Ubiquiti PBE-5AC-620 Quick Start Manual
Hide thumbs
Also See for PBE-5AC-620:
- Quick start manual (29 pages) ,
- Quick start manual (9 pages) ,
- Quick start manual (22 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ubiquiti PBE-5AC-620
Summary of Contents for Ubiquiti PBE-5AC-620
- Page 1 PBE-5AC-620 Quick Start Guide Package content Back case power horn Parabolic reflector with mounting bracket support arm lower post bracket Upper Post Bracket Assembly Clamp Screws (qty: 4) Hex Head Cap Screws (Qty: lock washers Flat washers (cant.: 5) stabilizer mounts...
-
Page 2: Installation Requirements
Category 5 (or higher) shielded cabling must be used for all Ethernet connections and must be connected to the AC ground of the PoE. We recommend that you protect your networks from harmful outdoor environments and electrostatic discharge phenomena with Ubiquiti's Industrial Grade Shielded Ethernet Cable. For more information, visit ui.com/toughcable... -
Page 3: Hardware Description
hardware description bottom view Ethernet The Gigabit Ethernet port is used to connect power and must be connected to the LAN and DHCP server. reset button To restore factory defaults, press and hold the reset button for more than 10 seconds while the device is turned on. -
Page 4: Application Examples
Sign On airOS®, you can modify the wireless LED signal strength threshold value in the Wireless tab, under Signal LED Thresholds. Each LED will turn on when the wireless signal strength is equal to or greater than the threshold value set for the LED indicator. The default threshold values for these LED indicators are listed below: Ethernet The LED indicator will turn solid blue when the device is connected to an Ethernet... -
Page 5: Installation
Outdoor mounted PowerBeam with reflector installed provides directional outdoor coverage (gain dependent on reflector). The exterior mounted PowerBeam without the reflector installed provides exterior to interior coverage only through the 3 dBi feed horn. Installation... -
Page 18: Power Connection
Power connection WARNING: The port switch must meet the power specifications listed in this quick start guide. - Page 19 Optional Access airOS Connect to the airOS® configuration interface. 1. Check that your host is connected via Ethernet to the device.
-
Page 20: Installer Compliance Responsibility
For more information, see the user guide available at ui.com/download/ airmax-ac You can also manage your device using the Ubiquiti Internet Service Provider Application network management system. Configuration using the UISP™ application requires the U-Installer, which is sold separately. -
Page 21: Safety Instructions
Antenna Frequency Gain 29 dBi dish 5 GHz specs PBE-5AC-620 Dimensions 650 x 650 x 386 mm (25,6 x 25,6 x 15,2") Weight 6,4 kg (14,11 lb) 29 dBi Gain network interface (1) puerto Ethernet 10/100/1000... -
Page 22: Electrical Safety Information
1. Read, follow and save these instructions. 2. Pay attention to all warnings. 3. Only use the devices or accessories indicated by the manufacturer. WARNING: Do not use this product in a location where it may be submerged in water. WARNING: Avoid using this product during a lightning storm. -
Page 23: Important Note
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions. 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. -
Page 24: Online Resources
Note: This equipment is not entitled to protection against harmful interference and may not cause interference in authorized systems. CE marked The CE marking of this product indicates that the product complies with all applicable directives. list of countries AT BE BG CY CZ DE DK EE EL ES FI FR HR LV LT... - Page 25 © 2022 Ubiquiti Inc. All rights reserved.