Advertisement
Quick Links
Advertisement
Related Manuals for PDMOVIE REMOTE AIR PRO 3
Summary of Contents for PDMOVIE REMOTE AIR PRO 3
-
Page 2: Notice For Use
PD-MX Notice For Use 1. REMOTE AIR PRO 3 is for professional filmmaking three-channel wireless follow focus system. It can easily and quickly control the FOCUS, IRIS and ZOOM of CINE/SLR lenses remotely. 2. Before using the product, please read the instruction manual carefully or watch the instructional video to understand the usage skills of the product. -
Page 3: Configuration List
Configuration List ① ② ③ ④ ⑤ ⑥ Controller MOTOR PRO MOTOR AIR LI-42B Battery LI-42B Battery Charger Serial motor cable 0.4m (6 pins) ⑦ ⑧ ⑨ ⑩ D-Tap Power Cable 0.7m USB charging cable 0.9m Micro USB 15mm/19mm Mark disk Short Antenna (6-pin) (6-pin) - Page 4 Product Sketch Map Controller OLED Screen Focus Control handwheel Lights for Focus Control Wheel FOCUS IRIS ZOOM Lights for Zoom Lights for Iris Pull-push Lever Pull-push Lever Imperial 1/4 threaded hole Lights for Controller Status Battery placement Battery compartment Press down first, then push out PD4-HT Front Sketch Map PD4-HT Back Sketch Map Zoom Function Button...
- Page 5 Motor Product Sketch Map 0.8 Gear Antenna Socket 6-Pin Socket 7V-20V Lights for Motor Status OLED Screen U-clamp Side view of the motor Front view of the motor Function Button The bottom view of the motor * The motor diagram is mainly based on the PD-RP receiving motor. The difference between PD-MX and PD-RP is that PD-MX has no OLED screen and antenna socket, and other parts are exactly the same.
- Page 6 Instruction Manual Install 1. Install the Motor Install the motor on the 19mm or 15mm conduit (requires an adapter ring), pay attention to clamp the motor gear and lens gear, then lock the U clip, and finally install the antenna and power cable or serial cable on the receiver motor (PD-RP).
- Page 7 Set Up Instruction Manuals 3. Start the controller and motor Press and hold the controller's ON/OFF button for three seconds and release when the display lights up. The motor does not need to be switched on and off, it will automatically start when it is powered on, and it will automatically turn off when it is powered off.
- Page 8 Controller button Motor button Channel Indicator color Control FOCUS GREEN ZOOM Short press 2 times BLUE IRIS Yellow Alternate channel Short press 2 times Cyan Alternate channel Short press 3 times Purple Alternate channel Instruction Manuals Set Up 6. Calibrate the lens Method 1: Press and hold any of the FOCUS, ZOOM and IRIS buttons on the controller for three seconds, the motor will will automatically calibrate the lens travel.
- Page 9 *When the controller and the motor are in the same signal channel and control channel, and the lens is automatically calibrated, it can be used. 7. Adjust the speed Before using the focus of the controller to control the handwheel and the push-pull Lever on both sides, please check whether the motors in the corresponding control channels can be used normally.
-
Page 10: Additional Accessories
Step 3 After starting the controller，can first adjust the color of the controller's FOCUS/IRIS/ZOOM indicator to red/blue/green. Log in to PDMOVIE official website to get REMOTE AIR APP usage tutorial. The HELP item of the SET interface in the APP also has a complete introduction to APP functions. -
Page 11: Supplementary Instructions
1. The motor comes standard with 0.8M gear,Special circumstances require gears (0.4m, 0.5m, 0.6m), you can contact the after-sales service or buy them at the PDMOVIE official website. 2. Any problems with the motor during calibration,Just click the motor button once to terminate the calibration.