Omron C200HX-CPU E Series Installation Manual page 251

A manual revision code appears as a suffix to the catalog number on the front cover of the manual.
The following table outlines the changes made to the manual during each revision. Page numbers refer to the
previous version.
Revision code
1 June 1996
2 March 1997
3 August 1997
4 October 1997
5 June 2000
6 January 2001
07 November 2001
Revision History
Cat. No. W302-E1-09
Date
Original production
Relay Output Units changed to Contact Output Units
throughout the manual.
Page 11: 64-point Units column added to the second
table in CPU Units.
Pages 20, 22, 82, 98, 111, 177: C200H-OC222V,
C200H-OC224V, and C200H-OC226 Contact Output
Units added.
Page 21: Note on C200H-OC226 dimensions added.
Page 23: The settings corrected for I/O Number Set-
ting Switch at the bottom of page.
Page 42: Ambient Conditions precautions replaced.
Page 43: Note on tightening torque added.
Page 50: Note 3 corrected.
Pages 54, 56: Crimp terminals information corrected.
Added the ZE-version C200HX/HG/HE CPU Unit to
Section 2, Appendix A, and Appendix B.
Pages 17, 18, 54, 58: AC input terminal information
Page 11, 19. 57, 85, 185: Added C200HW-PA204R.
Page 16: "KB" corrected to "K words" in the table.
Page 18: Addition to first paragraph in 2-2-4 Power
Supply Units. Information on AC input terminals in the
diagram corrected.
Page 19: Added sentence on power consumption
restrictions and tables on CPU Units and Backplanes
for C200HW-PA204R.
Page 41, 86, 188: Added Controller Link Unit and PC
Card Unit.
Page 56: Corrections and additions made to the note
in the diagram.
Page xii to xiv: Major changes made to safety
information.
Pages 11, 12, 13, 19, 20, 48, 49, 59, 61, 89, 90, 91,
103, 189, 196, 201: Information related to Power Sup-
ply Units and/or Backplanes added/changed.
Page 15: Information on DIP switch pin 5 changed.
Pages 22, 92: Information on Triac Output Units add-
ed/changed.
Pages 24, 26, 93, 191: Information related to Group-2
High-density I/O Units added.
Pages 30, 94, 192: Information on Position Control
Units and/or Motion Control Units added.
Page 40: Information on the number of mountable
Master I/O Units added.
Page 47: Minor change to graphic.
Page 62: Power consumption value in first line
changed from 50 to 40.
Page 12: Note added after table.
Page xiv: Memory Units changed to Memory Cas-
settes and Power Supply Units added to the precau-
tion item for turning OFF the power supply.
Page 29: I/O number setting changed for two 40-pin
Revision code
Revised content
Pages 55, 56: Crimp terminals information corrected.
EC Directives information added.
Page 57: Tightening torque information added.
Page 59: Contact output circuit corrected.
Pages 76 to 78: Output Unit Relay and Output Units
added to the procedure.
Page 85: Relay added to Optional Products.
Page 93: Output capacity corrected in the table.
Page 96: Connector models corrected.
Page 112: New Contact Output Units reflected.
Pages 116, 117, 122: Circuit configurations corrected
for C200H-OD212, C200H-OD213, and
C200H-OD21A.
Page 182: C200H-OC226 dimensions added.
corrected and added to.
Page 70: Note on cycling the power supply added to
the procedure.
Page 56, 101/102: Added information on 24-VDC out-
put.
Page 92: Added CompoBus/S and CompoBus/D Mas-
ter Units.
Page 101: Separated output capacities and added
specifications for RUN output. Enclosure rating cor-
rected.
Page 123: Graphs corrected.
Page 196: Analog Timer Unit and Group-2 High-den-
sity I/O Units dimensions corrected.
Page 67: Precautionary information added.
Page 71: One sentence added to information on
power interruptions.
Page 78: Information added to table.
Page 81: Information on Output Units added.
Page 95: Information on Voice Unit added.
Pages 105, 137: Changes made in several places.
Page 106: Information on RUN output added.
Page 107: Changes made to bit addresses.
Page 147: Information on DC Input Units added.
Pages 148, 150, 159, 161, 169, 171: Circuit configu-
ration graphics and information on manufacturing
numbers added.
Pages 149, 151, 162, 170, 171: Notes added.
Page 151: Information on Transistor Output Units
added.
Page 180: Information on B7A Interface Units added.
connectors.
Page 77: Power interruption duration changed.
Page 146: Note changed to clarify indicator condi-
tions.
237