Related Manuals for Ubiquiti PBE-M5-300-US
Summary of Contents for Ubiquiti PBE-M5-300-US
- Page 1 PBE-M5-300 Quick Start Guide Package Contents Reflector Antenna Feed Rear Housing Mounting Bracket Pole Clamp U-Bolt Flange Nuts (Qty. 2) Washers (Qty. 2) PoE (24V, 0.5A) with Mounting Bracket Power Cord...
-
Page 2: Installation Requirements
AC ground of the PoE. We recommend that you protect your networks from harmful outdoor environments and destructive ESD events with industrial-grade, shielded Ethernet cable from Ubiquiti. For more details, visit ui.com/toughcable Hardware Overview... -
Page 3: Application Examples
LAN and DHCP server. PBE-M5-300 Quick Start Guide Reset Button To reset to factory defaults, press and hold the Reset button for more than 10 seconds while the device is powered on. Alternatively, the device may be reset remotely via a Reset button located on the bottom of the PoE adapter. Release Button After you assemble the device, check the Release button;... -
Page 4: Installation
The PowerBeam mounted outdoors without the Reflector installed provides outdoor- PBE-M5-300 Quick Start Guide to-indoor coverage using the 3 dBi Antenna Feed only. Installation... - Page 5 PBE-M5-300 Quick Start Guide...
- Page 6 PBE-M5-300 Quick Start Guide...
-
Page 7: Connecting Power
PBE-M5-300 Quick Start Guide Connecting Power WARNING: The switch port must comply with the power specifications listed in this Quick Start Guide. -
Page 8: Installer Compliance Responsibility
The airOS Configuration Interface will appear, allowing you to customize your settings as needed. For details, refer to the User Guide available at ui.com/download/airmax You can also manage your device using the Ubiquiti Internet Service Provider Application. Setup using the UISP™ app requires the U-Installer, sold separately. Installer Compliance Responsibility Devices must be professionally installed and it is the professional installer’s... -
Page 9: Specifications
Select your antenna from the list. If Calculate EIRP Limit is enabled, transmit output PBE-M5-300 Quick Start Guide power is automatically adjusted to comply with the regulations of the applicable country. Note the requirements and antenna types listed below. Cable Loss (When applicable) Enter the cable loss in dB. -
Page 10: Safety Notices
PBE-M5-300 PBE-M5-300 Quick Start Guide Temperature Shock Test IEC 68-2-14 UV Test IEC 68-2-5 at 40° C (104° F) Equivalent: ETS 300 019-1-4 Wind-Driven Rain Test ETS 300 019-1-4 Equivalent: MIL-STD-810 G Method 506.5 Operating Temperature -40 to 70° C (-40 to 158° F) Operating Humidity 5 to 95% Noncondensing Certifications... -
Page 11: Limited Warranty
c. Contact a qualified electrician or the manufacturer if there are questions about the PBE-M5-300 Quick Start Guide installation prior to connecting the equipment. d. Protective earthing is provided by Listed AC adapter. Building installation shall provide appropriate short-circuit backup protection. e. -
Page 12: Australia And New Zealand
Le présent appareil est conforme aux CNR d’ISDE Canada applicables aux appareils radio PBE-M5-300 Quick Start Guide exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1. l’appareil ne doit pas produire de brouillage; 2. l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. -
Page 13: Weee Compliance Statement
MHz frequency range within all member states. Note: Operation in the 5.8 GHz frequency band is prohibited in BFWA member states. Other countries listed may use the 5.8 GHz frequency band. WEEE Compliance Statement Declaration of Conformity Online Resources © 2022 Ubiquiti Inc. All rights reserved.
Need help?
Do you have a question about the PBE-M5-300-US and is the answer not in the manual?
Questions and answers