2 mm 155 mm...
Page 6
Direct Installation 3-1. Using the Pendant Pipe 1. Determine a hard surface ceiling location, and use the included alignment sticker for marking three mounting holes as where holes will be drilled to secure the pendant head. 2. Hammer in the plastic anchors. AM-118 3.
Page 7
8. Pull the cables through the pendant pipe, and the camera base. Install the camera. Use a crimping tool to connect the Ethernet wires to an RJ45 connector.
Page 8
3-2. Using the 3/4" NPT Pipe AM-118 AM-522 3/4" Female adapter 3/4" pendent pipe AM-525 155 mm 1. Determine a hard surface ceiling location, and use the included alignment sticker for marking three mounting holes as where holes will be drilled to secure the pendant head. 2.
Page 9
3. Secure the pandant head using the included screws. 4. Install the AM-522 adaptor and the NPT female-female coupler (user-supplied) 5. Tighten the retention screw using the hex wrench. 6. Install the 3/4" NPT pipe of a preferred length. 7. Install the AM-525. AM-118 AM-522 NPT female-...
Page 10
8. Pull the cables through the NPT pipe and the camera base. Install the camera. Use a crimping tool to connect the Ethernet wires to an RJ45 connector.
Page 11
1. Please refer to the AM-513 Installation Guide for details about the mounting holes, and use a hammer and flat-blade screwdriver to open the knock out holes you prefer to use. Fixed Dome series FD8367-V / FD8338-HV / FD8367-TV 2. Combine the AM-525 and AM-513 by driving 4 included screws.
Page 12
1. Please refer to the AM-51C Installation Guide for details about the mounting holes, and use a hammer and flat-blade screwdriver to open the knock out holes you prefer to use. Fixed Dome series FD9381 / FD9371 / FD836B /...
Page 13
Using Other Accessories 6-1. Gooseneck Installation - AM-221 Below is a general, sample procedure using a gooseneck bracket: 1. Route power lines and other cables through the wall and the bracket. 2. Locate the position where you want to install the gooseneck bracket and camera. Drill holes on the wall for securing the bracket and for routing the cables.
Page 14
The same installation method applies to the AM-212 wall-mount bracket.
Page 15
6-2. Corner Mount Installation Below is a general, sample procedure using a Corner mount bracket: 1. Combine the two brackets together using the included nuts and washers. 2. Align the assembled brackets with the desired position. Align screw holes on the brackets against the wall.
6-3. Pole Mount Installation Below is a general, sample procedure using a Pole mount bracket: 1. Route power lines and other cables through the included cable gland, pass them through conduits (separately purchased), and install the cable gland to the pole mount bracket.