ETC echoflex ELED3 Configuration Manual
Tri-zone dimming controller
Hide thumbs
Also See for echoflex ELED3:
- Installation manual (8 pages) ,
- Configuration manual (24 pages)
Subscribe to Our Youtube Channel
Related Manuals for ETC echoflex ELED3
Summary of Contents for ETC echoflex ELED3
- Page 1 Tri-Zone Dimming Controller Models: ELED3 and ELED3H Configuration Guide Part Number: 8189M2410 Rev.A Released: 2022-10...
- Page 2 To view a list of Echoflex trademarks and patents, go to echoflexsolutions.com/ip. All other trademarks, both marked and not marked, are the property of their respective owners. Echoflex intends this document, whether printed or electronic, to be provided in its entirety.
-
Page 3: Table Of Contents
Table of Contents Introduction Features Document Conventions Help from Technical Services Configuration Options Simple Tap Instructions Radio Communications Repeater Function Status Message Radio Range Confirmation Dimming Outputs Near-Cross Technology Switch Operation Timed Switches Occupancy-Based Lighting Applications Occupancy Sensor Auto-OFF Timer Save State Grace Timer Dual Technology Occupancy Sensors Occupancy Sensors and Partial-ON... - Page 4 Create a Shared Occupancy Space Hospitality Applications Daylight Harvesting Applications Daylighting Control Override Closed Loop Control Open Loop Control Controller Presets User Interface Power LED and Learn LED Learn Button Remote Linking Solution Clear Button LED Display Blink Indications Device Count Codes Linking Activities Compliance FCC Compliance...
-
Page 5: Introduction
Introduction The Tri-Zone Dimming Controller is a fully configurable and complete stand-alone dimming and lighting controller designed to perform common lighting control applications based on input from wireless linked sensors and switches. It includes 0–10 volt dimming channels for three individual dimming zones and a robust 20 A relay (16 A relay in High voltage ELED3H model) for ON/OFF control of large controlled... -
Page 6: Document Conventions
Document Conventions Echoflex's user documentation is designed for print or electronic use. Cross-references highlighted in this document are links to the referenced section of the guide. Configuration parameters are emphasized in italics. Switch actions (ON/OFF) and dimmer events (lights ON/OFF) are emphasized in ALL CAPS. Buttons are emphasized in [Bold Bracket]. This document uses the following conventions to draw your attention to important information. -
Page 7: Configuration Options
Configuration Options The controller provides dimming and switching control using input received from compatible Echoflex devices. It operates based on: Ambient light levels monitored by a wireless photo sensor • Occupancy state monitored by a wireless occupancy sensor • Switch action from a wireless wall or keycard switch •... -
Page 8: Status Message
Status Message The controller can broadcast a message per EEP: A5-11-01 Status Feedback Message. A message broadcasts every 100 seconds. The status message can be enabled/disabled using Simple Tap instructions. 1. Press and hold the [Learn] button on the controller. 2. -
Page 9: Switch Operation
Switch Operation The controller operates with single, dual-paddle wall, wave, and hand-held Echoflex switches as well as button station transmitters including the Multi-Button Interface (MBI) Switch Station and the Multi-Scene Station (MSS). A switch can be linked to a single channel or all the channels. -
Page 10: Save State
3. Set a number of minutes for the timer period. Tap the [Teach] button the number of times indicated in the table below to set the timer period. The light responds a number of times to confirm the change and then returns to normal operation. Taps Occupancy Sensor Timer Light Response... -
Page 11: Occupancy Sensors With Switches
To set the partial-OFF value and enable/disable automatic partial-OFF: 1. Use a linked switch with the light ON and dim to the target partial-OFF value. 2. Press the [Teach] button on the sensor, and then do one of the following: Click the switch OFF three times followed by one ON to enable partial-OFF. -
Page 12: Hospitality Applications
Connect Controllers You can select any controller to send a shared occupancy ID and connect other controllers. If the selected controller does not have a shared occupancy ID (default), it will generate one to send. If the controller has a shared occupancy ID, it will send the shared occupancy ID it has recorded. -
Page 13: Daylight Harvesting Applications
Daylight Harvesting Applications Based on the ambient light level in the space, the controller modulates light intensity from lighting fixtures on the primary and secondary daylighting channels, Channel 1 and 2 respectively. The daylight harvesting application does not affect the relay operation. When daylighting is active and is driving the two outputs, a switch, gateway command or occupancy sensor cannot force the light level higher. -
Page 14: Open Loop Control
3. Tap the [Teach] button on the mounted sensor three times to set the daylight harvesting parameters to closed loop function. The light ramps up to full ON and then dims to OFF to acknowledge the change. 4. Move away from the sensor so your shadow does not affect the light level the sensor records. -
Page 15: Controller Presets
To set the open loop maximum output set point and minimum output set point using Simple Tap, a photo sensor with monitoring range greater than 2500 lux must be linked to the controller. Note: The set points are calculated as a percentage of the photo sensor's full scale range. -
Page 16: User Interface
User Interface Note: Garibaldi Pro software is the ideal tool to set up your project and configure settings, or even to make edits if your project has been pre-commissioned. Garibaldi Pro is available for download at echoflexsolutions.com. Two buttons on the controller can be used to activate features and set specific configurations directly on the device. -
Page 17: Remote Linking Solution
Remote Linking Solution Use the following method to link the first switch if you cannot access the [Learn] button on a controller that has not been pre-commissioned and you do not have Garibaldi Pro software. This method only works if there are no switches linked to the controller. You cannot link a scene station using this method. -
Page 18: Blink Indications
Blink Indications The tables below describe the LED codes that identify linked devices and the LED indications that describe linking activities. A different color LED identifies each channel. Red is for Channel 1, Green is for Channel 2, and blue is for Channel 3. Device Count Codes The following codes provide a visible report of the devices that are linked to the controller. -
Page 19: Compliance
Compliance For complete regulatory compliance information, see the Echoflex Tri-Zone Dimming Controller datasheet at echoflexsolutions.com. FCC Compliance Echoflex Tri-Zone Dimming Controller (For any FCC matters): Echoflex Solutions, Inc. 3031 Pleasant View Road Middleton, WI 53562 +1 (608) 831-4116 echoflexsolutions.com This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received;... - Page 20 Tri-Zone Dimming Controller Configuration Guide...
- Page 21 Compliance...
- Page 22 Tri-Zone Dimming Controller Configuration Guide...
- Page 23 Compliance...
- Page 24 Corporate Headquarters n Middleton, WI, USA | +1 608 831 4116 echoflexsolutions.com | Email info@echoflexsolutions.com | Support service@echoflexsolutions.com ©2022 Echoflex Solutions, Inc. Trademark and patent info: echoflexsolutions.com/ip Product information and specifications subject to change. Echoflex intends this document to be provided in its entirety. 8189M2410 Rev A Released 2022-10...
Need help?
Do you have a question about the echoflex ELED3 and is the answer not in the manual?
Questions and answers